LiGHTPRO 180S Castor 9 Dimmable Spotlight User Manual

: June 9, 2024
: LiGHTPRO

Table of Contents

LiGHTPRO 180S Castor 9 Dimmable Spotlight User Manual
PRODUCT DESCRIPTION
SPECIFICATIONS
PACKAGING CONTENT
INSTALLATION
CHANGING REFLECTOR
INSTALLATION OF THE LIGHTS
SAFETY
- References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LiGHTPRO 180S Castor 9 Dimmable Spotlight User Manual

180S

Produced by

FIG 4.JPG

FIG 6.JPG

Thank you for purchasing the Lightpro Castor 9.
This document contains the required information for correct, efficient and safe use of the product. Consult the user manual of your transformer for more information about the installation and connection of your lighting plan or visit our website www.lightpro.nl

Read the information in this manual carefully before using the product. Keep this manual near the product for consultation in the future.

PRODUCT DESCRIPTION

The Lightpro Castor 9 is an LED spot for outdoor use.
The fixture can be mounted on a solid surface or placed in the ground with the supplied spikes. This product may only be used as outdoor lighting in combination with the Lightpro 12-volt system. Any alterations made to the product may have consequences for the safety, guarantee and correct functioning of the product and/or other parts of the system.

SPECIFICATIONS

PACKAGING CONTENT

[Figure A] 1. Fixture Castor 9
2. Ground spike
3. Screw
4. Plug
5. Alternatieve reflector
6. Hex key (large)
7. Hex key (small)
8. Lightpro connector

Check if all parts are present in the packaging. For questions about parts, service, and any complaints or other remarks, you can always contact us.

E-mail: info@lightpro.nl.

INSTALLATION

Option 1: placement on a fixed underground or mounting to a wall [Figure B]

Remove the screw from the base using the included large hex key (Figure A [6]).
Remove the fixture from the base.

[Figure C]
• Install the base onto the underground with the included screw.
If necessary, drill a hole in the underground and use the included plug.

[Figure D]

Place the fixture in the base.
Place the screw in the base.
Put the fixture in the desired position.
Fasten the screw using the included large hex key (Figure A [6]).

Option 2: placement in the ground
[Figure E]

Place the spike underneath the base.
Properly fasten the spike.
Put the fixture in the desired position.
Fasten the screw using the included large hex key (Figure A [6]).
Place the fixture in the ground.

CHANGING REFLECTOR

The pre-installed reflector has a beam angle of 60°. If desired, it can be replaced by the included alternative reflector, which has a beam angle of 23°.

[Figure F]

Remove the screw from the fixture using the included small hex key (Figure A [7]).
Remove the head from the fixture.
Unscrew the reflector.
Remove the reflector.

[Figure G]

Place the alternative reflector.
Fasten the reflector.
Place the head in the fitting. Pay attention to the position of screw hole.
Place the screw in the fitting.
Fasten the screw using the included small hex key (Figure A [7]).

DIMMER FUNCTION
The fixture is equipped with a built-in dimmer. The light output can be set to 6 different levels.
[Figure F] • Push the button to set the desired light output.

INSTALLATION OF THE LIGHTS

Install the products in the desired position and lay the cables so they can be comfortably connected to the transformer or main cable.
If products are provided with a drain hole for water, this hole must be pointing downwards.
Use non-corrosive fixing materials (supplied as standard) if you want to bolt the products down.
Connect the lights to the main cable by using the connector as shown in figure on page 5.
Consult the manual of your transformer for more information.

SAFETY

Always fit this product so that it can still be accessed for servicing or maintenance. This product must not be permanently embedded or bricked in.
Turn off the system by pulling the plug of the transformer from the socket for maintenance.
Regularly clean the product with a soft, clean cloth. Avoid abrasives that can damage the surface.
Clean products with stainless steel parts with a stainless steel cleaning agent once per six months.
Do not use a high pressure washer or aggressive chemical cleaning agents when cleaning the product.
This can cause irreparable damage.
Protection class III: this product may only be connected to safety extra-low voltage up to a maximum of 12 Volt.
This product is suitable for outside temperatures of: -20 to 50 °C.
Do not use this product in areas where combustible gases, fumes or liquids may be stored.