TELLUR Ambia True Wireless Stereo Earphones User Manual
- June 7, 2024
- Tellur
Table of Contents
User Manual
TELLUR Ambia True Wireless Stereo Earphones
Technical specifications:
-
Bluetooth version: 5.0+EDR, BLE
-
Wireless range: 10m
-
Audio type: True Wireless Stereo
-
Supported profiles: HSP, HFP, A2DP, AVRCP
-
ENC technology: Yes, 4-microphone call technology
-
Audio codecs supported: SBC, AAC
-
Speaker Size: 6.0mm
-
Frequency response: 20Hz – 20KHz
-
Impedance: 16
-
Sensitivity: 103dB (3dB) @ 1 KHz,126mV
-
Rated power: 3mW
-
Microphone Type: 4 x MEMS
-
Sensitivity: 42dB ±3dB
-
SNR: 60dB
-
THD: less than 1% 94dB SPL @1kHz
-
Impedance: 200
-
Sweat and water resistant: IPX4
-
Features: ENC technology, Voice commands, Wearing detection, Tap control, Intelligent Switching, Auto-connect
-
Music play time: Up to 3.5 hours and up to 25 hours including charging case
-
Standby time: Up to 120 hours
-
Charge time: Approx. 2 hours
-
Battery capacity: 500mAh/3.7V (charging box), 30mAh /3.7V (earphones)
-
Charging plug: Type-C
-
Dimensions: 43 x 24.5 x 18 mm
-
Charging case dimensions: 72.6 x 32.6 x 28 mm
-
Weight earphone: 5g
-
Weight charging case: 38g
-
Color: Black
-
Package includes: 1 x Ambia True Wireless Earphones
1 x Charging case
1 x USB to Type-C cable
3 x Set of eartips
1 x User manual -
Operating temperature: -15°C to 45°C
-
Product Code: TLL511361
-
EAN: 5949120002691
Features
Environmental Noise Canceling technology (ENC)
Each earphone is equipped with 2 high-performance MEMS microphones with ENC
technology for a better environmental noise cancelation when making hands-free
calls (especially in rowdy environments: on the street, in coffee shops,
restaurants, open plan offices etc.).
Wearing detection
Built-in infrared sensors let the earphones know when you are wearing them.
You can remove either earphone to pause music automatically or you can put the
earphone back in your ear to resume playback.
Voice commands
Voice commands allow you to answer/reject and incoming call and control your
music without touching your smartphone or earphones.
Tap control
Built-in triaxial acceleration sensor allows tap control for music and hands-
free calls.
Intelligent switch
The integrated Bluetooth chipset enables an automatic switch between the main
earphone and the auxiliary one. This option allows you to use one earphone at
a time and double your hands-free talk autonomy.
Automatic connection
After pairing the earphones with your device via Bluetooth, the earphones will
reconnect automatically whenever you open the charging case.
Stunning sound
Equipped with superior dynamic drivers and a balanced audio equalization,
Ambia earphones offer a stunning sound with a crisp treble, natural high notes
and a deep, rich bass.
Fit & comfortable wear
Ergonomic in-ear design, light, soft and skin-friendly silicone with 3 pairs
of replaceable ear tips (S, M, L) ensure a fit and comfortable wear.
Turning on
With the earphones inside the charging case, open the case and the earphones
will power on automatically.
Note! Please make sure the earphones are charged for more than 10 minutes (in the charging case) before using them for the first time.
Connecting and disconnecting
1. Connect
1.1. With the earphones inside the charging case, open the charging case and
press the button from the back of the case for 5 seconds, until the blue light
starts flashing.
1.2. Turn on your mobile phone’s Bluetooth, search for “Tellur Ambia” and connect it.
2. Automatic reconnection
If the earphones have already been paired with a mobile phone, open the
charging case and the earphones will reconnect with the phone automatically
(if the two devices are within Bluetooth range).
3. Disconnect
The earphones will automatically disconnect from your mobile phone when the
charging case will be closed (with the earphones inside).
4. Automatically disconnect outside Bluetooth range
When the earphones and your mobile phone are out of the Bluetooth range (10
meters), the earphones will automatically disconnect from your phone. If you
return to the signal connection range within 3 minutes, the earphones will
reconnect automatically.
5. Connect with another phone
If you want to connect the earphones with another phone, please follow the
steps described in the “Connect” section above (the earphones do not support
simultaneous connection with two phones).
Tips:
- If the automatic reconnection fails, please reestablish the Bluetooth connection manually or put the earphones back into the charging case for more than 15 seconds and open the charging case – the earphones should reconnect automatically.
- Due to the characteristics of the Bluetooth earphones, the electromagnetic waves in your area may interfere with the connection, turning the earphones silent or disconnecting them.
Power ON/OFF
With the earphones into the charging case:
- Open the charging case – the earphones will power on.
- Close the charging case – the earphones will power off.
Earphones functions
1. Music playing mode
- With the earphones in music playing mode, double tap the right earphone to pause and resume playback.
- When you remove an earbud from your ear while listening to music, the music will automatically pause.
- To resume playback, put the earphone back in your ear.
- When using only one earbud, double tap the earphone to play and pause music (please make sure the other earbud is into the charging case, with the case closed for more than 3 seconds).
2. Voice assistant
When the earphones are in music playing mode or in standby, double tap the
left earphone to awake your voice assistant.
3. Hands-free call mode
Double-tap any earphone to answer and redouble-tap to hang up.
Tips:
Please activate the voice assistant on your mobile phone before using the
earphones’ voice assistant function.
Voice commands
Use these simple voice commands below to control your music and hands-free calls:
Restore to factory settings
1. Restore to factory settings
- Put both earphones into the charging case and keep the cover open.
- Press the button on the back of the charging case for 10 seconds until the red light start flashing. When the green light blinks twice, the factory settings are successfully restored.
2. Automatic restart
Keep the earphones inside the charging case for 15 seconds, then open the case
and the earphones will be restarted automatically. Please make sure that both
earphones are connected successfully with your phone before getting them out
of the charging case.
Charging
1. For the earphones
When the earphones are connected to the mobile phone, the status bar will
display the earphones’ battery autonomy (function supported by 80% of the
mobile phones in the market).
2. Charging the earphones
- Put the earphones into the charging case and the green light will flash, indicating that the earphones have entered charging state.
- When the charging case is opened, if the light is flashing red, the battery is low; when the light turns green, the battery is charged.
- If you press the button on the back of the charging case and the light flashes red, the battery is low; if the light is green, the battery is charged.
3. Charging the charging case
Using the supplied charging cable, plug the Type-C connector into the charging
case and the USB-A connector into a power supply or a certified wall charger.
When the light is red, the battery is charging. When the light turns green,
the charging case is fully charged.
FAQ
Headset cannot be searched, or it disconnects during using
- Do not exceed the Bluetooth connection range.
- Check the battery status of your earphones as well as the battery of the charging case.
- Put the earphones into the charging case, close the case and open it after 15 seconds – the earphones will automatically connect with the phone.
- If the above steps do not solve the issue, put the earphones into the charging case, keep the cover open and long press the button on the back of the charging case for 10 seconds. When the light flashes red and then flashes green, the factory settings have been successfully restored. Long press the button until the blue light flashes, search for “Tellur Ambia” and pair it again with your phone (for iPhone users, please delete the previous connection before pairing again).
Distorted sound
- Adjust the location of your phone and the earphones to avoid any interference from walls or your body.
- Put the earphones into the charging case, close the case and open it after 15 seconds – the earphones will automatically connect with the phone.
- If these steps do not solve the issue, restore the factory settings (as explained above).
Tips: Due to the characteristics of the Bluetooth earphones, the electromagnetic waves in your area may interfere with the connection, turning the earphones silent or disconnecting them. Please avoid using the earphones in such environments.
Tap control function does not work
To avoid accidental touch, the tap control function will only be available
after 3 seconds from the moment you put the earphones into your ear.
When using only the left earbud, with the right earbud kept in the charging case, if you keep the charging case open, the two earbuds will remain connected and the tap function on the left earbud will awake the voice assistant. If you close the charging case, the left earbud will switch to “single ear mode” and the tap function will control music playback (play/pause).
When answering an incoming call by tapping the earphones, the sound is outputted through the earphones. When answering an incoming call by sliding the phone’s screen, some mobile phones output the sound through the phone’s speakers, others output the sound through the earphones.
Different mobile phones will behave differently based on the logical design of their system. All mobile phones will output the sound through the earphones when answering an incoming call by tapping the earphones. However, if you answer an incoming call by sliding the phone’s screen, some mobile phones will output the sound through the phone’s speakers due to different logic processing.
Declaration of conformity
We, ABN SYSTEMS INTERNATIONAL S.R.L., Bucharest, Sector 1, Marinarilor street, nr. 31, we declare on own responsibility that the products below:
Does not endanger life, health, work safety, does not have a negative impact on the environment and corresponds to the standards stated in the manufacturer’s declaration of conformity.
The products are compliant with the following standards and / or other normative documents:
RED – 2014/53/EU
Applied standards:
ETSI EN 301 489-1 V2.2.0:2017
ETSI EN 301 489-17 V3.2.0:2017
EN 55032:2015
EN 55035:2017
EN 61000-3-2:2014
EN 61000-3-3:2013
ETSI EN 300 328 V2.1.1:2016
EN 62479:2010
EN 62368-1:2014+A11:2017
RoHS – 2011/65/EU
The product bears CE mark, applied in 2020.
Name: George Barbu
Function: General manager
Place and date: Bucharest, 22-05-2020
Signed:
Disposal and recycling information
The crossed-out wheeled-bin symbol on your product, battery, literature or
packaging reminds you that all electronic products and batteries must be taken
to separate waste collection points at the end of their working lives; they
must not be disposed of in the normal waste stream with household garbage. It
is the responsibility of the user to dispose of the equipment using a
designated collection point or service for separate recycling of waste
electrical and electronic equipment (WEEE) and batteries according to local
laws. Proper collection and recycling of your equipment helps ensure EEE waste
is recycled in a manner that conserves valuable materials and protects human
health and the environment, improper handling, accidental breakage, damage,
and/or improper recycling at the end of its life may be harmful for health and
environment.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>