LiGHTPRO 179S Castor 8 Spike Light User Manual
- June 9, 2024
- LiGHTPRO
Table of Contents
LiGHTPRO 179S Castor 8 Spike Light
**Castor 8 179S User manual
**
Produced by
THE NETHERLANDS+31 (0)88 43 44 517
[email protected]
WWW.LIGHTPRO.NL
Thank you for purchasing the Lightpro Castor 8.
This document contains the required information for correct, efficient and
safe use of the product. Consult the user manual of your transformer for more
information about the installation and connection of your lighting plan or
visit our website www.lightpro.nl
Read the information in this manual carefully before using the product. Keep
this manual near the product for consultation in the future.
The system
PRODUCT DESCRIPTION
The Lightpro Castor 8 is an LED spot for outdoor use. The fixture can be mounted on a solid surface or placed in the ground with the supplied spikes. This product may only be used as outdoor lighting in combination with the Lightpro 12-volt system. Any alterations made to the product may have consequences for the safety, guarantee and correct functioning of the product and/or other parts of the system.
SPECIFICATIONS
- Product Lightpro Castor 8
- Article number 179S
- Light source LED 8W AC/DC 12V
- Power (max) 8W
- Luminous flux (max) 80 – 800 lm
- Light colour 3.000K
- Average lifetime 25.000
- Dimensions (H x B x W) 130 x 60 x 120 mm
- Protection class IP44
- Ambient temperature -20 °C to 50 °C
- Cable length 1m
- Dimmable Yes, with built-in dimmer
- Light source Not replaceable
- On/off 10.000
PACKAGING CONTENT
[Figure A]
- Fixture Castor 8
- Ground spike
- Screw
- Plug
- Lightpro connector
- Hex key (large)
- Hex key (small)
Check if all parts are present in the packaging. For questions about parts, service, and any complaints or other remarks, you can always contact us. E-mail: [email protected].
INSTALLATION
Option 1 : placement on a fixed underground or mounting to a wall
[Figure B]
- Remove the screw from the base using the included large hex key (Figure A [6]).
- Remove the fixture from the base.
[Figure C]
- Install the base onto the underground with the included screw.
- If necessary, drill a hole in the underground and use the included plug.
[Figure D]
-
Place the fixture in the base.
Place the screw in the base. -
Put the fixture in the desired position.
-
Fasten the screw using the included large hex key
(Figure A [6]).
Option 2: placement in the ground [Figure E]
- Place the spike underneath the base.
- Properly fasten the spike.
- Put the fixture in the desired position.
- Fasten the screw using the included large hex key (Figure A [6]).
- Place the fixture in the ground.
DIMMER FUNCTION
The fixture is equipped with a built-in dimmer. The light output can be set to
6 different levels.
[Figure F]
- Push the button to set the desired light output
INSTALLATION OF THE LIGHTS
- Install the products in the desired position and lay the cables so they can be comfortably connected to the transformer or main cable.
- If products are provided with a drain hole for water, this hole must be pointing downwards.
- Use non-corrosive fixing materials (supplied as standard) if you want to bolt the products down.
- Connect the lights to the main cable by using the connector as shown in figure on page 5.
- Consult the manual of your transformer for more information.
SAFETY
-
Always fit this product so that it can still be accessed for servicing or maintenance. This product must not be permanently embedded or bricked in.
-
Turn off the system by pulling the plug of the transformer from the socket for maintenance.
-
Regularly clean the product with a soft, clean cloth. Avoid abrasives that can damage the surface.
-
Clean products with stainless steel parts with a stainless steel cleaning agent once per six months.
-
Do not use a high pressure washer or aggressive chemical cleaning agents when cleaning the product. This can cause irreparable damage.
-
Protection class III: this product may only be connected to safety extra-low voltage up to a maximum of 12 Volt.
-
This product is suitable for outside temperatures of:
- – 20 to 50 °C.
-
Do not use this product in areas where combustible gases, fumes or liquids may be stored.
-
This product meets the EU standards for health, safety and environmental protection.
-
For questions about parts, service, any complaints or other matters, you can contact us at any time.
E-mail: [email protected] -
Discarded electrical equipment must not be put in the household waste. If possible, take it to a recycling company. For details of recycling, contact a municipal waste processing company or your dealer.
-
5 year warranty – visit our website at lightpro.nl for warranty conditions.
THE NETHERLANDS | WWW.LIGHTPRO.NL