LiGHTPRO 30 R1 150D Onyx 30 R1 IP67 Deck Light User Manual

: June 9, 2024
: LiGHTPRO

Table of Contents

Onyx
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LiGHTPRO 30 R1 150D Onyx 30 R1 IP67 Deck Light

Onyx

30 R1 150D

60 R1 151D

60 R3 153D

60 R4 154D

90 R1 156D

LiGHTPRO 30 R1 - 12 Volt LiGHTPRO
logo1

User manual

MI3845-20211123

A

[1] [2]

Onyx 30 R1 [150D]

Onyx 60 R1 [151D] [3]

Onyx 60 R3 [153D]

Onyx 60 R4 [154D]

Onyx 90 R1 [150D]

B

Onyx 30: ø 30 Onyx 60: ø 60 Onyx 90: ø 90

C

|

CLEAR

| OPAL|

STAR

---|---|---|---

Onyx 30

|

GLASS
RUBBER

|

GLASS
RUBBER
OPAL

|

GLASS
RUBBER
STAR

Onyx 60|

GLASS+
RUBBER

|

GLASS+
RUBBER
OPAL

|

GLASS+
RUBBER
STAR

Onyx 90

|

GLASS
RUBBER

|

GLASS
OPAL
RUBBER

|

GLASS
STAR
RUBBER

GLASS| | |

LiGHTPRO Onyx - The system

The system
Transformer (144A/145A)
Connection to transformer
Connector Type Y (143A)
JUST TURN IT!
Connection to make a branch
Connector Type F (137A)
Connector Type M (138A)
Just twist and connect!

ATTENTION

LiGHTPRO Onyx - Removing or replacing the filter

a) RING
b) GLAS
c) FILTERS
d) GEHÄUSE

Take the following steps when removing or replacing the filter:

Never use two filters simultaneously.
Ensure that the housing is clean and dry before you turn the ring in the housing. The ring must be able to be tightened properly and sufficiently.
Put the ring straight on top of to the body. Make sure at the beginning that the ring is horizontal before turning.

The packaged Onyx has the opal (white) filter built-in.

For questions about parts, service, complaints or other issues you can contact us by sending an email to info@lightpro.info

Onyx

User manual

Thank you for purchasing the Lightpro Onyx.
This document contains the required information for correct, efficient and safe use of the product. Consult the user manual of your transformer for more information about the installation and connection of your lighting plan or visit our website www.lightpro.nl

Read the information in this manual carefully before using the product. Keep this manual near the product for consultation in the future.

PRODUCT DESCRIPTION

The Lightpro Onyx is an LED spot for outdoor use. The fixture can be installed in a fixed underground.
This product may only be used as outdoor lighting in combination with the Lightpro 12-volt system. Any alterations made to the product may have consequences for the safety, guarantee, and correct functioning of the product and/or other parts of the system.

SPECIFICATIONS

Product	Lightpro Onyx
Article number	Onyx 30 R1 – 150D

Onyx 60 R1 – 151D
Onyx 60 R3 – 153D
Onyx 60 R4 – 154D
Onyx 90 R1 – 156D
Light source| Onyx 30 – Led 0,5 W AC/DC 12V
Onyx 60 – Led 1 W AC/DC 12V
Onyx 90 – Led 1,5 W AC/DC 12V
Power (max)| Onyx 30 – Led 0,5 W
Onyx 60 – Led 1 W
Onyx 90 – Led 1,5 W
Luminous flux (max)| Onyx 30 – 4 lm
Onyx 60 – 23 lm
Onyx 90 – 60 lm
Light colour| 2.700K
Average lifetime| 25.000
Dimensions (H x Ø)| Onyx 30 – 41 x 45 mm
Onyx 60 – 42 x 47 mm
Onyx 90 – 43 x 105 mm
Protection class| IP67
Ambient temperature| -20 °C to 50 °C
Cable length| 1m
Dimmable| No
Light source| Not replaceable
On/off| 10.000

PACKAGING CONTENT

[Figure A]

Fixture Onyx 30 / Onyx 60 / Onyx 90
Lightpro connector 137a
Additional lenses

Check if all parts are present in the packaging. For questions about parts, service, and any complaints or other remarks, you can always contact us.
E-mail: info@lightpro.nl.

INSTALLATION

[Figure B]

Install the products in the desired position and lay the cables so that they can be comfortably connected to the transformer or cables.
If products are provided with a drain hole for water, this hole must be pointing downwards.
Use non-corrosive fixing materials (supplied as standard) if you want to bolt the products down.
Connect the lights to the main cable by using the connector as shown on page 5.
Plug the plug of the transformer into the wall socket (230 Volt 50 Hz).

Proceed as follows if the lamps do not light after you have followed the above instructions:

Turn the power off.
Check whether all plugs have been connected properly.
Check the light source(s) and replace them if necessary.
Check the transformer and the fuse (if applicable, and have them circuit-tested if necessary).
Check whether cables have been damaged.
Turn the power back on.

REPLACEABLE LENS

[Figure C]

Note: The rubber ring must be completely clean before replacing the glass because of the water resistance.

INSTALLATION OF THE LIGHTS

Install the products in the desired position and lay the cables so they can be comfortably connected to the transformer or main cable.
If products are provided with a drain hole for water, this hole must be pointing downwards.
Use non-corrosive fixing materials (supplied as standard) if you want to bolt the products down.
Connect the lights to the main cable by using the connector as shown in figure on page 5.
Consult the manual of your transformer for more information.

SAFETY

Always fit this product so that it can still be accessed for servicing or maintenance. This product must not be permanently embedded or bricked in.
Turn off the system by pulling the plug of the transformer from the socket for maintenance.
Regularly clean the product with a soft, clean cloth.
Avoid abrasives that can damage the surface.
Clean products with stainless steel parts with a stainless steel cleaning agent once per six months.
Do not use a high pressure washer or aggressive chemical cleaning agents when cleaning the product.
This can cause irreparable damage.
Protection class III: this product may only be connected to safety extra-low voltage up to a maximum of 12 Volt.
This product is suitable for outside temperatures of:
-20 to 50 °C.
Do not use this product in areas where combustible gases, fumes or liquids may be stored.

This product meets the EU standards for health, safety and environmental protection.

For questions about parts, service, any complaints or other matters, you can contact us at any time.
E-mail: info@lightpro.nl

Discarded electrical equipment must not be put in the household waste. If possible, take it to a recycling company. For details of recycling, contact a municipal waste processing company or your dealer.

5 year warranty – visit our website at lightpro.nl for warranty conditions.

LiGHTPRO 30 R1 - 12 Volt

LiGHTPRO logo1