Ksix BXLEDTV01 COLORLED TV LED Strips User Manual
- June 9, 2024
- KSIX
Table of Contents
Ksix BXLEDTV01 COLORLED TV LED Strips
Technical information
LED: 5050RGB
LEDs per meter: 30 pcs per meter
Output power: 5W/m
Working voltage: DC5V
Operating distance: 8-10m (without barriers)
Working temperature: -20 ±45°C
Illumination angle: 120°
Dimensions: 53 cm (per strip)
Lumens: 12-15 lm per LED
In the box
- 6 TV led strips
- 1 remote controller
- 1 infrared receiver (USB cable)
- 4 spare joints
- 5 joint cables
- 6 clips
- 1 user manual
Installation
-
The LED strips shall be stuck to the back of the TV
-
Clean the back of the TV with a dry cloth
-
Remove the tape stuck to the back of the strip
-
Stick the strip to the back of the TV
-
Use the USB cable to connect the strip to the TV
-
Remove the remote control insulation pad before using it
Each LED strip incorporates a double-sided tape so that it can be attached to
your TV.
Please remove the double-sided tape protector carefully and avoid peeling the
adhesive tape so the strip. The LED strip will not stick to the TV frames if
you remove the tape completely.
How to connect the strips?
First, connect the receiver to the strip with a short 4-pin connector (spare joints).
To connect strips that shall be placed separately, use a long 4-pin connector (joint cables)
To connect strips that shall be placed together, use a short 4-pin connector (spare joints).
Note:
- Please, note that the sign “+” indicates the direction in which the strips shall be connected. When connected, the “+” sign of both strips must point at the same direction.
- Please, do not stick the strips to the TV ventilation area.
FAQs:
The LED strip does not light up once the receiver has been connected and powered on:
- Check the power input. Please use the supplied USB cable or any other equivalent power source. The voltage must not exceed 5V.
- Check if the receiver and the strip are properly connected. Confirm all the components have been connected properly.
- Check if the remote control is switched on.
The LED strip is on, but the remote controller is not working or the LED strip does not respond:
- Check if the insulation pad has been removed from the remote control.
- Check if the battery of the remote control has been installed properly.
- Check if the distance between you and the receiver does not exceed 5m and if the remote controller is pointing the receiver.
- Check if batteries need to be replaced.
Maintenance recommendations
- Regularly clean the product with a dry cloth. The product must be disconnected or switched so when you clean it.
- Keep the connectors and/ or ports free from dust, lint, etc. to prevent improper connections.
- Avoid breaking the device. Do not put objects over it or bend it too strong.
- If the product includes a cable do not bend it too strong and do not pull from it to unplug the product.
- Do not wet the product. Keep it always in a dry place, away from humidity.
- When not using the product, store it in a place free from dust, dirt, lint, liquids, etc.
- If water or other liquids enter the product interior, unplug it immediately from any attached power source or device it is connected to.
- Avoid dropping or hitting the product. It might be damaged.
- Do not use the product for anything other than its intended use.
- Please recycle the product in accordance with local environmental laws and regulations.
Safety information
Please read the following instructions before using the device for the first time:
- When you use device keep it away from heat sources (fire) and from humidity sources (water and other liquids).
- If the product is wet or damaged do not us it.
- Do not use the product with wet hands.
- Do not leave the product in contact with flammable materials.
- Do not expose the product to high temperatures (for example: inside a car during hot weather)
- Do not throw the product into fire.
- Keep the product away from children.
- Disconnect or switch so the product if you are not going to use for a long period of time.
- Do not use the device if you perceive any visible defects.
- Do not attempt to open or puncture the product. You might damage it.
- Do not use the product with incompatible devices.
- Do not dismount or modify the product. These actions will invalidate the Warranty
Legal Note
Hereby, Atlantis Internacional S.L. declares that this product is in
compliance with the essential requirements and other relevant provisions of
Directive 2014/53/EC.
The features and functions described in this manual are based on tests made by
Atlantis Internacional S.L. It is the user’s responsibility to examine and
verify the product after its purchase. Atlantis Internacional S.L. is not
responsible and will never be liable for any personal loss or injury,
economical loss, material loss or any damage due to misuse, abuse or improper
installation of the product.
For electronical devices with Bluetooth: Atlantis Internacional S.L. is not
responsible and will never be liable for any function, communication and
connection failure between the product and Bluetooth enabled devices.
Electronic and electrical devices disposal
This symbol indicates that electrical and electronic equipment is to be collected separately.
- This product is designated for separate collection at an appropriate collection point. Do not dispose of as household waste.
- The final price of this product includes the cost necessary for the correct environmental management of the generated waste.
- If the equipment uses batteries, they must be removed from the equipment and disposed in an appropriate collection center. If the batteries cannot be removed, do not attempt to do it yourself since it must be done by a qualified professional.
- Separate collection and recycling helps conserve natural resources and prevent negative consequences for human health and the environment that might result from incorrect disposal.
- For more information, contact the retailer or the local authorities in charge of waste management.
CE Declaration of Conformity
We hereby declare that the product (s) listed below satisfies the provision for CE-marking according to the following European directive(s):
IEC 62321-1:2013
IEC 62321-3:2013
IEC 62321-4:2017
IEC 62321-5:2013
IEC 62321-6:2015
IEC 62321-7:2015
IEC 62321-7-2:2017
EN 62321-8:2017
Article: BXLEDTV01
EAN: 8427542120966
Features:
INPUT: 5V1.5A
OUTPUT: 5V1.4A
Manufacturer:
ATLANTIS INTERNACIONAL, S.L.
Address:
Carrer del Crom, 53, 08907 L’ Hospitalet de Llobregat, Barcelona (Spain)
Place and date of the declaration:
L ’Hospitalet de Llobregat, November, 1st 2021
Nico Broder
General Manager
Documents / Resources
| Ksix
BXLEDTV01 COLORLED TV LED
Strips
[pdf] User Manual
BXLEDTV01 COLORLED TV LED Strips, BXLEDTV01, COLORLED TV LED Strips, TV LED
Strips, LED Strips, Strips
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>