ASRock X600TM-ITX Motherboard Installation Guide

ASRock X600TM-ITX Motherboard

Specifications:

• Model: X600TM-ITX
• Part Number: 15G067050xxxx V1.0
• Form Factor: ITX
• CPU Socket: X600TM
• Chipset: Realtek RTL8111H (Optional: Realtek RTL8111FP)
• Memory: DDR5 SO-DIMM, 4 slots
• Expansion Slots: PCIe x16
• Audio: Realtek HD Audio
• LAN: RJ-45 Port
• Storage: SATA3, M.2 SSD
• USB Ports: USB 3.2 Gen1, USB 3.2 Gen2
• Video Output: HDMI, Display Port

Product Usage Instructions

Precautions:

Before installing or changing any components, ensure to:

• Unplug the power cord from the wall socket.
• Avoid static electricity by grounding yourself.

Motherboard Layout:

The motherboard layout includes various components such as CPU socket, chipset, memory slots, expansion slots, audio ports, LAN port, storage connectors, USB ports, and video output ports.

Onboard Headers and Connectors:

• ATX 19V Power Connector: Connect an ATX 19V power supply.
• SATA Connectors: Support SATA data cables for internal storage devices.
• SATA Power Connectors: Connect SATA power cables.
• USB Headers: USB 3.2 Gen1 and USB 2.0 headers available.
• FPD Brightness Header: For backlight control interface.

Jumper Settings:

Refer to the manual for jumper settings related to panel voltage selection and backlight inverter voltage selection. Ensure correct settings to prevent damage.

Panel On/Off Header:

This header is used for panel on/off functionality. Refer to the manual for detailed instructions on its usage.

BIOS ROM:

The BIOS ROM contains essential system information and settings. Avoid tampering with it unless necessary.

FAQ:

• Q: What should I do if I encounter static electricity while handling components?
  A: Ground yourself by touching a metal surface before touching any components to discharge static electricity.

• Q: How do I connect the ATX 19V power supply?
  A: Connect the ATX 19V power supply plug to the designated connector on the motherboard ensuring correct orientation.

• Q: How many USB headers are available on this motherboard?
  A: There is one USB 3.2 Gen1 header and one USB 2.0 header on this motherboard.

Take note of the following precautions before you install motherboard components or change any motherboard settings

1. Unplug the power cord from the wall socket before touching any components.
2. To avoid damaging the motherboard’s components due to static electricity, NEVER place your motherboard directly on the carpet or the like. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle the components.
3. Hold components by the edges and do not touch the ICs.
4. Whenever you uninstall any component, place it on a grounded anti-static pad or in the bag that comes with the component.
5. When placing screws into the screw holes to secure the motherboard to the chassis, please do not over-tighten the screws! Doing so may damage the motherboard.

Package Contents

• X600TM-ITX Motherboard (Thin Mini-ITX Form Factor)
• X600TM-ITX Quick Installation Guide (Optional)
• 1 x Thin-Mini ITX I/O Shield (Optional)
• 1 x Mini ITX I/O Shield (Optional)
• 1 x Serial ATA (SATA) Data Cable (Optional)
• 1 x SATA Power Cable (Optional)
• 2 x Screws for M.2 Sockets (M2*2) (Optional)
• 1 x Screw for WiFi Module (M2*2) (Optional)
• 1 x Standoff for M.2 Socket (Optional)

The terms HDMI® and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

Motherboard Layout

•    6.7” x 6.7”

CPU| •    Supports AMD Socket AM5 RyzenTM 8000 and 7000 Series Processors

•    Supports CPU up to 65W

•    4+1+1 Power Phase design

Chipset| •    AMD X600
Memory| •    Supports 2 x DDR5

SO-DIMM Slots, Max. 96GB

Expansion Slot| •    1 x M.2 Socket (Key E), supports type 2230 WiFi/BT module
Audio| •    Realtek ALC269
LAN| Realtek RTL8111H

• (Optional) Realtek RTL8111FP

Storage| •    1x Hyper M.2 (2260/2280) PCIe Gen4x4

•    1x Hyper M.2 (2280) PCIe Gen4x4

•    2 x SATA 6Gb

Rear USB| •    1 x USB 3.2 Gen2 Type-A

•    1 x USB 3.2 Gen2 Type-C

• (Optional) 2 x USB 3.2 Gen2 Type-A

•    2 x USB 3.2 Gen1

Video Output| •    1 x DisplayPort 1.4 (DP2)

• (Optional) 1 x D-Sub

•    1 x HDMI: HDMI2 (Internal)

•    1 x HDMI: HDMI1 (Rear)

• (Optional) 1 x DisplayPort 1.4 (DP1) + 1 x HDMI: HDMI1 (Rear)

Onboard header| * (Optional) 1 x Onboard TPM 2.0 (IN- FINEON SLB9672 or NUVOTON NPC- T750AADYX)

•    1 x Chassis Intrusion Header

•    1 x Panel Voltage Selection Header

•    1 x Backlight Inverter Voltage Selection Header

•    1 x FPD Brightness Header

•    1 x Panel On/Off Header

•    1 x LVDS Connector

•    1 x CPU Fan Connector (4-pin)

• The CPU Fan Connector supports the CPU fan of maximum 1A (12W) fan power.

•    1 x 4 pin 19V Power Connector

•    1 x Front Panel Audio Connector

•    1 x Internal Speaker Header (4-Pin)

•    1 x Digital MIC Header

•    2 x SATA Power Connectors

•    1 x USB 2.0 Header (Supports 2 USB 2.0 ports)

•    1 x USB 3.2 Gen1 Header (Supports 2 USB 3.2 Gen1 ports)

Power| •    1 x DC Jack (Supports 19V DC Power Adapters)
Certifica- tions| •    FCC, CE

•    ErP/EuP ready (ErP/EuP ready power supply is required)

SO-DIMM

I/O Panel

Jumper Cap On/Off

The illustration shows how jumpers are setup. When the jumper cap is placed on the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is “Open”.

Clear CMOS Jumper
CLRMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short the pins on CLRMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time, and user default profile will be cleared only if the CMOS battery is removed. Please remember toremove the jumper cap after clearing the CMOS.

Panel Voltage Selection Header

Backlight Inverter Voltage Selection Header

Warning:
If selected Backlight Power or Panel Power is higher than panel’s spec, it may damage the panel.

Onboard Headers and Connectors

ATX 19V Power Connector
Please connect an ATX 19V power supply to this connector.
The power supply plug fits into this connector in only one orientation.
5 / 6 – Serial ATA3 Connectors
These two SATA3 connectors support SATA data cable for internal storage devices with up to 6.0 Gb/s data transfer rate.
2 / 3 – SATA Power Connectors Please connect a SATA power cables

USB 3.2 Gen1 Header
There is one USB 3.2 Gen1 header on this motherboard

PIN| Signal Name| PIN| Signal Name| PIN| Signal Name| PIN| Signal Name
---|---|---|---|---|---|---|---
1| ID| 6| GND| 11| IntA_P_SSTX-| 16| IntA_P_SSRX –
2| IntA_P_D +| 7| GND| 12| GND| 17| IntA_P_SSRX –
3| IntA_P_D +| 8| IntA_P_SSTX+| 13| GND| 18| Vbus
4| IntA_P_D –| 9| IntA_P_SSTX+| 14| IntA_P_SSRX +| 19| Vbus
5| IntA_P_D –| 10| IntA_P_SSTX-| 15| IntA_P_SSRX +| 20| N/A

USB 2.0 Header
There is one USB 2.0 header on this motherboard.

FPD Brightness Header
This is a header for backlight control interface.

P anel On/Off Header
This header can be used to connect a switch that turns on/off the LVDS panel display’s backlight.

LVDS Panel Connector
This is a LVDS Panel Connector.

CPU Fan Connector
This motherboard provides a 4-Pin CPU fan (Quiet Fan) connector. If you plan to connect a 3-Pin CPU fan, please connect it to Pin 1-3.

Chassis Intrusion Header
This motherboard supports CASE OPEN detection feature that detects if the chassis cove has been removed. This feature requires a chassis with chassis intrusion detection design.

Digital MIC Header
This header can be used to connect a digital MIC.

System Panel Header
Connect the power button, reset button and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

• PWRBTN (Power Button):
  Connect to the power button on the chassis front panel. You may configure the way to turn off your system using the power button.

• RESET (Reset Button):
  Connect to the reset button on the chassis front panel. Press the reset button to restart the computer if the computer freezes and fails to perform a normal restart.

• PLED (System Power LED):
  Connect to the power status indicator on the chassis front panel. The LED is on when the system is operating. The LED keeps blinking when the system is in S1/S3 sleep state. The LED is off when the system is in S4 sleep state or powered off (S5).

• HDLED (Hard Drive Activity LED):
  Connect to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading or writing data.

Internal Speaker Header
Please connect the chassis speaker to this header.

Front Panel Audio Header
This header is for connecting audio devices to the front audio panel.

UEFI Setup

UEFI SETUP UTILITY
You may run the UEFI SETUP UTILITY by pressing or right after you power on the computer, otherwise, the Power-On-Self-Test (POST) will continue with its test routines. If you wish to enter the UEFI SETUP UTILITY after POST, restart the system by pressing + + , or by pressing the reset button on the system chassis. You may also restart by turning the system off and then back on.
Because the UEFI software is constantly being updated, the following UEFI setup screens and descriptions are for reference purpose only, and they may not exactly match what you see on your screen

Main Screen
When you enter the UEFI SETUP UTILITY, the Main screen will appear and display the system overview.

Advanced Screen
In this section, you may set the configurations for the following items: CPU Configuration, Chipset Configuration, Storage Configuration, ACPI Configuration, USB Configuration and Trusted Computing

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>