Dualit 11000 Single and Double Baby Bottle Warmer Instruction Manual

11000 Single and Double Baby Bottle Warmer

Single and Double Baby Bottle Warmer
Instruction Manual & Guarantee

Single Baby Bottle Warmer Double Baby Bottle Warmer

WWW.DUALIT.COM/REGISTER OR BY POST

DON’T FORGET TO REGISTER YOUR PRODUCT

GB-A

A feeding and weaning range designed to make everyday baby life that bit easier.
ORDER THE FULL RANGE AT www.dualit.com
Dualit Limited County Oak Way Crawley West Sussex RH11 7ST +44(0)1293 652 500 info@dualit.com www.dualit.com

IMPORTANT SAFETY PRECAUTIONS
READ ALL INSTRUCTIONS
BEFORE USING THE BABY BOTTLE WARMER.
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
IMPORTANT SAFEGUARDS
· THIS IS AN ATTENDED APPLIANCE. Do not leave unattended during use, unplug after each use (risk of fire if an unattended appliance is left operating or plugged in).
· This appliance must not be used by children younger than 8 years old and persons
with very extensive and complex disabilities. Children aged 8-14 years and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge shall not use this appliance unless they are supervised and have been given instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.
· Cleaning and user maintenance shall not be made by children unless they are older
than 8 and supervised.
· Keep the appliance and its cord out of reach of children less than 8 years old. · Appliances can be used by persons with reduced physical, sensory, or mental
capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
· This appliance is intended for household use only. If the appliance is used improperly
or for professional or semi-professional purposes or if it is not used according to these instructions the Guarantee becomes invalid and Dualit refuses any liability for damage caused.
Before connecting to the Mains Supply · Check that the voltage marked on the appliance corresponds with the supply voltage. · Note: any plug cut from the power supply cord should be disposed of immediately.
Inserting any cut off plug into a 13A socket-outlet is hazardous.

· Never use the plug without the fuse cover fitted. Ensure replacement fuse is the same
current value as the original. Replacement fuses are available and should be ASTA approved to BS1362.
· We recommend that the appliance is plugged into a socket that has no other
appliance connected to it. Failure to do this may cause an overload, trip a circuit breaker, or blow a fuse. Preferably the socket outlet should be protected by a residual current device (RCD).
· Should the light remain illuminated after using the appliance, immediately unplug the
appliance and call Dualit’s Customer Helpline on +44 (0)1293 652 500. Risk of electric shock.
· Do not place the appliance or mains lead on or near any hot surface, hob, gas burner
or in a heated oven. Risk of electric shock and fire.
· To be protected against electrical hazards, fire, and injury to persons, do not immerse
the mains lead, plug or appliance in water or any other liquid. Risk of electric shock.
· Do not operate any appliance with a damaged lead or plug, or after the appliance
malfunctions or has been dropped, damaged, or cracked in any manner. Risk of electric shock and fire.
· To avoid a hazard, if the power cord is damaged it must, for safety reasons, be
replaced by Dualit or an authorised Dualit repairer. Call Dualit’s Customer Helpline on +44 (0)1293 652 500. Risk of electric shock and fire.
· A short power-supply cord is provided to reduce risks resulting from becoming
entangled in or tripping over a longer cord. Risk of fire.
· Do not allow the cable to hang over the edge of a table or countertop. Risk of fire.
· Never tamper with the safety systems. They are included for your personal safety.
Risk of injury.
· Do not misuse the appliance; it is designed for use with milk and food items only. Risk
of injury.
· Do not add boiling liquids or foods into the inner chamber. Risk of sudden steam and
liquid being ejected. Risk of injury.
· Turn the power off via the Control Panel and unplug before opening the Lid. Risk of fire.

· Do not remove or open the Lid while the appliance is switched on. Risk of scalding.

· Switch off the appliance and disconnect from supply before approaching while in use.
Risk of scalding.

· Clean all parts after each use; please refer to the cleaning instructions.

· Do not operate the appliance unless there is water in the Water Bath, see table
below for amounts. Risk of affecting the life of the Bottle Warmer.

Single Bottle Warmer

Double Bottle Warmer

45ml of water

90ml of water

· Do not operate on an uneven surface. The machine must only be operated on a flat,
horizontal surface. Risk of injury.

· Do not use in a bathroom or outdoors. Risk of electric shock.

· If it is not used according to these instructions the Guarantee becomes invalid and
Dualit refuses any liability for damage caused.

· Do not store or use in an appliance garage or under cupboards. Risk of fire.

· Ensure that the appliance is assembled with all components in place before turning on.
Risk of scalding.

· For safety reasons keep hands and utensils out of the Water Bath while switched on
to reduce the risk of injury to persons or damage to the appliance. Risk of scalding.

· Do not remove items from the appliance while it is switched on. Risk of scalding.

· Cautions: Product surface, Element and appliance interior are subject to residual
heat after use. Risk of scalding.

· Hot Water Hazard. Avoid direct contact with hot water. Unplug the appliance
from the mains to allow to cool before cleaning, maintaining, moving or storing. For
details, please refer to the cleaning section. Risk of scalding.

· Warning – steam hazard: When boiling, hot steam will be emitted from the
appliance. Scalding may occur if you are within 400mm of the steam vent.

· Scalding may occur if the lid is opened during a cycle.

Before returning any product under this Guarantee, please check that: · You have followed the product instructions correctly. · Your mains electricity supply is functional. · The defect is not due to a blown fuse.
If you wish to claim under this guarantee you should: · Send the product, postage or carriage paid, to the dealer from whom it was
purchased or to Dualit direct. · Ensure that the product is clean and packed carefully (preferably in its original
carton). · Enclose details of your name, address and telephone number and when and
where the product was purchased, together with proof of purchase (e.g. a till receipt). · Give exact details of the nature of the defect.
This Guarantee does not cover any other claims whatsoever, including, without limitation, any liability for incidental, indirect or consequential damage, nor does it cover any claims for conversion or modification or for the costs of repair carried out by any third party without the prior consent of Dualit. If replacement parts are fitted to the product this will not extend the period of the Guarantee.
For further advice contact the Dualit customer helpline on +44 (0)1293 652 500 (09:00 to 17:00 Monday to Friday).
Alternatively, email Dualit at info@dualit.com or visit www.dualit.com
Do not throw away the appliance with the normal household waste at the end of its life, but hand it in to an official collection point for recycling. By doing this you help preserve the environment.
INSTRUCTIONS ON ENVIRONMENT PROTECTION Do not dispose of this product in the usual household garbage at the end of its life cycle. Please hand it over to a collection point for the recycling of electrical and electronic appliances. The symbol on the product, the instruction of use or the packaging will inform you about the methods of disposal. The materials are recyclable as mentioned on its marking. By recycling, material recycling or other forms of re- utilization of old appliances you are making an important contribution to protect our environment. Please inquire at the community administration for the authorised disposal location.

SAVE THESE INSTRUCTIONS
In the interest of improving products, Dualit Ltd. Reserves the right to change the product specification without prior notice. All illustrations are for representation only, your model may vary from illustrations shown.
npack the box with care, keeping all the packaging materials until you U
are satisfied everything is present and in working order. Once satisfied remove any tags from the appliance body and recycle the packaging appropriately. Do not remove tags from the cord. You may wish to keep the box to store your appliance.manual included with the warming rack.
GUARANTEE
This appliance is of excellent quality and construction. However, if any defects in materials or workmanship do appear during the relevant guarantee period, we will, at our discretion, either repair or replace the defective parts, free of charge, subject to the terms and conditions of our Guarantee shown below. This Guarantee covers both parts and labour. Carriage is not included. Your Guarantee period is as follows: · 1 year
This Guarantee provides benefits which are additional to, and do not affect, your statutory rights. This Guarantee does not cover the cost of returning the product to the dealer from whom it was purchased or to ourselves. This Guarantee applies only to products sold and located in mainland Great Britain. It does not cover liability in respect of or replacement of plugs, cables or fuses and also does not cover defects due to:
· Failure to use or maintain product in accordance with Dualit’s instructions. · The product being connected to an unsuitable electricity supply. · Accidental damage to or abuse or misuse of the product. · Product modification, except by Dualit or approved agent. · Dismantling of or interference with the product. · Theft or attempted theft of the product.

· Caution: Vents are hot. Risk of scalding.
· This appliance features boil-dry protection. If the appliance overheats, the boil-
dry device will switch off the Element to prevent damage to the appliance. Wait approximately one hour for the appliance to cool down and refill as normal. The appliance is now ready to use again. NOTE: If discolouration of the Element has occurred, this can be easily removed by descaling your appliance.
· Unplug the appliance from the wall socket when not in use or before moving and
cleaning. Risk of fire.
· Do not move the appliance while it is switched on. Risk of scalding.
· When moving the appliance, use both hands and lift holding the Base. Do not touch
hot surfaces. Risk of scalding.
· To disconnect, press the Start/Stop/Standby button, then remove the plug from wall
outlet. Risk of fire.
· Caution: To prevent damage to the appliance, do not use alkaline cleaning agents.
When cleaning, use a soft cloth and a mild detergent. Risk of electric shock
· Do not use a scouring pad or abrasive cleaner on the appliance body. Risk of electric
shock.
· Always pour any remaining water out of the appliance after use, after the appliance
has cooled down and has been unplugged. Risk of Contamination.
· The use of accessory attachments is not recommended by Dualit and may result in
fire, electric shock, or injury to persons.
· Always check the temperature of milk and food before feeding your baby. To test
milk, shake drops onto the inside of your wrist. To test food place a metal spoon to the bottom of the container, wait 5 seconds and withdraw the spoon, rest the spoon against your lips. Do not heat food for longer than is required and stir well before serving. Risk of scalding.
Descale Regularly
· Do not operate the appliance if filled with descaling solution.
This can cause damage to the machine and burning/scalding risk to user.

KNOW YOUR BABY BOTTLE WARMER
LID

RACK ELEMENT COVER WATER BATH

CONTROL PANEL BASE

POWER CORD

FUNCTIONS

ICON

FUNCTION

Milk Warming

Fast Milk Warming (20% quicker at 9oz)

Defrosting

DESCRIPTION
Evenly warms the milk to approximately 32-42°C. The perfect temperature for your baby. Recommended setting for milk warming.
Quickly and evenly heats larger volumes of milk to approximately 30-44°C. Perfect when you are in a rush with older babies. Caution; bottle/jar will be hot if left in the Milk Bottle Warmer after the program has finished. Caution: For Double Milk Warmer milk will be too hot if bottles contain mixed levels of milk/food.
Defrosts frozen milk or baby food.

Food Warming

Heats food up to 60°C.

T IN USE

SETTING UP
Read and follow these instructions before using your Baby Bottle Warmer. This is an attended appliance. Do not leave unattended during use, unplug after each use (risk of fire if an unattended appliance is left operating).

Never remove the lid while the Baby Bottle Warmer is operating. (Function light is illuminated). Warning: Hot water and steam may cause injury and burns; keep hands away from hot surfaces and steam vents. Risk of scalding.

1

2

3

UNPLUG

WHEN NO

Register your product at Dualit. com this will only take 60 seconds; you will need the product model and serial numbers that are on the rating label on the base of the product.

Position the Baby Bottle Warmer Base on a flat dry surface away from sources of heat, as close to the wall socket as possible. Do not store or use the Baby Bottle Warmer under kitchen cabinets, in an appliance garage, close to curtains or flammable material as it will emit steam from the steam vent in the Lid. Caution: Do not cover vent, risk of fire.

Ensure that the Baby Bottle Warmer is placed on a heat resistant work surface. Do not operate on a tray that can collect water. Risk of electric shock. Do not let the cord hang over the edge of work surfaces or touch hot surfaces.

USING YOUR BABY BOTTLE WARMER
Before the first use or after a long period of no use, fill and operate the Baby Bottle Warmer empty on a Sterilising function. Do not submerge the Base, Power Cord or plug as there is a risk of electric shock and permanent damage to the appliance. Caution: Never select a function when there is no water in the Water Bath. Only use when water is in the Water Bath.Too little water may affect the life of the Baby Bottle Warmer. Always shake the bottle/stir the food to avoid hot spots. Check the temperature before serving, failure to do so will result in a risk of scalding baby.

1

2

3

7

8

BEEP!

9

CLEANING AND CARE

Before cleaning make sure the machine is switched off, unplugged and allowed to cool. Dualit recommends cleaning your baby bottle warmer after every use.

00

Do not submerge the Base, Power Cord or plug into water or other liquid, or position under a water tap. Do not use sharp, abrasive or aggressive cleaning agents, bleach or scouring pads to clean the Baby Bottle Warmer.

The use of such cleaning implements may affect the life of the Baby Bottle Warmer.

Press the Start/Stop/Standby button to start the cycle. Note: Never start a function without water in the Water Bath, this may affect the life of the Baby Bottle Warmer.
10

When the function ends the Baby Bottle Warmer will beep three times. Caution: Pressing the Start/ Stop/Standby button will end the heating cycle early and the milk/ food will not be heated to the correct temperature.
101

Immediately remove the bottle/ jar from the Baby Bottle Warmer at the end of the cycle to prevent overheating the food/milk. Caution: During Fast Milk Warming function, bottle/jar and Water Bath will be hot; risk of scalding. Always check milk/ food temperature before giving to your baby.
12

1

2

3

Unplug the Baby Bottle Warmer from Remove the Lid and Rack, pouring

the mains and allow to cool down

away any excess water.

completely before cleaning.

Clean all surfaces of the Base, including the Water Bath, Rack and Lid with mild detergent (washing up liquid) and a soft, damp cloth.

Caution: Do not use sharp articles or metal tools to touch the Element as it may cause electric shock. When not in use, clean and dry the Baby Bottle Warmer and store in a cool, dry place.

Always check the temperature before serving. Test milk by placing drops onto the inside of your wrist. Test food by placing a metal spoon to the bottom of the container, wait 5 seconds and withdraw the spoon, rest the spoon against your lip. Failure to do so will result in a risk of scalding baby

Unplug Baby Bottle Warmer when not in use.

Tip away water from the Water Bath after each use and follow cleaning instructions. Note: wait 15 minutes before starting the next function cycle.

STERILISING
Before sterilising, ensure all items have been cleaned with warm, soapy water to remove all milk/food residue. Rinse thoroughly. Separate all items into individual components.

1

2

3

DESCALE REGULARLY
IMPORTANT NOTICE: PRODUCT FAILURE DUE TO THE BUILD-UP OF LIMESCALE IS NOT COVERED BY GUARANTEE.
The Baby Bottle Warmer needs to be descaled regularly. As a minimum, it is recommended that you descale once a month in soft water areas, every 21 days in medium water areas and every 14 days in hard water areas. You can check your water hardness with your water provider. Wear rubber gloves. Do not use on marble surfaces. Do not put descaler bottle on work surfaces. Wipe descaler bottle after use.

1

2

3

Sterilising

CONTROLS

ICON

CONTROLS

Menu button

Used to sterilise bottles, teats, and accessories*. Always thoroughly wash items before sterilising. This function kills 99.9% of bacteria.
DESCRIPTION Toggling between the 5 functions. The function selected will illuminate.

Volume button

Start/Stop/Standby button

DISPLAY ICON

CONTROLS Cycle Time Indicator

Adjusts the volume (Fl. Oz.) of milk/food being heated. This must be set each time a new function is selected. Cycle Time Indicator will automatically change for the selected volume. Adjustable volume ranges between 2oz (58ml) and 9oz (225ml). For switching between starting, stopping and entering standby mode. To switch off unplug.
DESCRIPTION
Indicates how long a cycle will take, once the cycle is started, this will count down to zero in minutes.

Volume Indicator

Indicates the volume of milk/food to be heated. This volume

Single Bottle Warmer corresponds to the amount of milk in one bottle.

Volume Indicator Double Bottle Warmer

If heating 2 bottles/containers, select the volume of one bottle. Both bottles/containers must contain equal amounts. Risk of under heated milk/food if more milk/food is in one of the containers.

*Bottles will be sterile for 24 hours after cycle as long as the lid isn’t removed.

The chart below shows the preprogramed times for each of the warming functions for the corresponding volumes of milk/food being heated for both the Single and Double Bottle Warmer.

+MILK FUNCTIONS WARMING

2 oz (56 ml) 3 oz (85ml) 4 oz (114ml) 5 oz (142ml) 6 oz (170ml) 7 oz (198ml) 8 oz (227ml) 9 oz (225 ml)

5 min 6 min 8 min 9 min 9 min 10 min 11 min 12 min

+FAST MILK WARMING
5 min 6 min 6 min 8 min 8 min 9 min 10 min 10 min

DEFROSTING
TIME 5 min 10 min 15 min 19 min 20 min 20min 21 min 22 min

++FOOD WARMING 1g +1ml of water
12 min 13 min 20 min 23 min 24 min 25 min 31 min 32 min

STERILISING 30 min

Note: Sterilising function always takes 30 minutes.This time cannot be changed.
Always remove bottle/jar from the warmer as soon as the cycle has finished. Failure to do so will result in a risk of scalding baby. + Always gently shake milk bottle to avoid hot spots and check the temperature every time by placing drops onto the inside of your wrist before serving. Failure to do so will result in a risk of scalding the baby. ++ Always ensure milk/food is thoroughly heated. Stir any food halfway through the cycle to avoid hot spots. Test food by placing a metal spoon to the bottom of the container, wait 5 seconds and withdraw the spoon, rest the spoon against your lips. Caution: Risk of food poisoning.

Wash the Lid and Rack with warm, soapy water and rinse thoroughly. Clean all surfaces of the Base, including inside the Water Bath with washing up liquid and a soft, damp cloth. Note: Do not use sharp, abrasive or aggressive cleaning agents, bleach, or scouring pads to clean the Baby Bottle Warmer. The use of such cleaning implements may affect the life of the Baby Bottle Warmer.

Fill the Water Bath with water. See table below for amounts and fit the
Rack and Lid.

Sterilisation Water Bath Fill Level

Single Bottle Double Bottle

Warmer

Warmer

45ml of water 90ml of water

Repeatedly press the Menu button
until the Sterilising icon illuminates with a red flashing light, then press
the Start/Stop/Standby button. The
icon light will turn solid. The cycle will finish when the light turns off
and the beep sounds 3 times.

MILK WARMING/FAST MILK WARMING/FOOD
WARMING AND DEFROSTING
Always remove the bottle/jar from the Baby Bottle Warmer immediately at the end of the cycle to prevent the food/milk from overheating. Risk of scalding. Caution: When using the Fast Milk Warming function always check selected bottle volume before starting the cycle, to prevent the food/milk from overheating; risk of scalding. Bottle/ jar and Water Bath will be hot; risk of scalding. Always check milk and food temperature before giving to your baby.

1

2

3

Fill bottle/jar with desired amount of food/milk. Note: Minimum bottle fill
2oz (56ml). Fit the bottle teat and lid.
Warning: Remove lid from any food jar before heating.

Place bottle/jar into the Water Bath Teat facing up. Fill the Water Bath with water, level with the milk/food in the bottle/jar and fit the Lid. The Rack is not required for heating milk/food.

Double Bottle Warmer
Only heat even amounts of milk/ food in each bottle/jar. Risk of scalding if bottle/ jar contain uneven amounts of milk/food.

Water Bath Minimum Fill Level Single Bottle Warmer 120ml of water minimum

Double Bottle Warmer 240ml of water minimum

4

5

6

Plug in the Baby Bottle Warmer to the mains. The appliance will beep to inform you that it is in standby mode.

Repeatedly press the Menu button
until the chosen icon illuminates with a red flashing light.

Repeatedly press the Volume button to select the volume of milk/ food being warmed. The volume is in Fl Oz. If using 2 bottles, select the volume of 1 bottle/container.

With the Lid and Rack removed, pour water into the Water Bath. See table below for amounts. Caution: Adding too much water will slow the steam sterilisation process, too little water will result in unsterilised items and may affect the life of the Baby Bottle Warmer. Do not fill above the top of the Element Cover.

Place the milk bottle facing downwards inside the Water Bath.

Sterilisation Water Bath Fill Level

Single Bottle Double Bottle

Warmer

Warmer

45ml of water 90ml of water

Position the Rack over the bottles, on top of the Base.

4

5

6

Place bottle collars, teats followed by Lids on top.

7

BEEP!

Position the Lid on top of the Rack and plug into mains. Caution: Ensure that the lid is correctly positioned, failure to do so may affect sterilisation performance.
8

Use the Menu button to select Sterilising function. Press the Start/Stop/Standby button to begin the cycle. Note: You do not need to amend the volume for this cycle.
9

00

The Baby Bottle Warmer will beep
3 times to indicate the cycle has finished.

Unplug from the mains when not in use. Do not remove the items from the Water Bath for at least 5 minutes due to residual heat.

Once the Baby Bottle Warmer has cooled down, remove the items, pour away remaining water, and follow cleaning instructions.

Items left within the Baby Bottle Warmer will remain sterile for up to 24hrs, providing the Lid is not removed. Note: wait 15 minutes before starting the next function cycle.

Unplug the Baby Bottle Warmer from the mains and allow to cool down completely before descaling.

Pour 100ml of just-boiled water into the Water Bath, then add 50ml of Kilrock Espresso & Coffee Machine Descaler. This can be purchased on dualit.com. Caution: Be aware of splashing. Risk of scalding and chemical inhalation.

4

5

Leave to stand for 20 minutes.
Tip – To minimise limescale build up in your Baby Bottle Warmer; empty the Baby Bottle Warmer after each use, do not allow water to stand in the Baby Bottle Warmer overnight, use filtered water instead of tap water.

Pour away solution, wipe around the surface with a cloth and rinse well by pouring clean water into the Water Bath.

Rinse the Water Bath a minimum of three times. Failure to do so can cause injury. Do not start any function with descaling solution in it.

TROUBLESHOOTING

TO REPLACE FUSE, REMOVE SILVER LABEL TO ACCESS SCREW.

POSSIBLE CAUSE(S) SOLUTION(S)

MY MILK/FOOD IS TOO HOT OR COLD

You may have selected the incorrect volume for the milk/food being heated.

Ensure that the volume selected is the same as the volume of milk/food being heated in one bottle/container.
Ensure you have selected the correct function. If using the Double Milk warmer, ensure the volume in both bottles/jars is equal.

Your Bottle Warmer may need descaling. Always descale regularly, see Descale Section for how to descale.

MY BOTTLE WARMER ISN’T TURNING ON WHEN I PLUG IT IN

Your Baby Bottle Warmer Press the Start/Stop/Standby button to light up the Control Panel. is in standby mode.

Heating cycle may have been started before water was added to the Water Bath.

Allow to cool for half an hour and try again. Always ensure the correct amount of water is in the Water Bath before starting a cycle.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>