WAC 6011 Path Light Instruction Manual
- June 9, 2024
- WAC
Table of Contents
WAC 6011 Path Light
SAFETY INSTRUCTION
IMPORTANT: NEVER attempt any work without shutting off the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations.
- Place the wall switch in the “OFF” position
- Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch ”OFF” the circuit breaker switch(es) that control the power to the space that you are working on
- Listed wire nuts suitable for wet location.
CAUTION:
All parts must be used as indicated in these instructions. Do not substitute
any parts, leave parts out, or use any parts that are worn out or broken.
Failure to follow this instruction could invalidate the ETL/Celt listing of
this fixture
*Note: Transformer is required to power the fixture. (sold separately)
THIS INSTRUCTIONS APPLY TO THE MODELS BELOW:
Mounting Accessories (included in box)
9” Mounting Stake Qty: 1pc 9000-ST9-BZ
|
Outdoor Rated Wire Nut Qty: 2pcs 7EAC352401
---|---
14” Mounting Stake Qty: 1pc 9000-ST14-BZ
|
Outdoor Rated Wire Nut Qty: 2pcs 7EAC352401
---|---
INSTALLATION
STEP 1:
-
Make sure your main power is off.
-
At the point of installation, mount the stake by placing a piece of wood on the stake and hammering the wood.
Hammer till the bottom of the ring is flush with the ground. -
In the case of hard soil, dig a hole and place the stake in so that the bottom of the ring is flush with the ground.
Fill the rest of the hole with the removed soil and pack it tight to secure the stake. -
Screw the fixture onto the stake provided, leading the wire from the fixture through the wire slot in the stake.
STEP 2: -
Cut the power supply wire from the transformer at the location of the fixture.
-
Separate the power supply wire into two individual wires by lightly pulling on each side so that a couple inches is separated.
-
Strip off ½ inch of the insulating material from each wire and connect one to each of the wires from the fixture using the outdoor rated direct burial wire nuts provided.
STEP 3: -
Screw the fixture onto the stake provided, leading the wire from the fixture through the wire slot in the stake.
-
If desired, bury your wire by digging a small trench. Close the trench by applying an inward force to both sides of the trench.
-
Repeat steps for other fixtures in the same electrical circuit.
-
Turn the main power supply back on and make sure the fixtures light up
INSTALLING THE SURFACE MOUNT ACCESSORY
Soft-soaped Installation:
- Attach the three removable spikes to the surface mount accessory by screwing them in.
- Using a piece of wood to buffer the impact, hammer the assembled mount into the soil till the bottom of the surface mount accessory is flush with the ground.
- Lead your wire through the wire slot and screw in your fixture.
- Connect fixture wires to power supply wires as normal using the outdoor rated direct burial wire nuts provided.
Hardscape Installation:
- Mount the accessory to the surface using No. 10 Philips head screws that are at least half an inch long.
- If mounting on concrete or something similar, first use plastic anchors sized for No. 10 screws.
- Create a route underneath the accessory for your wire to travel through.
- Lead your wire through the created route and screw your fixture onto the surface mount accessory
Installing Fixture Caps:
Thread the fixture cap into the stem body by rotating it clockwise.
Customer Support
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
WAC Lighting retains the right to modify the design of our products at any time as part of the company’s continuous improvement program. 3
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>