Nalloy LLC VG8HYF Radio Module Instructions

Nalloy LLC VG8HYF Radio Module

Radio Module Information

• FCC ID: 2AVOB-VG8HYF

• Model: VG8HYF

• Operating frequency: 902.4-927.6 MHz

• Maximum output power: 14dBm (Conducted at
  antenna port)

• Antenna: PCB antenna, 5.2 dBi.

• The device complies with FCC 15.247 and has single modular approval. Host integrator is responsible to ensure with relevant FCC rule parts.

• Responsible party (contact for FCC matters only): Nalloy LLC, 859 Willard Street, Suite 400, Quincy, Massachusetts 02169

• To meet RF exposure requirements, this radio module needs to be placed at least 20 cm away from the body of the user as well as other radio antennas.

• Integrators of radio module are responsible for performing FCC Part 15 Subpart B and spurious emissions verifications per KDB 996369.

• Integrators of the radio module are required to label the host device in a conspicuous location as Contains: FCC ID: 2AVOB-VG8HYF

• Integrators of radio module are required to perform necessary evaluation required by FCC when collocated with another transmitter.

• J2 antenna port connector is solely for test purposes to perform conducted measurements. The module is only intended for use with a PCB antenna. External antennas shall not be used.

• If the final host/module combination is intended for use as a portable device, the host manufacturer is responsible for separate approvals for the SAR requirements from FCC Part 2.1093 and RSS-102.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications to this product not authorized by Nalloy LLC could void the compliance certification of the device.

Host integrator shall include statements as stated in FCC 15.19, 15.21, and 15.105.

SI Labs rail test firmware can be used to configure the device to various test modes as required by FCC. https://www.silabs.com/documents/public/user- guides/ug409-railtest-usersguide.pdf. The module is not intended to transmit simultaneously with other radios.

Product Usage Instructions

1. Ensure that the radio module is placed at least 20 cm away from the body of the user as well as other radio antennas.
2. Use only PCB antenna with the module. Do not use any external antennas.
3. If you are integrating the radio module with other transmitters, ensure that necessary evaluation as required by FCC is performed.
4. If you are using the final host/module combination as a portable device, ensure that the host manufacturer has obtained separate approvals for the SAR requirements from FCC Part 2.1093 and RSS-102.
5. While operating the device, ensure that it does not cause harmful interference to other devices and accept any interference received, including interference that may cause undesired operation.
6. If you experience harmful interference to radio or television reception, try to correct the interference by one or more of the following measures:
   • Reorient or relocate the receiving antenna.
   • Increase the separation between the equipment and receiver.
   • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
   • Consult the dealer or an experienced radio/TV technician for help.
7. Do not make any changes or modifications to the product without authorization from Nalloy LLC as it could void the compliance certification of the device.
8. If you are a host integrator, ensure that you include statements as stated in FCC 15.19, 15.21, and 15.105.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>