Puig 20631N Triumph Trident Instruction Manual
- June 4, 2024
- Puig
Table of Contents
20631N Triumph Trident
Instruction Manual
www.puig.tv
www.puigusa.com
[email protected]
[email protected]
20631N Triumph Trident
TRIUMPH TRIDENT 660 ’21
REF 20631N
PROTECTOR MOTOR VINTAGE 2.0
https://qrgo.page.link/WJJST
INSTRUCTIONS TO ASSEMBLE
Remove the fasteners that subject the chassis to the engine. Mount the
protectors on each own side as the figure below shows. Tight the set, and
place the caps. All the screws replaced, should be tightened to the torque
specified in the OEM maintenance manual for your motorcycle. if no torque
specifications are provided in the OEM maintenance manual, may be used 54Nm
for all M10 screws. Medium-strength liquid thread-locker (i.e. “Loctite”)
should be used to secure all screws, bolts, and nuts. All screws, bolts, and
nuts should be checked after driving the first 50 km to ensure that all are
tightened to the proper torque.
TO ASSEMBLE THE CRASH PADS, IF YOU ARE NOT A TRAINED MECHANIC, PLEASE CONTACT
A SPECIALIST. MOTOPLASTIC, S.A. TAKES NO RESPONSIBILITY FOR DAMAGES CAUSED BY
IMPROPER INSTALLATION. THE USE OF CRASH PADS DOES NOT GUARANTEE A FULL
PROTECTION IN CASE OF AN ACCIDENT. MOTOPLASTIC-PUIG DECLINES ANY
RESPONSIBILITY IN CASE OF MOTORCYCLE DAMAGE. WENN SIE KEIN AUSGEBILDETER
MECHANIKER SIND, WENDEN SIE SICH BITTE AN IHRE FACHWERKSTATT.
| ID. | DESCRIPTION | QTY. | REF.: |
|---|---|---|---|
| 1 | M10/150×70 DIN912 screw | 1 | TORNIAD912-0347 |
| 2 | M10/150×100 DIN912 screw | 1 | TORNIAD912-0355 |
| 3 | M10 DIN6798/A washer | 2 | M2AM10DIN6798ZB |
| 4 | M10 washer | 6 | M2AM10DIN125AZB |
| 5 | Nylon Vintage Protector | 2 | PROTECVINTAGE– |
| 6 | Black aluminium spacer (40mm) | 1 | CASQU136-0-1436 |
| 7 | Black aluminium spacer (65mm) | 1 | CASQU140-0-1440 |
| 8 | Black right platen | 1 | PLATI398-0-0398 |
| 9 | Black left platen | 1 | PLATI170-0-0170 |
| 10 | M10/125×80 DIN912 screw | 1 | TORNIAD912-0338 |
| 11 | M10/125×100 DIN912 screw | 1 | TORNIAD912-0329 |
| 12 | M10/125×50 DIN912 screw | 1 | TORNIAD912-0335 |
| 13 | M10/125×120 DIN912 screw | 1 | TORNIAD912-452Z |
| 14 | Black aluminium spacer (32mm) | 1 | CASQU309-0-1609 |
| 15 | Black aluminium spacer (39mm) | 1 | CASQU468-0-1768 |
| 16 | Black aluminium spacer (10mm) | 1 | CASQU257-0-1557 |
| 17 | Black aluminium spacer (53mm) | 1 | CASQU194-0-1494 |
| 18 | DIN912 screw cap | 4 | TAPA–CHC10800E |
RIGHT SIDE
ASSEMBLY
LEFT SIDE
Documents / Resources
| Puig
20631N Triumph
Trident
[pdf] Instruction Manual
20631N Triumph Trident, 20631N, Triumph Trident, Trident
---|---