Chargers S5 Fast Wireless Charger User Manual

Chargers S5 Fast Wireless Charger

Thank you for purchasing and using this product!

Please read this operation instruction carefully before using this product.

Product Specification

Fast Wireless Charger

• Input:5V-2A/9Vm2A
• Output:5V=-1.0A/9V-1.2A
• Charging Efficiency: 70%

Applicable Devices

Compatible with all devices with Qi Standard For all other phones without Qi Standard, compatible if equipped with wireless receivers.

The LED light turns red during wireless charging to indicate a charging failure.

The following situation can cause failures, like charging slowly, stop charging, and over-temperature for charging position.

1. The adapter is not run up to standard (No PC USB output power supply)
2. The charging cable is not up to standard.
3. The phone case is too thick (within 2mm thickness phone case recommended). The built-in wireless charging receiver position is not coincided with wireless charger coil position.
4. There is metal/magnet on the back of cell phone or phone case.
5. Smartphone does not support wireless charging function.

Attention

1. Please keep the charger away from water or other liquid.
2. If you need to clean the charger, please make sure it is not connected to power supply.
3. Operating temperature: -20-45 C

Smartwatch charger placement method

1. Put the smartwatch charger into the crystal holder.
2. Put the cable in the slot.
3. Wrap the cable on the column.
4. Insert into the charging port.

Step to install an air vent

1. Follow the arrOws to install 3 parts.
2. Adjust the screw cap to the best active status.
3. Press the button of clip to fix, then adjust the angle and tighten the fixed nut.
4. Installation completed.

Step to install the suction cup

1. Follow the arrows to install 3 parts.
2. Adjust the screw cap to the best active status.
3. Adjust the angle of suction cup and empty air.
4. Tear off the red protective film and stick it on the dashboard
5. Paste the suction cup on the 3M auxiliary fixing plate, press it for 1 minute and let it stand for 1 hour.
6. Press the lever
7. Adjust the appropriate angle
8. Installation completed.

Step to use wireless charger

1. Input: Connect the wireless charger and car adapter with the charging cord.
   Please use a QC3.0/PD adapter so that the charging will enter the fast charging mode.

2. Place smartphone.
   Both sides of the clip open automatically after being powered, putting on a smartphone, the clip close automatically to tighten the smartphone.

3. Take off your smartphone.

4. LED indicator light shows the working status:

5. Red LED Light Is Always On Standby.

6. Blue LED Light: Charging normally.

7. Red LED Light Flashing: Charging abnormally.

FCC Requirement

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions,may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>