LANCOM IN-Q180+ Ceiling Antenna AirLancer Instruction Manual
- June 9, 2024
- LANCOM
Table of Contents
IN-Q180+ Ceiling Antenna AirLancer
Instruction Manual
IN-Q180+ Ceiling Antenna AirLancer
Mounting Instructions
LANCOM AirLancer
IN-Q180+
Preparation for wall- and ceiling mounting
Use the antenna as a drilling template to mark out the drill holes for wall-
or suspended ceiling mounting. The horizontal and vertical separation of the
adjacent holes is 104 mm. For ceiling mounting, if required, drill a hole into
the center of the ceiling board to feedthrough the connector cables.
Alternatively, you can use the integrated cable duct on the antenna backside
to lead the cables sideways.
Size of the drill holes
Using the markings as a guide, drill the holes and insert dowels for wall
mounting, if appropriate. Depending on the surface material the required size
of the holes may vary.
Mounting the antenna
1. Ceiling board mounting with screws and nuts
Included: 4 thread screws 30 mm, 4 washers, 4 nuts From the frontside, stick
the thread screws through the appropriate holes of the antenna housing and the
previously drilled holes of the ceiling board. Place the washers on the screws
from the backside of the ceiling board. Finally, use the nuts for fixing.
2. Ceiling mounting with screws and clips
Included: 4 clips, 4 thread screws 15 mm
Push the clips into the
appropriate slides at the backside of the antenna, so that the clips are
placed in line with the holes in the antenna housing. Stick the thread screws
through the holes in the antenna housing from the front side and loosely
connect the screws to the clips.
Now the antenna can be moved onto the existing or additionally mounted metal
ceiling t-bars. Finally, tighten the screws for proper fixing.
3. Wall mounting with screws & dowels
Included: 4 screws, 4 dowels
Place the antenna with its backside at the wall so
that the holes in the antenna housing are in line with the previously inserted
dowels. Stick the screws through the holes of the antenna housing into the
dowels and tighten the screws.
Important information
Responsible handling of high frequency
In order to comply with the protection requirements of EU Directive 2014/53
and EN 62479 with regard to the basic restrictions for the safety of persons
in electromagnetic fields and the „FCC Policy on Human Exposure to
Radiofrequency Electromagnetic Fields“, it is necessary to configure the
correct antenna gain in the WLAN router or WLAN access point.
Electrical and Electronic Equipment Act
Please do not dispose of electrical and electronic waste in household waste,
where it cannot be recycled. Make sure that your electrical and electronic
waste is disposed of in accordance with the currently valid guidelines of your
country.
Correct handling of antenna cables
Antenna cables are sensitive RF cables. When laying them, it is therefore
important to ensure that the cables are not kinked and are bent as little as
possible, as this can result in losses in terms of antenna performance.
Likewise, the antenna cables should not be wound into tight cable loops.
Antenna gain and termination of unused antenna ports on access points
Unused antenna connections on the access point must be terminated with an
enclosed rod antenna. For indoor access points, the terminating resistor
included with the AirLancer AN-RPSMA-NJ adapter can be used. In addition, the
antenna gain must be specified in the configuration of the access point.
| Technical details | IN-Q180+ |
|---|---|
| Frequency range | 2,400 – 2,500 MHz |
4,900 – 5,900 MHz
Antenna characteristics
Radiation characteristics| horizontally (2.4 GHz): 360°
vertically (2.4 GHz): 55°
horizontally (5 GHz): 220°
vertically (5 GHz): 40°
Recommended use| Room coverage
VSWR| 1.5:1 typ. / 2.5:1 max.
Gain| 2.4 GHz: 3 dBi max.
5 GHz: 5 dBi max.
Mechanical details
Size| 130 x 130 x 45 mm (length x width x height)
Weight| 208 g (antenna without mounting kit)
Temperature range| -20 °C to 65 °C
Color| White
Material| UV-resistant plastic
Mounting options| Ceiling- and wall mounting
Cables, connectors| 4 x 1 m RG178 cable with RPSMA plug
Item
Warranty| 2 years for AirLancer and accessories
Item number| 61262
Package content| Antenna, fastening material for ceiling- and wall mounting,
mounting instructions
Antenna patterns
LANCOM, LANCOM Systems, LCOS, LANcommunity and Hyper Integration are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. This document contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for technical errors and/or omissions. 111955 11/22
LANCOM Systems GmbH
Adenauerstr. 20/B2
52146 Wuerselen | Germany
info@lancom.de
www.lancom-systems.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>