REDRAGON DS-2885A Swain Gaming Mouse Instruction Manual
- June 13, 2024
- REDRAGON
Table of Contents
REDRAGON DS-2885A Swain Gaming Mouse
Dear user
Thank you for choosing our product. To protect your rights and for better
customer service, we ask that you note our warranty rules.
Within guaranty period, repair is guaranteed for failure due to electrical
circuit problems. Other damages, such as disassembly, hard impacts, submersion
into water, plugging into improper current or voltage, and damage caused by
natural disasters such as fire, flood, or earthquake are not included.
Consumable parts (such as foot pad) and spare parts replacement are not
Included In our warranty.
Button Instructions
- Left mouse button.
- Right mouse button.
- Scroll wheel (dicked as middle mouse button).
- Rapid fire button(Defaulted to three rapid clicks of the left mouse button)
- Side key, defaulted function: FORWARD key on the keyboard.
- Side key, defaulted function: BACKWARD key on the keyboard.
- DPI+ button (defaulted to speed up the cursor).
- DPI- button (defaulted to slow down the cursor).
- Light mode toggle key: The mouse switches between the 6 lighting modes for each click.
- User mode switch button
- Teflon foot pads
Lighting Instructions
- User mode indicator light: Located below the Scroll Wheel key.
- Red —— User mode
- Blue —- User mode
- Green — User mode
- Purple — User mode
- Yellow — User mode
- colors Indicator light
- Red—-Gear l (lop DPI)
- Blue —-Gear 2 (2000 DPI)
- Green–Gear 3 (4000 □Pl)
- Purple -Gear 4 (8000 DPI)
- Yellow –Gear 5 (26000 DPI)
- Lighting
Software Instructions
User can adjust the following settings through the software after downloading and installing it.
- Adjust the □Pl of the mouse at the user’s discretion.
- Adjust the polling rate of the mouse at the user’s discretion. (range: 125-250-500-lOOOHZJ.
- Macros: Record up to 59 actions and trigger with one key.
- Continuous keystroke function: Set the number of clicks and delay time.
- Lighting: Adjust mouse lighting options.
- Customize mouse buttons.
- Set 5 different user modes.
FAQ
- If the mouse is not responding, please check whether the mouse is plugged correctly in the corresponding computers USB port, or try another USB ports.
- If the mouse is moving slowly, jumping or with delay, please try another surface. Dark, dirty, un-flat, bright surfaces may affect the performance of mouse. Mouse pad strongly recommended.
FCC Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur particular
Installation. If this equipment does cause harmful Interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment Into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/T V technician for help This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions {l)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.