timberk T-SF1605RC Electric Floor Fan Instruction Manual
- June 9, 2024
- TIMBERK
Table of Contents
timberk T-SF1605RC Electric Floor Fan
DESCRIPTION
- Safety screw & nut
- Front grille
- Front grille clips
- Blade cap
- Blades
- Rear grille nut
- Rear grille
- Motor
- Control box
- Stand cover
- Extension pole
- Stand base
- L type base screw & washer
- Switch mode buttons
- Remote controller
IMPORTANT SAFEGUARDS
- Important safeguards. read carefully and keep for future reference.
- Incorrect operation and improper handling can lead to malfunction of the appliance and injuries to the user.
- Before connecting the appliance for the first time check that voltage indicated on the rating label corresponds to the mains voltage in your home.
- For home use only. Do not use for industrial purposes. Do not use the appliance for any other purposes than described in this instruction manual.
- Do not use outdoors or in damp area.
- The appliance is not intended for use for physically, sensory or mental disabled person (including children) or for person with lack of life experience or knowledge, if only they are under supervision or have been instructed about the use of the unit by responsible person.
- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Cleaning and user maintenance shall not be made by children unless they are older than 8 and supervised.
- Children must be under control in order not to be allowed to play with the appliance.
- Always unplug the appliance from the power supply before cleaning and when not in use.
- To prevent risk of electric shock and fire, do not immerse the appliance in water or any other liquids. If it has happened DO NOT TOUCH the appliance, unplug it immediately and check in a service center.
- Do not use the device in bathrooms and near water.
- Do not place the appliance near heat sources.
- Do not leave the appliance switched on when not in use.
- Do not use other attachments than those supplied.
- In case of power cord is damaged, its replacement should be done by the manufacture or service department or the other high-skill person to avoid any danger.
- Keep the cord away from sharp edges and hot surfaces.
- Do not pull, twist, or wrap the power cord around the appliance.
- Avoid contact with moving parts of the device. Do not put pencils or other objects through the protective grid of the fan.
- Do not operate without fan installed protective grid.
- Ensure that the fan is switched off from the supply mains before removing the guard.
- Do not attempt to repair, adjust or replace parts in the appliance. Repair the malfunctioning appliance in the nearest service center.
- If the product has been exposed to temperatures below 0ºC for some time it should be kept at room temperature for at least 2 hours before turning it on.
- The manufacturer reserves the right to introduce minor changes into the product design without prior notice, unless such changes influence significantly the product safety, performance, and functions.
- Manufacturing date is indicated on the unit and/or on packing as well as in accompanying documents in the following format XX.XXXX where first two figures XX is the month of production, and following four figures XXXX is the year of production.
ASSEMBLING INSTRUCTIONS
- Loosen the screw from the bottom of outer pipe
- Attach the extension tube in the hole of the round base and fix them with the L type base screw & washer.
- Attach the motor with switch compartment onto the inner pipe. ensure the switch compartment is pushed fully onto the inner pipe and secured with the set screw provided.
- Unscrew the plastic mounting nut from the front of the motor housing by rotating it anticlockwise.
- Position the rear grille against the front of the motor housing with the handle uppermost, ensuing that the locating pegs on the motor housing are engaged correctly in the holes of the rear grille.
- Tighten the Rear Grille Mounting Nut clockwise. DO NOT OVERTIGHTEN IT.
- Push the fan blade onto the motor shaft, locating the slot at the back of the blade on the drive pin that passes through the motor shaft.
- Tighten the blade cap by turning it anticlockwise.
- Position the front grille against the rear grille so that the holes in the rims that accept the small nut and bolt are in line. Insert the bolt through the holes and screw on the nut. Do not fully tighten at the stage.
- Push the grille retaining clips into position ensuring that they engage correctly on the rim of the grille.
- Fully tighten the small nut and bolt that passes through the rim of the grille.
OPERATION MANUAL
- Connect the appliance to a socket. All the indicator lights are on and the nixie tube is on for one second and then all go out.
- Switch on the appliance by pressing the ON/OFF button on the remote controller, or pressing POWER on control panel. Accompanied by two beeps, the fan starts to blow at low speed 1.
- To change speed, press button SPEED several times. Speed will change with each button stroke. The respective speed (1, 2, 3) will be shown by the LED.
- For oscillation, press the OSC button. The swing indicator light up and the fan starts oscillating. To stop oscillation, press button once again. When the fan is in stand-by mode, this button will not work.
- Your fan has a timer function. After having switched the unit on, press the TIMER button and the fan will operate for as long as you choose: Press the timer button several times and the setting will change with every button stroke. The fan can set the timer function from 1, 2, 3, 4, 5, 6, 7, 8, 9 hours, which will shown by the LED
- The air flow can be adjusted by tilting the entire motor unit upward or downward.
- To switch the fan off, press the ON/OFF button again.
- Always unplug the appliance when it is not used.
- CR2025 size battery is required to operate the remote control
MAINTENANCE
- Before cleaning unplug fan first.
- Do not use abrasive cleansers
- Clean front and rear grilles, blades, stand tube and stand base with soft moistened cloth and wipe dry.
STORAGE
- Keep the device in normal conditions in dry place.
- The symbol on the unit, packing materials and/or documentations means used electrical and electronic units should not be toss in the garbage with ordinary household garbage. These units should be pass to special receiving point.
- For additional information about actual system of the garbage collection address to the local authority.
- Valid utilization will help to save valuable resources and avoid negative work on the public health and environment which happens with incorrect using garbage.
The symbol on the unit, packing materials and/or documentations means the battery used in this product not be toss in the garbage with ordinary household garbage.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>