AUDIBAX Ovo Series 6 Black Pair of Passive Wall Speakers 6 Inches User Manual
- June 9, 2024
- AUDIBAX
Table of Contents
AUDIBAX Ovo Series 6 Black Pair of Passive Wall Speakers 6 Inches
EXAMPLE OF 70V/100V SYSTEM CONFIGURATION
NOTE:The total number of speakers multiplied by the tap value cannot exCeed the output power(in watts) of the 7ov 100V amplifier. The above examgle shows 5 total speakers. Using the 20W taps, you will need an amplifiler with at east (5)(20)=100W. A good rule of thumb is to select an ampifier with 20%% greater power; In this case, an amplifier that delivers about 125W.
UNDERPOWERING VS.OVERPOWERING
TECHNIAL SPECIFICATIONS
The OvO range is a series of wal speakers designed with a woofer from 103mm to 135mm and a 13mm tweeter. The OVO series is the perfect choice for the distribution of microphone calls and background music outside (1P65) both for restaurants or commercial stores. The mounting frame is made of high quality ABS. The grille is made of metal. The OVO is available in black/ white.
SAFETY PRECAUTION
- Keep this manual for future reference
- When cutting the mounting hole for the speaker, make sure there is sufficient clearance behind the panel (no obstructions like A/C channels, power lines etc).
- Do not use nails, adhesives or other unauthonized devices. Long-term use and vibrations can make it fall easily.
- Take care of your speaker wires, they should be free of damage. Damaged speaker wires might result in poor Sound quality and can damage amplifiers.
- Only use accessories specified by the manufacturer.
- Make sure the mounting panel can support the speakers weight.
- Use sufficient amount of speakers to avoid dead spots
- No mains power shll be connected to the loudspeakers, doing so will damage the speaker
- This apparatus should only be serviced by qualifed personnel. If not warranty might be void.
- Use cable of the right gauge, certainly for long runs
- Use cables with clear color indication and maintain polarity throughout the whole system.
- Avoid loud feedback from microphones, this can damage your speaker.
- Please check the units condition after unpacking. If the outside of the carton box has been damaged, inform your shipper immediately
WARRANTY
The warranty for hidden defects can only be considered if they appear within the 24-month warranty period. The warranty is not valid in case of misuse, wear., power surges, improper packaging or shipping. improper use or storage and failure to comply with Audibax recommendations. The product must be returned in the original packaging with proof of purchase made by an authorized distributor of Audibax.
CONNECTION
Use wire on the back of the speaker in the output tab of the amplifier(or
amplifier of radio).The speaker wire is on one side red and on the other one
black. Connect to the red side of the amplifler and speaker(+)tab. Connect one
end of the black side() in the other tab. Connect each speaker to make sure
that is not(+) inverted polarity. If the polarity of the speakers is reversed,
the sound will be unnatural and will play without bass.
- Fasten the bracket A to on the wall by 4 pcs Screws
- Fasten the bracket B to on the box
- Remove the waterproof cover Connect the speaker cable to the terminal(+”to+”,’to'”-“+)
- Screw bracket A and bracket B together
- Fasten the screws after horizontal rotation
When mounting the panel, check for cables or other obstructions behind the mounting wal. Ensure that the mounting structure is able to safely support the weight of the speaker
- Most speaker damage is caused by amplifiers with too little power(wattage).
- An overdriven amplifier lips the waveforms and sends distortion to the speakers.
- Clipping is usually audible; it may vary from a harsh sound to a fuzzy or unclear sound,
- If you hear this condition at loud volume levels, turn down the volume until the distortions no longer present.
- Damage caused by operating the speakers at distorted volume levels is not covered by the warranty.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>