anslut 018816 LED Head Lamp Instruction Manual

June 9, 2024
anslut

anslut 018816 LED Head Lamp Instruction Manual
anslut 018816 LED Head Lamp

SAFETY INSTRUCTIONS

Follow the safety instructions below to reduce the risk of personal injury.

  • Do not look at the light source or point it at people or animals – risk of blinding and permanent eye damage (retina).
  • Keep children under supervision to make sure they do not play with the product.
  • The product contains a lithium-polymer battery, which if handled incorrectly can be set on fire and result in personal injury.
  • Do not expose the product to heat, mechanical stress or anything else it is not intended for.

WARNING

IMPORTANT: The product emits optic radiation that can result in a risk of personal injury. Do not look at the light source when it is switched on. Risk of eye damage.

SYMBOLS

| Read the instructions.
---|---
| Approved in accordance with the relevant directives.
| Recycle discarded product in accordance with local regulations.
| Do not look into the light source.

TECHNICAL DATA

Battery Lithium-polymer battery, 800 mAh
LED CREE XPG
Switch Tactile
Beam focusing Focus ring
Front lens Lens
Size 70.5 x 51.4 x 42.5 mm
Charger 5V 1A
Charging time 3–4 h (depending on battery charge status)
Watertightness IPX3
Weight 120g

DESCRIPTION

FIG. 1
DESCRIPTION

  1. Power switch/output selector
  2. Function selector
  3. USB port for charging
  4. Battery indicator
  5. Focus ring

Supplied parts: head lamp, forehead and crown strap, charger cable.

Function modes

Luminous flux High Medium Low Save Max
320lm 142 lm 80lm 33 lm 400lm
Burn-time 3,5 h 7 h 13,5h 27 h 3h
Cast length Flood- light 37,5m 25 m 18,5m 912,5m
Spot- light 74,6m 68,7 m 47m 35,1m 97 m

The above parameters are only an approximation. The parameters may vary depending on environment, if the power is low or with each lamp.

Reduce the brightness to save power which will ensure that there is light provided when outdoors.

USE

OUTPUT SELECTOR
Save mode – Low – Medium – High.

  • Press for 0.5 seconds to switch on/off.

FUNCTION SELECTOR

  • Press for 0.5 seconds to switch on with Max, tap to show battery charge status (shown for 5 seconds).

CHARGING

  1. Put the USB charger cable in the charging port (mini-USB) on the back of the product.
  2. Connect the other end of the USB charger cable to a USB charger (sold separately), a computer USB port or the equivalent. The charge status is shown on the battery indicator.

NOTE:
The product cannot be used when charging is in progress.

NOTE:
The battery is only partially charged on delivery. The battery must be fully charged with the supplied USB charger cable before using for the first time.

WARNING!
Charge in a dry place.

BATTERY INDICATOR

FIG. 2
BATTERY INDICATOR 

  1. Press the button to activate the battery indicator. The battery charge status is shown for about 5 seconds when the indicator is activated.

Charging status : The blue indicator on the front of the luminaire shows the current state of charge of the battery.

FOCUSING

FIG. 3

FOCUSING

The dispersion and cast length of the beam can be adjusted with the focus ring.

  1. Turn the focus ring outwards to concentrate the beam for spot mode, turn inwards to disperse the beam for floodlight mode.

CLEANING AND MAINTENANCE

Clean the product with a dry, soft and lintless cloth. Do not use solvent, alcohol or other chemicals.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals