OSD AUDIO 452SC800D Subwoofer Amplifier Installation Guide
- June 9, 2024
- OSD AUDIO
Table of Contents
OSD AUDIO 452SC800D Subwoofer Amplifier
Preparation
Tools For Installation
- Pencil
- Drill
- Tape Measure
- Wire Cutter
- Phillips Screwdriver
- Utility Knife
- Safety Eye Wear
- Gloves
- Sandpaper
Speaker Wire Guide
- 18AWG minimum – for distances up to …………………. 10 ft
- 16AWG – from …………………………………..…… 10 to 50 ft
- 14AWG – from ……………………………………… 50 to 100 ft
Installation
Cut Out
NOTE:
This is the most important part of the entire installation.
If you are not certain whether any obstructions exist behind the desired mounting area, you should start by cutting a small hole in the center of your penciled mounting hole with a drywall saw.
Using the Cut-Out dimensions measure and trace a template on the wall in the desired location. Cut along the traced line using a drywall saw or rotary drill. Use a piece of sandpaper to sand down the cut-out edge for a smoother contour. (See Diagram 1.)
- Cut and prepare a hole to install the SL800D into a stud bay where it can be securely mounted to both wall studs.
- Once in place, the SL800D should be tested before securely mounting and moving onto step 3.
- The final step, install the magnetic grille system by simply laying it into place.
Specifications
- Dual In-Wall Subwoofer
- Power Handling: 300W
- Woofer: 8″ 8 Ohm
- Passive Radiator: 10″
- Sealed Tuned Enclosure
- Freq Response: 40Hz – 500Hz
- Overall Dimensions: H 22″ x W 17.5″ x D 4.3″
- Cut Out Dimensions: H 20″ x W 14.5″
- Mounting Depth: 3.9″
Warranty Information
All OSD AUDIO speaker products have a (10) year Limited Warranty against defects in materials and workmanship. Proof of purchase must accompany all warranty claims. During the warranty period, OSD AUDIO will replace any defective part and correct any defect in workmanship without charge for either parts or labor OSD AUDIO may replace returned speakers with a product of equal value and performance. In such cases, some modifications to the mounting may be necessary and are not OSD AUDIO’s responsibility.
For this warranty to apply, the unit must be installed and used according to its written instructions. If necessary, repairs must be performed by OSD AUDIO. The unit must be returned to OSD AUDIO at the owner’s expense and with prior written permission. Accidental damage and shipping damage are not considered defects, nor is damage resulting from abuse or from servicing performed by an agency or person not specifically authorized in writing by OSD Audio. OSD AUDIO sells products only through authorized dealers and distributors to ensure that customers obtain proper support and service. Any OSD AUDIO product purchased from an unauthorized dealer or another source, including retailers, mail-order dealers, and online sellers will not be honored or serviced under the existing OSD AUDIO warranty policy.
Any sale of a product by an unauthorized source or another manner not authorized by OSD AUDIO shall void the warranty on the applicable product. Damage to, or destruction of components due to the application of excessive power voids the warranty on those parts. In these cases, repairs will be made on the basis of the retail value of the parts and labor. To return for repairs, you must email customer service at RMA@audiogeargroup.com for a Returned Merchandise Authorization (RMA) number#, and then the unit must be shipped to OSD AUDIO at the owner’s expense, along with a note explaining the nature of service required. Be sure to pack the speaker(s) in a corrugated container with at least 3 inches of resilient material to protect the unit from damage in transit.
This Warranty Does Not Cover:
Damage caused by abuse, accident, misuse, negligence, or improper operation
(installation) Any products that have been altered or modified Any product
whose identifying number of decals, serial #, etc. has been altered, defaced,
or removed Normal wear and maintenance.
OSD Audio | Brea, CA | osdaudio.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>