All American AA Prestige A3 Printer for DTF User Manual
- June 9, 2024
- All American
Table of Contents
All American AA Prestige A3 Printer for DTF
Safety Instructions
When using your AA Prestige A3 Printer for DTF, basic precautions should always be followed, including the following:
- Read all instructions.
- Use the AA Prestige A3 Printer only for its intended use.
- To reduce the risk of electric shock, do not immerse the DTF printer in water or other liquids.
- Do not disassemble or attempt to repair the DTF printer. Take it to a qualified service person for examination and repair.
- This equipment is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of this equipment by a person responsible for their safety.
- Close supervision is necessary for any DTF printer being used by or near children. Do not leave equipment unattended while connected.
- The AA Prestige A3 Printer needs routine maintenance, please refer to the included manual.
Technical Parameters
| Model: | AA-PRESTIGE-A3-DTF |
|---|---|
| Printer Head: | Epson L1800 & 1390 |
| Printing Width: | 297 mm |
| Printing Resolution: | 2880 x 1440 DPI |
| Printing Speed: | A3 size (1440 dpi / 5-7 min) |
| Ink System: | 6 colors CISS |
| Software: | Arco RIP |
| Voltage: | 110 Volts |
| Machine Size: | 88 cm x 33 cm x 21.5 cm |
| Package Size: | 38 cm x 84 cm x 30 cm |
| Packing: | Wooden Crate + Pearl Foam |
| Net/Gross Weight: | 20 kg / 28 kg |
| Suitable Material: | Colton, polyser, PU |
| Warranty: | 1-year warranty on non-consumable parts and 6-month warranty on |
Printhead
Machine Views
Operations Instructions
- Connect the AA Prestige A3 Printer for DTF to power.
- Turn on the system.
- 2.1 Switch on the system.
- 2.2 Turn on the printer.
- 2.3 The power light will begin flashing as the auto inspection process begins.
- 2.4 The printer is ready once the power light stops flashing.
- Paper rolling test.
- 3.1 Locate one piece of black film.
- 3.2 Press paper / delete button.
- 3.3 Check if the paper can roll into the printer.
- 3.4 Check if the paper rolls out properly.
- Install ink waste bottle.
- 4.1 Remove waste ink bottle from the printer ink box.
- 4.2 Install waste ink bottle onto the back cover of the machine. Then, insert the waste ink tube into the bottle.
- Place the two waste ink plates under the printer.
- Fill the ink reservoirs.
- 6.1 Open the printer ink box cover.
- 6.2 Fill the ink reservoirs according to each color on the label.
- Inject the inks into the ink cartridges.
- 7.1 Take out the ink cartridges from the printer head.
- 7.2 Use the injector to inject into each cartridge from the ink reservoirs by pulling the injector plunger.
- Inject ink into the waste ink bottle.
- 8.1 Remove the ink waste tube from the ink waste bottle and withdraw waste ink with the injector by pulling the injector plunger.
- 8.2 re-insert the waste ink tube into the waste ink bottle.
- Software / Driver Installation.
Included in your shipment is 2 USB thumb drives. One thumb drive contains the key for the RIP software needed to operate the AA Prestige A3 Printer for DTF. The second thumb drive contains the downloadable folders.
Routine Maintenance
- Open the printer ink box cover.
- Remove the film.
- Switch on the printer.
- Open the RIP software and begin the head cleaning process (press F12).
- Locate one piece of blank film.
- Open RIP software and initiate the nozzle check process (press F11).
- Perform test print. If test shows solid lines, your printer is ready for use.
- Perform test print. If the test print shows broken lines, go back to step 1 to perform routine maintenance again.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>