All American BNDL-AA-24IN-R-SHAKER-A AA 24 Inch DTF Powder Recirculating Applicator and Dryer Combo Instruction Manual

AA 24 Inch DTF Powder Recirculating
Applicator and Dryer Combo v3
Manual

BNDL-AA-24IN-R-SHAKER-A AA 24 Inch DTF Powder Recirculating Applicator

and Dryer Combo

Thank you very much for purchasing this product! Please read this manual carefully before use. Please keep this book in a safe place for future reference.

Contents

Dear user,
Thank you for using our products!
In order for you to use this product correctly, please read this manual carefully before installing and using the product. Please make sure to keep this manual for future reference.
While using our powder applicator and dryer products, it is important that you carry out regular cleaning and maintenance. If the product is not properly maintained, the chances of failure will increase and its service life will be greatly reduced.
Please contact your local service center or us directly for yearly paid inspections and maintenance services with one of our specialists.

Safety Warning

Caution

This section describes the contents and importance of safety matters to prevent personal injury or property damage to users or others. Please readthetextwitha a full understanding of the following contents (symbols and icons). and be sure to observe the described safety matters.
Prohibited Use, Materials, and Operation

• Do not pull the power cord. always hold the plug tightly and pull it out directly from the socket. To ensure safe use. please do not damage the power cord at any time, when the power cord is broken or the plug is worn, do not use it. If the power cord is worn or damaged. it must be replaced at the maintenance point designated by the manufacturer.
• Private disassembly. transformation and prohibition of damage to the equipment are strictly prohibited. and repair of equipment must be carried out by professional personnel. If the power cord is damaged. it must be replaced by the manufacturer, its maintenance department, and related professionals in order to avoid danger.

Mandatory Warnings & Requirements

• Be sure to ensure that the grounding pole of the outlet has a reliable ground wire.
• The AC220V AC power supply used by this shaking machine will cause the service life of the shaking machine to be reduced if the voltage exceeds the rated voltage range by 10%.
• Please do not put flammable. explosive. volatile and highly corrosive items near the shaking machine to avoid damage to the product or fire and other accidents. Please do not place or use combustible items near the shaking powder machine to avoid fire.

Use Caution in Case of Injury

• For safety. it is recommended not to place debris on top of the powder shaker.
• Avoid hand contact with the surface of the equipment for a long time to prevent hand burns.
• Unplug the power when the power is off or when cleaning.

Product description

Part name

Tips

 All illustrations in this manual are for explanatory purposes only. In case of inconsistency between its appearance, function and the actual product, please refer to the actual product.

Accessory list

Release cloth steel tube| Square magnet| Aluminum tube stopper| H5 Single Power Receiver| Instruction manual
---|---|---|---|---
2pcs| 2pcs| 4pcs| 1pcs| 1pcs

Operation panel

Instructions for use

Instructions for USC(Steps 1-6 are instructions for installing and using the printer, and the instruction process for shaking the powder machine starts at 7)

1. Open the box tool, use the tool to open the box. and check the random accessories after opening the box.
2. Installation of the foot. the accessories required for the foot (bottom beam, paper take-up and payoff. waste ink bucket. take-up and payoff cloth holder X 2. foot X 2, and base plate X 2 ). the installation of the machine (pay attention to the direction of installation of the bracket left and right). respectively. the bottom of the foot and the bottom of the foot base plate screw holes with screws to lock, install the foot bottom beam. install the take-up and payoff cloth holder, and install the take-up and payoff cloth steel pipe. the installation of the waste ink bucket (pay attention to the location of the installation). the installation of the foot is complete (pay attention to the installation direction of the bracket). fix the machine body on the foot. loosen the four screws fixed on the packaging of the machine body. lock the screw holes above the foot and the bottom of the machine body with screws.
3. Installation of the ink drum
4. Check the trolley movement. drying fan, heating, stepping, and ink stack working action. When the power is not on, manually lower the ink stack to the lowest level and manually move the carriage to check where there is interference. Power on the self-test. check the carriage movement and ink stack working action. check the drying fan. front. middle and back heating and stepping. RIP a picture to test the movement and whether it can print the effective width properly.
5. Installation of printhead and ink injection, check the ink stack and printhead installation hole position is appropriate. printhead installation as well as printhead line inserted in the printhead plate. ink injection. first through the syringe ink into the ink capsule, inserted in the printhead by color sequence.
6. Software cleaning and printing test. through the software cleaning printheads. print test strips. print calibration test.
7. Machine installation, printing, shaking powder, and drying, check the receiving spare parts. fix the receiving device with screws. add hot melt powder within 2 kg (standard) on the shaking powder machine. the receiving device is assembled. the receiving device is assembled. Print film loading, adjust the print film and lock the pressure wheel. fix both sides of the positioning piece. adjust the articulation table of the shaking powder machine. Start printing. then manually transition the print film. Power on the shaker, turn on the heating, drying, and manual stepping, and turn on the upper spiral. lower spiral and vertical spiral buttons, and make sure the powder return is normal. adjust the drying temperature to about 150’C. and adjust the articulating table temperature to about 60’C. Turn on the power of the smoke evacuator.
8. In printing. shake the powder machine on the powder, and fix the printing film with a magnet. turn on the powder spreading manual and adjust the size of the powder spreading vibration, spreading powder, turn off the powder spreading manual, turn on the powder spreading automatic, turn off the stepping manual, and turn on the stepping automatic. Use a section of unused print film, from the exit end of the shaking powder machine (to prevent shaking powder, just on the print film backward slippage problem), open the wind pump switch, manually move the print film to the suction port suction, open the shaking powder button, check the beginning of the print film is not evenly sprinkled, not manually sprinkled with some powder.
9. On the paper cylinder, adjust the winder, after printing, manually move a small section of the print film, carefully cut off the print film, with the help of a small magnet, the end of the print film fixed on the machine, you can move the small magnet, so that the back of the print film along the edge slowly into, close the step automatic, open the step manual, after the manual step, the guide belt will automatically move the print film from the suction magnet. Close the powder spreading automatic, close the shaking powder, drying process, printing and drying is completed, finishing the printed film.

Cleaning and maintenance

Caution
This section describes the contents and importance of safety matters to prevent personal injury or property damage to the user or others. Please read the text with a full understanding of the following contents (symbols and icons), and be sure to observe the described safety matters.
Caution
When cleaning the powder shaker turn off the power first.
Cleaning

• The dust on the body and ground of the powder shaker should be cleaned on time to improve the heat dissipation effect. with to help save energy.
• shaking powder machine should be cleaned frequently when cleaning. please use a soft towel or sponge. dipped in water or Non-corrosive neutral detergent cleaning. and finally, wipe clean with water. dry rag dry.

Warning
Do not use hard brush wire balls. wire brushes. abrasives (such as toothpaste), or organic solvents (suchas alcohol. acetone. banana water, etc.) boiling water, and acid, and alkaline items to clean the Shake the powder machine. caution
Do not rinse with water when cleaning to avoid affecting the electrical insulation performance. When cleaning electrical parts, please Use a dry wipe.

• Unplug the power supply when not in use for a long time to avoid electric shock or fire due to the aging of the power cord.

Service Guide

Non—Troubleshooting
caution
Note: If there is still a problem with the shaking powder machine after the non-fault check, please cut off the power and contact the after-sales service center. Before asking someone to check or repair, please check the following points.

Press the switch machine does not
respond| Maybe the main control switch is not
turned on| Check the general switch.
re-energize
Sprinkle powder switch, the machine
is not normal sprinkle powder| Is the intensity of the dusting
switch adjusted to the right
position| Adjust the dusting timer
Shaking powder machine does not
heat up| The temperature sensing probe is loose| Open the shell, check the terminals
Oil dripping from the machine| Oil accumulation inside the tunnel| Open the tunnel cover and clean up
the oil accumulation
Automatic does not go stepping| Photoelectric induction is not
sensitive| Adjust the photoelectric induction
The guide belt does not move.
electric motor| Guide belt slipping| Use a hexagonal wrench to tighten the
mesh belt
Return powder is not normal| check whether the vertical spiral
and the lower spiral is open
©Whether there is powder in the
Powder inlet| Open the switch to add powder

Product parameters

Note The parameters in this table are for reference only. please refer to the nameplate when the contents in this table and the machine nameplate conflict.

Shaking powder machine parameters

1Madel| T200
Type| 2 in 1 large DTF printing solution
Product name| Not stamping shaking powder machine
Rated voltage and current| Rated voltage AC220V.50/6011z AC1I0V.50/60Hz Rated current 10A/20A
Rated power| About 7500W
Place of origin| Zhongshan. Guangdong. China
Brand Name| Titan jet
Automatic grade| Automatic S
Vain Selling Points| Automatic powder return patent
Matching roll| PET film
Weight| Gross weight: 260KG Net weight: 180KG
Printing size| 600mmiXN
Applicable industries| Garment stores. printing stores. garment factories. traders and processing plants.
etc.
Protection against electric
shock type| ltyPo
Warranty range| 1 year
Working environment temperature| 18t -28t
Working environment humidity| 40%-80%
Main components| Main control board. motor, headboard. intelligent thermostat and display
Dimensions (LIMN)| Machine size: 2520mmX1120mmiX1150am Packing size: 22401m1X1180neX13801m1
Usage| Paper printer. label printer. card printer. tube printer ticket printer. leather cloth printer
Plan composition| Counter roll printer and powder shaker
After-sales service|  Online support. free spare parts. on-site installation. commissioning end training. service on-site maintenance and repair service. video technical support
---|---

Service guidelines
Caution

1. This warranty card is kept by the customer, together with the purchase invoice as the product warranty certificate.

2. the product since the date of purchase, in the “three packages” within the period without unauthorized disassembly and repair and indeed due to the quality of product manufacturing caused by the failure of the customer service department or special maintenance department identification.
   with the warranty card and purchase invoices, with reference to the national economic and trade (some goods repair replacement return responsibility regulations) (“new three packages “regulations) for the user for warranty.

3. users due to transportation, use, maintenance, improper storage, or non—assumption of the “three packages” repairer disassembly caused by damage; no warranty card and a valid invoice; warranty card model and repair product model does not match or altered: damage caused by force majeure. is not in the warranty.

Warranty period definition
The whole machine in the product from the date of purchase, in the warranty period, and the implementation of free repair.

Free repair conditions

1.  Where the purchase of equipment series products has been in our company for warranty registration procedures for users.
2. Hold a valid warranty certificate (warranty card), and the name, model, and bar code of the product must be consistent with the warranty card; if you can not provide a valid warranty card, the warranty will be extended by 6 months on the basis of the warranty period calculated from the date of delivery of the machine bar code.
3. Must be within the warranty period.
4. Failure is not caused by human factors. Product warranty period

headboard, intelligent thermostat, and display

Warranty card

Relevant information (user to fill in)

User
Name| | Contact Number|
Correspo dense address| | Purchase Store|
Date of purchase| | Invoice number|
Maintenance Record

Repair date| | Repair Unit|
Fault content and
Treatment|
Repair point| | Contact number|
Maintenance record

Repair date| | Maintenance
nice unit|
Fault content and
Treatment|
Repair point| | Contact number|
Maintenance record

Repair date| | Maintenance
nice unit|
Fault content and
Treatment|
Repair point| | Contact number|

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>