alphacool ST30 Core Wind Water Cooling Set Instruction Manual

alpha cool ST30 Core Wind Water Cooling Set

ACCESSORIES

COMPONENT STRUCTURE

DC-LT 2 PUMP

• Mount the DC-LT 2 pump in your Eisstation. The exact installation is described in the manual enclosed with the Eisstation.

RADIATOR PREPARATION

ALPHACOOL CORE WIND 240MM ST30 WATER COOLING SET

• NexXxoS ST30 Full Copper 240mm Radiator

ALPHACOOL CORE WIND 360MM ST30 WATER COOLING SET

• NexXxoS ST30 Full Copper 360mm Radiator
• Close all unused ports of the radiator with the screw plugs.

XP³ ASSEMBLY

• Do not use tools, only tighten up hand-tight!
• Mount the XP³ cooler on your mainboard. The exact installation can be found in the instructions enclosed with the XP³ cooler.

FAN – RADIATOR ASSEMBLY

ALPHACOOL CORE WIND 240MM ST30 WATER COOLING SET

ALPHACOOL CORE WIND 360MM ST30 WATER COOLING SET

Usually, the radiator is mounted on the top or in the front. The airflow in an ATX enclosure normally comes in from the front and out the top and back. The exact installation instructions are enclosed with the radiator.

CONNECTING THE FANS

• Fans
• Connect the 4-pin PWM adapter to the mainboard.

CONNECTING THE LEDS

Connect the 3-pin adapters to the Eiscontrol as shown.

INSTALLATION THE HOSE

• Do not use tools, only tighten up hand-tight

1. Roughly cut your hose to size.
2. Screw the fitting into the component and unscrew the union nut.
3. Make sure that the union nut is on the hose.
4. Now push the tubing over the fitting.
5. Finally, tighten the union nut over the fitting to complete the installation.

WATER FLOW DIRECTION

ALPHACOOL CORE WIND 240MM ST30 WATER COOLING SET

• Example

Note

• When integrating a GPU cooler, at least two additional connections are required and can be purchased separately under item no.: 17230 or 17228.

QUICK RELEASE

The quick-release fastener is not necessarily required.
Connect the hose:

1. screw the fitting into the quick-release fastener.
2. Make sure that the union nut is on the hose.
3. put your hose onto the quick-release fastener.
4. then screw the union nut back on the fastener.

Open the quick-release lock:

1. you can open or close the quick-release coupling with the lock, yellow arrow.
2. The quick-release fastener enables an uncomplicated extension of the system.
3. you can optionally purchase further quickrelease fasteners: item no.: 17396.

ALPHACOOL CORE WIND 360MM ST30 WATER COOLING SET

• Example

Note

• When integrating a GPU cooler, at least two additional connections are required and can be purchased separately under item no.: 17230 or 17228.
• The two examples show the water flow direction and the temperatures (dark blue “cold” > red “warm”). You can freely select the tubing.

COOLANT

Connect the pump to your power supply. Set your power supply unit to OFF at the switch and plug the ATX jumper plug into the 24-pin power cable of the power supply unit. Now fill the reservoir. When you set the power supply unit to ON at the toggle switch, the pump will start and the water will be pumped into the cooling circuit. Meanwhile, keep filling the reservoir with liquid so that the pump cannot run dry. When the system is filled and no more air collects in the reservoir, close the reservoir and carefully tilt the system back and forth in all directions while the pump continues to run. Now check the reservoir again. If air has collected in it again, add some more liquid.

LEAK TEST

Before you finally put your system into operation, we recommend that you carry out a 24-hour leak test:

1. Make sure that your power supply is switched off.
2. Connect the supplied ATX jumper plug to the power plug of your power supply.
3. Connect only the pump to the power supply.
4. Before starting the power supply, ensure the reservoir is filled with coolant.
5. Do not let the pump run dry to avoid damaging it.
6. If no water has leaked out after 24 hours, remove the ATX jumper and connect all other components properly.
7. Your cooling system is now ready for use

CHANGING THE COOLANT

Switch off your PC. Have a bowl ready to collect the coolant. Undo the quick- release fastener and remove the hose connector from the direction of the pump. Remove the second fitting and pull off the hose. Remove the remaining liquid by tilting the housing. Re-attach all the hoses again, then fill the loop with new coolant.

• Alphacool International GmbH
• Marienberger Str. 1
• D-38122 Braunschweig
• Germany
• Support: +49 (0) 531 28874 – 0
• Fax: +49 (0) 531 28874 – 22
• E-Mail:info@alphacool.com
• https://www.alphacool.com

Documents / Resources

| alphacool ST30 Core Wind Water Cooling Set [pdf] Instruction Manual
ST30 Core Wind Water Cooling Set, ST30, Core Wind Water Cooling Set, Wind Water Cooling Set, Water Cooling Set, Cooling Set
---|---

References

• Alphacool - Your water cooling specialist

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>