OSD AUDIO 452FZA850V Forza 850T Outdoor 70V 8ohm Omni Speaker Installation Guide
- June 4, 2024
- OSD AUDIO
Table of Contents
FORZA850T
OUTDOOR ?0V/8O
OMNI SPEAKER
INSTALLATION GUIDE
452FZA850V Forza 850T Outdoor 70V 8ohm Omni Speaker
Amplifier and Receiver Consideration
The Omni speakers should be powered by an amplifier or receiver that provides
a minimum of 10 watts per channel.
Optional Accessories – Outdoor Volume Control (OSD-OVC300)
Tools needed for installation
– Spade or trench tool
– Direct burial-rated speaker cable
16AWG ………………………………………………………100 ft
14AWG ………………………………………………………100 – 150 ft
12AWG ………………………………………………………150 – 200 ft
Specifications
Design:| All weather high fidelity in ground 360 the sound speaker is made
with reinforced resin for
---|---
Tweeter:| 1″ mylar Whizzer cone
Woofer:| 8″ with a 360 horizontal dispersion pattern
Frequency Response:| 42 Hz- 20 kHz
Power Handling:| 200W
70V Tap:| 20W, 40W, 60W
Impedance:| 8Ohm
Sensitivity:| 88 dB
Dimensions: (L x W x H)| 14″x14″x17″
Gross Shipping Weight:| 13.5 lbs
Unit of Measure:| 1 Piece
Warranty:| 1 Year
Warranty Information
All OSD Audio speaker products have (1) year Limited Warranty against defects
in materials and workmanship. Proof of purchase must accompany all claims.
During the warranty period, OSD will replace any defective part and correct
any defect in workmanship without charge for either parts or labor.
OSD Audio may replace returned speakers with a product of equal value and
performance. In such cases, some modifications to the mounting may be
necessary and are, not OSD’s responsibility.
For this warranty to apply, the unit must be installed and used according to
its written instructions. If necessary, repairs must be performed by OSD. The
unit must be returned to OSD at the owner’s expense and with prior written
permission. Accidental damage and shipping damage are not considered defects,
nor is damage resulting from abuse or from servicing performed by an agency or
person not specifically authorized in writing by OSD.
OSD Audio sells products only through authorized dealers and distributors to
ensure that customers obtain proper support and service. Any OSD product
purchased from an unau authorized dealer or another source, including
retailers, mail-over dealers, and online sellers will not be honored or
serviced under the existing OSD warranty policy. Any sale of a product by an
unauthorized source or in another manner not authorized by OSD shall void the
warranty on the applicable product.
Damage to or destruction of components due to the application of excessive
power voids the warranty on those parts. In these cases, repairs will be made
on the basis of the retail value of the parts and labor. To return for
repairs, you must email customer service at RMA@os daudio.com for a Returned
Merchandise Authorization (RMA) number# then the unit must be shipped to OSD
at the owner’s expense, along with a note explaining the nature of service
required. Be sure to pack the speaker(s) in a corrugated container with at
least 3 inches of resilient material to protect the unit from damage in
transit.
This Warranty Does Not Cover: Damage caused by abuse, accident, misuse,
negligence, or improper operation (installation)
- Any products that have been altered or modified
- Any product whose identifying number of decal, serial #, etc. has been altered, defaced, or removed
- Normal wear and maintenance.
Step 1
Evaluate the location of the speakers. Project the length of speaker wire you
will run. Note: when purchasing additional direct burial speaker wire, make
sure the wire gauge is consistent. Omni speakers reproduce sound in a full 360
degree and a few speakers will cover a large area with sound if properly
placed and spread out.
Step 2
Once you have decided on the locations for your in-ground speakers, dig a
trench about 5″ leading from the speakers to the input source for the speaker
cables. For the FORZA850T Omni speaker, dig a trench hole approximately 16″ in
diameter and 1 O” deep for the speaker enclosure.
Step 3
Place the Omni speaker in the hole you have dug. Run the direct burial wire
through the trench to the loca notion of the amplifier or receiver. Please
note: When connecting the additional wire be sure to use water-tight wire
connectors.
Step 4
Use the Tap switch located on the speaker to select the appropriate setting
best suited for your application.
Step 5
Connect the wires from the Omni speakers to the amplifier or receiver. Please
make sure the polarity on the cables and the speakers are in sync. Optional:
Using an outdoor volume control makes it convenient for you to adjust the
volume outside..
Step 6
Turn on your amplifier or receiver to test the speakers. If the speakers sound
fine, refill the wiring trench and cover the submerged part of the speaker.
OSD Audio I Brea, CA Iosdaudio.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>