AUDIBAX Control 8 192 Channel DMX Controller User Manual
- June 9, 2024
- AUDIBAX
Table of Contents
AUDIBAX Control 8 192 Channel DMX Controller
Please read the manual before using the product.
PROGRAMMING
Power on the unit, it will be in MANUAL mode. Press PROGRAM 2 seconds. The corresponding LED will flash. SCENE and CHASE will be ready to be programmed. To return to play mode, press PROGRAM once more. The led will then turn off.
AUTO
- In playback mode (RUN) press Auto/Del, and the led will turn on, indicating that the AUTO/RUN mode is activated.
- Press this key to program SCENEs or CHASEs when in PROGRAM mode.
TAP SYNC
- In AUTO RUN mode, the playback speed will be recorded by the last two button presses.
- In program mode, select the screen between STEP and BANK.
BLACKOUT
Press this button to disable all data output (no other functions) – Press
it again to exit this mode and send DMX data again.
DMX OUT
- DMX512 data output
DC INPUT
- DC9V～12V ,300
PROGRAMMING SCENES
- Press PROGRAM 3 seconds. The corresponding led will flash, indicating that the unit is in PROGRAM mode.
- Press the SCANNER button (or buttons, if you want to program several devices at the same time). Adjust the faders to your liking.
Main Features
- 192 DMX Channels.
- 30 Banks, each with 8 programmable scenes.
- 8 Faders for real-time adjustment.
- AUTO mode is controlled by TAP SYNC and SPEED.
- LED display with 4 digits. The first digit shows CHASE and the second SCENE. The third and fourth digit shows the banks. The second, third, and fourth digits show steps from 0 to 255 or time.
- Manual Blackout.
- Fade Time Control (FADE TIME)
Technical specifications
- Power: DC+9-12V
- Output: AC230V～50Hz (AC120V～60Hz)300Ma ,DC9V300Ma.
- Measurements
- Weight
INSTRUCTIONS FOR USE
- There are 192 DMX channels available for each scene.
- 8 scenes can be programmed per bank. When a scene is activated, it will play along with the others in that bank in a loop.
- Select the bank by pressing the UP and DOWN buttons. There are 30 banks available, only one is selectable at a time.
- Scenes can run automatically, and their duration depends on the tempo tapped by TAP SYNC., Scenes are executed under music or NOTE triggering, also press a scene button by hand to run scenes.
- 6 selectable chases are available, each with 240 scenes.
SCENES
While Control 8 is in PROGRAM mode, press PROGRAM for 2 seconds and it will
enter MANUAL mode. If there are no scenes programmed in a bank, they cannot be
played. Only those that have been previously programmed will be executed.
MANUAL OPERATION
Select a bank, and press SCENE to play a scene. If you press a SCANNER button, it will be registered to record in another SCANNER.
AUTORUN
Press AUTO/DEL and the corresponding led will light up. Press TAP
SYNC/DISPLAY, and after waiting for a moment, press it again. This interval is
assigned to the speed of the Auto Run mode, with a limit of 10 minutes. If
there are more than two clicks, only the last two will be taken as a
reference.
Scene buttons
Press a scene button to activate or store it, and the second digit of the
display will show the scene between 1 and 8.
Page Selection
Press the PAGE SELECTOR button to select between channels 1-8 and 9-16 of each
SCANNER.
Fader SPEED
Move the fader to adjust the speed of the CHASE.
Fader TIME SLIDER
Move this fader to adjust the fade time.
BANK ( UP or DOWN ) buttons
Press UP or DOWN to increase or decrease the bank number, which is shown in
the third and fourth characters of the display (01 to 30).
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>