ACCORD LIGHTING 1323 Ceiling Light Instruction Manual
- June 9, 2024
- ACCORD LIGHTING
Table of Contents
ACCORD LIGHTING 1323 Ceiling Light Instruction Manual
ASSEMBLY INSTRUCTIONS
WARNING!
Be sure electrical power is OFF before and during installation or maintenance.
The luminary must be installed by a qualified electrician, in accordance with
all applicable local codes.
Ensure that the rated luminaire voltage requirements are compatible with the
available
mains supply in which it will be installed.
All LEDS are included in your lamp. Never touch the LED surface with your bear
hands as this may reduce the life of your LED. Do not alter, relocate or
remove any electrical component.
Line: Oval
Family: Pendant
Description: Oval Accord Pendant 1323
Material: Natural Wood Veneer MDF and Acrylic
Weight:
INSTALLING THE FIXTURE ON CEILING
Turn OFF the power before start the installation.
-
Align and mark on ceiling the position of the holes where anchors will be installed. Drill using an 8mm drill bit and install the supplied plastic plugs.
-
Screw the anchors to the plastic plugs.
-
Pass the support steel cables through the holes on anchors making sure the ball-end of the cables are in the inner part. Then, screw these assemblies into each anchor fixed on ceiling.
-
Insert the other end of each cable into the adjustable anchors mounted on top of the luminaire until they are tight.
-
Reserve extra cables by wrapping them inside of the luminaire. It is not necessary to cut the excess off, but ensure that the cables cannot touch any of the electrical connections.
ADJUSTING THE FIXTURE HEIGHT
Choose the height (H) you want the luminaire to hang below the ceiling by pushing on the anchor to release tension. While pressing the tip, move the cable until it reaches the desired length. Release the tip and the cable will be locked again. Final adjustments can be made after the fixture is mounted. Now you are ready to make the electrical connection.
ATTENTION !
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY CAUSE ACCIDENTS AND LOSS OF
PRODUCT WARRANTY. Its recommended to read these instructions completely and
carefully before proceeding.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ACCORD Lighting guarantees coverage against manufacturing defects including
electrical components and finishes, for a period of three years, under normal
use, from the date of purchase. For warranty service, please contact your
local dealer for further instructions. Proof of date of purchase will be
required for validation of warranty service.
The responsibility of the manufacturer regarding the product warranty is
related to the correct observation of the instructions contained in this
manual. The manufacturer is not responsible for any damage to the product
caused by accidents, alterations of any kind, improper usage or improper
installation. See the website for additional warranty details.
ACCORD
Lighting reserves the right to change the dimensions and specifications
contained in this manual without prior notice, in accordance with its policy
of continuous product improvement. Please, contact the manufacturer if
additional information is necessary. The illustrations in this manual are for
guidance only and may vary in scale, dimensions and model details.
ASSEMBLY INSTRUCTIONS
WARNING!
Be sure electrical power is OFF before and during installation or
maintenance. The luminaire must be installed by a qualified electrician, in
accordance with all applicable local codes.
Ensure that the rated luminaire voltage requirements are compatible with the
available mains supply in which it will be installed.
All LEDS are included in your lamp. Never touch the LED surface with your bear
hands as this may reduce the life of your LED. Do not alter, relocate or
remove any electrical component.
- Color Temperature: 2700K, 3000K, 3b500K or 4000K
- CRI: 90
- Luminous Flux: 1485lm
- Total Power: 27W
- Input Voltage:110V or 277V
- Input Frequency:60 Hz
- Isolation: Class II
- Material: Natural Wood Veneer MDF and Acrylic
- Weight: Height Adjustment
- Limit: 160cm/63in
MAKING ELECTRICAL CONNECTIONS **
**
-
Pass the power supply cable through the strain relief cone, threaded tube niple, canopies and crossbar.
-
Connect the electrical supply wires to the junction box in accordance to all applicable local codes, as shown in the diagram
MOUNTING ON THE FIXTURE -
Attach the crossbar to the junction box using the supplied screws.
-
Attach the base the junction box using the supplied screws.
-
Bring the canopy to the ceiling and secure it by screwing the side of the canopy at it’s base.
Turn ON electrical power.
Your luminaire is now ready for use.
DIMMER COMPATIBILITY
The LED driver included with this fixture is designed to operate with most standard dimmers. All power ratings and installation instructions from dimmer manufacturers’ instruction sheets must be followed.
ATTENTION!
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY CAUSE ACCIDENTS AND LOSS OF
PRODUCT WARRANTY. Its recommended to read these instructions completely and
carefully before proceeding
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ACCORD Lighting guarantees coverage against manufacturing defects including
electrical components and finishes, for a period of three years, under normal
use, from the date of purchase. For warranty service, please contact your
local dealer for further instructions. Proof of date of purchase will be
required for validation of warranty service.
The responsibility of the manufacturer regarding the product warranty is
related to the
correct observation of the instructions contained in this manual. The
manufacturer is not responsible for any damage to the product caused by
accidents, alterations of any kind, improper usage or improper installation.
See the website for additional warranty details
ACCORD Lighting reserves the right to change the dimensions and specifications contained in this manual without prior notice, in accordance with its policy of continuous product improvement. Please, contact the manufacturer if additional information is necessary. The illustrations in this manual are for guidance only and may vary in scale, dimensions and model details.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>