ROVUS VC3953-GS Nano Hand Vac User Manual

: June 8, 2024
: ROVUS

Table of Contents

VC3953-GS Nano Hand Vac
PARTS
BEFORE USE
Charging
USAGE
CLEANING AND MAINTENANCE
TROUBLESHOOTING
TECHNICAL DATA
Explanation of markings
Documents / Resources

NANO HAND VAC
MODEL NO.: VC3953-GS
USER MANUAL

VC3953-GS Nano Hand Vac

PICTURES

Please read this manual thoroughly before using and save it for future reference.
WARNINGS

This device can be used by children aged from 8 years and above as well as by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the device in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance should not be done by children unless they are older than 8 and supervised.
Keep the device and its cord out of reach of children less than 8 years old.
This product is intended for household and dry use only.
If the device is not working as it should, has received a sharp blow, has been dropped, damaged, left outdoors or dropped into water, do not use it.
Do not attempt any modification or repair by yourself and ensure that any repair is conducted only by appropriately qualified technician.
Never run the device unless it is fully assembled.
Do not place the power cable near a heated surface.
Plug in power supply that corresponds to the rated one on charger only. In case of misusage power supply or device failure may occur.
Never use the power cable to pick up, carry, drag, pull, or lift the charger. Do not pull the power cable against or around sharp corners and edges.
If the power cable is damaged, it must be replaced immediately by authorized or similar qualified person in order to avoid a hazard.
Do not store device with batteries in very warm places as this could result in reduced battery performance and/or battery leakage. Battery acid and leakage can cause personal injury and/or damage to the product and/or surrounding property. If battery leakage occurs, thoroughly wash any affected skin, making sure to keep battery acid away from eyes, ears, nose and mouth. Immediately wash any clothing or other surface that came into contact with leaked battery acid.
A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack; never use the charger with another device or attempt to charge this product with another charger.
Do not expose to high temperatures >50 °C. The battery may degrade at high temperatures.
Charge battery in conditions between 5 to 30 °C with the specified charger designed for this battery.
Do not use the device if it has been stored at 5 °C or less. Allow it to «normalize» at room temperature before usage/charging.
Before use, place the charging base on hard, flat, stable and dry surface.
The use of attachments or accessories not recommended or sold by the product distributor may cause personal or property hazards or injuries.
Use care when operating the device by keeping all foreign objects, fingers, body parts, hair, loose clothing and jewelry away from openings.
Regularly remove blockages caused by dust, fluff, hair etc. because they greatly reduce device’s suction power and/or general performance. 20. Please refer to below paragraphs about details on cleaning, operating and settings for accessories.
Although the product has been checked its usage and consequences are strictly user responsibility.

PARTS

(see PICTURES: picture 1)

A = Dust container
B = Filter housing
C = HEPA filter
D = Main unit
E = Charging base
F = Charger (with power cable)
G =Brush
H = Crevice tool
I = indicator

BEFORE USE

Unpack all parts from packaging and assemble them together.
Charging base assembly
Step 1: Slide both parts together to lock them (“click” sound) (see PICTURES, Picture 2A).
Step 2: Plug the charger’s power cable into charging base (see PICTURES, Picture 2B).
Step 3: Guide the charger’s power cable through the side of the charging base loops (see PICTURE, Picture 2C).
Step 4: Plug the charger into the power supply socket (see PICTURE, Picture 2D).

Charging

Step 1: Slide the device into the charging base (see PICTURES, Picture 3).
Step 2: Device is charging when the indicator light (see PICTURES, picture 1) is blinking. When the light stops blinking, the charging is complete.
NOTE: For first use, charge the device for up to 6 hours and completely discharge. After first use the full charging time will be at around 4 hours.

USAGE

Press power button to turn device on in high speed mode (see PICTURES, Picture 4A, 1).
Press speed button to operate in low speed mode (or press it again for high speed mode) (see PICTURES, Picture 4A, 2).
Press power button to turn the device off.
If needed, slide the chosen attachment on the device. (see PICTURES; Picture 4B and 4C)
NOTE: For even better reach, brush can be slide on the end of crevice tool also.

CLEANING AND MAINTENANCE

It is recommended to change the HEPA filter every 3-6 months.
Device must be cleaned after each use and no later than when dust container is full.
Step 1: Press dust container release button (1) and pull out the dust container (2) (see PICTURES, Picture 5A).
Step 2: Grab and slide the filter housing with filter from the dust container (see PICTURES; Picture 5B).
Step 3: Hold the filter housing with one hand and rotate HEPA filter counter clockwise before separating them (see PICTURES; Picture 5C).
Step 4: Empty the dust all three parts (container, housing and filter) into the garbage bin.
NOTE: All three parts can be cleaned with water, but must be thoroughly dried before reassembly and further use (see PICTURES, Picture 5D).
Step 5: Slide and reinsert the assembled dust container into main device.

TROUBLESHOOTING

PROBLEM	SOLUTION
The device does not work.	Battery running low on energy. Recharge it.
The device does not vacuum properly.	Dust container is not assembled properly

to the main unit. Check and reassemble if needed.
Dust container may be full. Empty it.
Filter may be clogged. Clean it.
The device does not work properly when accessories are attached to the nonle.| Accessory may be clogged. Remove the obstruction from the accessory.
The device does not charge| Check if main unit is correctly and firmly located on the charging base and charger is correctly plugged in it and to the power supply.

TECHNICAL DATA

ROVUS NANO HAND VAC
ID: 110074447
Model number: VC3953-GS
Noise: <80 dB(A)
10,8 V DC, 120 W
Charging base
Li-ion Battery: VC3953-P-T
10,8 V; 2,0 Ah; 21,6 Wh
Battery charger: JOD-S-150050GS
Input: 100 – 240 V ~; 50/60 Hz; 0,3 A Class II
Output: 15,0 V DC 0,5 A; 7,5 W
Country of origin: P.R.C.
ORT number and production date can be found on the product.
Rovus Trademark owner, Importer to EU, Distributor:
Top Shop International SA, Via al Mulino 22, CH-6814 Cadempino, Switzerland
Average active efficiency: 80,91 %
Efficiency at low load (10%): 68,18 %
No-load power consumption: 0,068 W

Explanation of markings

This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or
human health from uncontrolled waste disposal; recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use
the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
Manufacturer’s declaration that product meets the requirements of the applicable EC directives.
Conformity with Technical regulations of the Eurasian Economic Union (EAEU) (Russia, Kazakhstan, Armenia, Kyrgyzstan and Belarus)

https://a.smart321.com/studiomodernahome
VISIT ROVUS.NET
© 2021 TOP SHOP INTERNATIONAL SA. All rights reserved.
UM-RO-110074447-NHV-A-2110

Documents / Resources

| ROVUS VC3953-GS Nano Hand Vac [pdf] User Manual
VC3953-GS Nano Hand Vac, VC3953-GS, VC3953-GS Hand Vac, Nano Hand Vac, Hand Vac, Nano Vac, Vac
---|---