ROVUS SKJ-CR021U Nano Bladeless Fan User Manual

: June 6, 2024
: ROVUS

Table of Contents

ROVUS SKJ-CR021U Nano Bladeless Fan User Manual
PICTURES
WARNINGS
1. PARTS
2. BEFORE USE
3. USAGE
4. CLEANING AND MAINTENANCE
MAINTENANCE (see PICTURES, picture 9)
STORAGE
5. TROUBLESHOOTING
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ROVUS SKJ-CR021U Nano Bladeless Fan User Manual

PICTURES

Picture 1 Picture 2

Picture 3 Picture 4

Picture 5 Picture 6

Picture 7 Picture 8

Picture 9

Please read this manual thoroughly before using and save it for future reference.

WARNINGS

This device can be used by children aged from 8 years and above as well as by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the device in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance should not be done by children unless they are older than 8 and supervised.
This device is intended for household, indoor and dry use only.
Before use, place the product on hard, flat, stable and dry surface.
If the device is not working as it should, has received a sharp blow, has been dropped, damaged, left outdoors or dropped in-to water, do not use it.
Do not attempt any modification or repair by yourself and ensure that any repair is conducted only by appropriately qualified technician.
If the power cable is damaged, it must be replaced immediately by authorized and qualified person only.
Plug in power supply that corresponds to the rated one on product only.
This product is not intended to filter oil or grease from air.
This device should never be switched on or stay plugged in power supply when not in use, while replacing accessories or during cleaning.
This device is not intended to be operated by means of an external timer or separate remotecontrol system.
Always turn off the device before unplugging it from outlet.
Do not place the power cable near a heated surface.
Never use the power cable to pick up, carry, drag, pull, or lift the air purifier. Do not pull the power cable against or around sharp corners and edges.
Use care when operating the device by keeping all foreign objects, fingers, body parts, hair, loose clothing and jewelry away from openings.
Regularly remove blockages caused by dust, fluff, hair etc. because they greatly reduce device’s suction power and/or general performance.
Never touch the device or its plug when your hands are wet.
Although the product has been checked its usage and consequences are strictly user responsibility.

1. PARTS

Main unit (see PICTURES, picture 1)
A = air outlet
B = air duct
C = air purifier filter cover
D = air inlet
E = power/function button
F = base
G = main unit
H = power socket
I = power cable
J = remote controller

Remote controller (see PICTURES, picture 2)

2. BEFORE USE

Replacing/inserting the remote controller battery (see PICTURES, picture 3).

Use only battery CR2025. Do not charge the battery.
The remote control should be pointed at the remote control signal receiver on the display to maximize the remote control signal (see PICTURES, picture 4).
NOTE: This fan may respond to the remote control of other devices. or other devices may respond. This is due to the overlapping frequencies of the remote control. There is no quality problem in the product itself. To avoid misuse, keep the remote control away from other electrical devices during operation.
Place the fan on a flat surface to avoid damage or malfunctions caused by the fan tipping over.
Make sure the air inlet is not obstructed. Stay away from the curtains to avoid objects blocking the air inlet and the fan not working.
Do not place any objects within 30 cm of the device, otherwise the blower effect will be impaired (see PICTURES, picture 5).

3. USAGE

Step 1: Plug one end of power cable to power socket and the other to power supply. “Beep” sound and LED display briefly lighting up indicate that the device is in standby mode.
Step 2: Touch the power/function button. Buzzer will beep once and the fan will start (at speed 3).
Step 3: Set the air volume by pressing »+« and »-« (on remote control) or by repeatedly touching the power/function button.
There are 9 speed settings. After few seconds display will turn off. If speed information is needed, just touch it.
Step 4: When the device is operating, press and hold the screen touch button for one second (or on remote controller).
The buzzer will beep once and the fan will start to oscillate. Press and hold the screen touch button again for one second to stop the oscillating function.
Step 5: To turn the device off, press and hold the power button for 2 seconds, the buzzer will beep twice and the fan will stop running

= The device can be switched on and off by pressing the power button.

= By pressing »max mode« button on remote controller, the display will show mark »H« and the wind strength will increase. Press it again to exit strong wing mode.
NOTE: You can also exit the current mode by pressing the »+/-» button.
= When pressing »UV sterilization« button, the display will show »U« mark. Press again to turn off the UV lamp.
= By pressing Oscillation function, the fan can swing 80⁰ left and right (see PICTURES, picture 6)). Press this button again to end the swing process.
= Press »+« button on the remote controller to increase the air volume. Press the »-« button to decrease the air volume. There are 9-speed settings.
= Press the »sleep timer« button to set 1 to 8 hours timer. After the timer function is set, other functions can be used normally. When the device is turned off, the timing setting is also canceled.
You can also adjust the angle of the fan by simply pushing the air duct forwards or backwards (see PICTURES, picture 7)

4. CLEANING AND MAINTENANCE

Replacing the filter (see PICTURES, picture 8)
Step 1: Rotate the air purifier filter cover counterclockwise to unlock, lift and remove the filter.
Step 2: Separate the old filter from the top cover.
Step 3: Place the cover on filter.
Step 4: Put the set back in the main unit and rotate the cover clockwise to secure it.

MAINTENANCE (see PICTURES, picture 9)

NOTE: Before cleaning, make sure the device is unplugged from power supply.

SURFACE: Gently wipe the fan surface with a soft, dry cloth. If the surface of the fan is dirty, dilute it with a mild detergent and wipe the surface of the fan with a soft cloth. Then wipe them off with a dry, soft cloth.
AIR INLET/OUTLET: Use a soft brush or vacuum cleaner to clean the dust at the air inlet and outlet. Too much dust, can affect fan’s efficiency.
REMOTE CONTROLLER: Gently wipe the surface of the remote control with a soft, dry cloth. If you will not use it for a long time, remove the button battery from the remote control.

STORAGE

After the fan has been cleaned and dried thoroughly it can be stored.
Keep away from vibrations and electrical devices with cooling / heating function.
Do not expose it to direct sunlight, hot and humid places.
Keep out of the reach of children.

5. TROUBLESHOOTING

PROBLEM	POSSIBLE SOLUTION
Device does not work.	Check if the device is plugged in power supply.

Check if the device is turned on.

No or decreased air flow

| Check if filter is properly installed and firmly close the filter cover.
Check the filter status and replace if necessary (too dirty).
Check to ensure nothing is blocking the air inlet and filtered air outlet.
Replace the HEPA filter if it has not been yet in the past year.
Be sure the plastic bag has been removed from the filter.