duux Beam 2 Smart Ultrasonic Humidifier User Manual
- June 10, 2024
- duux
Table of Contents
duux Beam 2 Smart Ultrasonic Humidifier
Thank you for choosing Duux. Our mission is to enhance your wellbeing by designing appealing, functional and effective products that provide you with the best possible indoor air quality.
Product Overview
- Large water tank capacity of 5 liters
- High mist output of 350 ml/h
- Built-in hygrostat and built-in temperature sensor
- Aroma tray for adding essential oils (oils not included)
- Ambient light for a cozy atmosphere
Installation & Use
General Cautions:
- Do not operate the device without water in the water tank.
- Do not move or tilt the device while it is in operation.
- Do not use the device near a heat source or in a dusty environment.
Installing the Filter:
- Take out the filter from the box.
- Remove the plastic bag from the filter holder and rinse for 5 minutes before first use.
- Lift the cover and water inlet tray to open the water tank.
- Place the filter holder in the designated position.
- Push and gently turn to fix the filter holder.
Adding Water:
- Remove the power plug and take off the lid on the top side.
- Fill the water tank with water using a watering can or container (do not exceed the transparent water inlet cover).
- Put the lid back on and plug the power cord into a wall outlet.
Using the Device:
- To switch on the device, press the power button. The display will light up.
- To adjust the mist output, use the plus (+) and minus (-) buttons on the control panel or remote control.
- To add essential oils, place them in the aroma tray.
- To turn off the device, press and hold the power button for 3 seconds.
Maintenance
Renewing Water:
- Micro-organisms that may be present in the water or in the environment where the appliance is used or stored, can grow in the water reservoir and be blown in the air causing very serious healthrisks when the water is not renewed and the tank. Renew water every 3 days.
Technical Specifications
- Power supply: AC 220-240V, 50/60Hz
- Power consumption: 30W
- Water tank capacity: 5 liters
- Mist output: 350 ml/h
FAQ
Q: Can I use tap water in the humidifier?
A: Yes, but we recommend using distilled or demineralized water to prolong the life of the device.
Q: Can I leave the device on overnight?
A: Yes, the device is designed to operate continuously for up to 14 hours.
Product Overview
To use the remote control, please lift from the dock by gently pulling out from the bottom
Installation and use
Note : Please take notice of below instructions and the separately included warning sheet before using the product.
General cautions
- Check the voltage on the device label before use. Only connect the device to sockets that correspond to the voltage of the device. If you are unsure whether your connections meet the requirements, consult an electrician or your electricity supplier.
- Do not disassemble and repair the appliance without authorization.
- If the power cord is damaged, in order to avoid danger, it must be replaced by the manufacturer or its maintenance department, and not by yourself.;
- If there is any abnormality, please unplug the power cord immediately and it must be repaired by the manufacturer or its maintenance department.
- Regularly clean the dust on the power cord plug;
- Before cleaning or moving, please turn off the power and unplug the power cord;
- When pulling the plug, hold the power plug instead of pulling the power cord;
- Do not touch the water and parts of the product while the power is on;
- Do not cover the air inlet and the mist outlet with items such as towels;
- This is not a toy. To avoid accidents, keep it away from babies and children. Do not put it in a crib, stroller or playpen. Please do not let children and babies play and use the device;
- Do not use the device on a sloping table, it should be placed in a flat and stable surface;
- Do not add flavors or similar substances produced or supervised by the company to the water tank and water tank in the device; You can use the designated aroma tray underneath the lid to add aromatherapy.
- Do not use in the kitchen. Please keep away from heat sources, avoid direct sunlight, and keep away from furniture and other household appliances 2 meters away from moisture.
- Be aware that high humidity levels may encourage the growth of biological organisms in the environment.
- Do not permit the area around the humidifier to become damp or wet. If dampness occurs, turn the output of the humidifier down. If the humidifier output volume cannot be turned down, use the humidifier intermittently. Do not allow absorbent materials, such as carpeting, curtains, drapes, or tablecloths, to become damp.
- Never leave water in the reservoir when the appliance is not in use.
Installing the filter
- Take out the filter from the box
- Remove the plastic bag from the filter holder and rinse 5 minutes before first use
- Lift the cover and water inlet tray to open the water tank
- Place the filter holder in the designated position
- Push and gently turn to fix the filter holder
Empty and clean the humidifier before storage. Clean the humidifier before
next use.
Warning : Micro-organisms that may be present in the water or in the
environment where the appliance is used or stored, can grow in the water
reservoir and be blown in the air causing very serious health risks when the
water is not renewed and the tank. Renew water every 3 days.
Installing the product
Unpack the device and remove the packing materials from the device. Store the packing materials for possible future transportation. Plug the power cord in a wall outlet. You will hear a beep and the power indicator will blink. Press the power button to switch on the device and the display will light up
Filling the water tank
Note: Always remove the plug when filling the water tank. Preferably use
clean tap- or distilled water to prevent bacteria and scale inside the water
tank.
Warning : Only fill with cold or lukewarm water. Hot or boiling water
will damage the device.
Please add water to the water tank before using the device according to the steps below:
- Remove the power plug and take off the lid on the top side;
- Fill the water tank with water using a watering can or container (do not exceed the transparent water inlet cover)
- Place back the top cover and make sure it fits properly.
- You may now switch on the device.
Note: When using the device for the first time, the water may have a slight
smell and discoloration. This is normal and not harmful for your health.
Warning : Never use any other liquid than water. Only use aroma in the
dedicated aroma tray. ****
Functions
Control panel / remote control
- Power
- Increase mist output
- Decrease mist output
- Auto mode
- Timer
- Ambient light / WIFI mode
Display
- Temperature (°C) / Humidity (%) display
- Power indicator
- Refill water indicator
- Auto mode indicator
- Mist output level bars
- WIFI indicator
- Timer indicator
- Ambient light indicator
- Timer hour(s) indicator
Power
Press the power button to switch on the device. The corresponding indicator
will light up on the display and the ambient light will switch on. The WIFI
indicator will blink to look for devices to pair. The monitoring screen will
show the actual temperature and humidity every 5 seconds. Press again to
switch off the device (the device will remain in standby mode until the plug
is removed from the wall outlet). The default humidity setting is MEDIUM
output.
Note: you can also switch on the device with the touch button on the
device, located behind the control panel / remote control.
Increase/decrease mist output
Press the button increase the mist output. The mist output level bars will
change accordingly. Pressing the button will decrease the mist output. The are
three mist output levels:
LOW , MEDIUM , HIGH
Note : The mist output setting will not cycle when pressing or button multiple times.
Auto mode
Press the button to activate the self-regulating hygrostat. The mist output
intensity will now self-regulate according to the ambient relative humidity.
Press multiple times to change the desired humidity in the following order:
40% > 45% 50% > 55% > 60% > 65% > 70% > 75% > 80% > 85% > 90% > ACTUAL
HUMIDITY > 40% > 50% > … and so on. Each press will increase with 5%. Once
released, the selected humidity will blink 3 seconds to confirm your choice.
When the hygrostat is set above the actual humidity, the device will operate
in high speed until the desired humidity has been reached. When the hygrostat
is set below the actual humidity, the device will not humidify. After setting
the hygrostat, the display will show the ambient relative humidity.
Timer
Press the key to activate the timer setting. With every touch the timer will increase with one hour in the following sequence: 1h > 2h > 4h > 6h > 8h > OFF. Once the timer is activated, the device will automatically shut down after the set timer has been completed.
Ambient light
- Press the button to active the ambient light.
- Press again to deactivate.
WIFI mode
Press and hold the button for 5 seconds to activate the WIFI mode. The indicator will quickly disappear and then flash rapidly (searching for devices to pair)
WIFI and APP operation
Scan below QR code to download the Duux APP or search DUUX APP in the App Store or Google Play Store to start the procedure to download the APP. Once installed, enter your e-mail address and complete the registration.
Connect to WIFI
- Once registered, click “add duux device” on the main screen or use the “+” button in the top right corner to add a new device.,
- Search for “Beam” and press to continue
- Connect to your preferred WiFi network and enter the corresponding password Follow the instructions in the app to complete the pairing process.
Display icons
Power
When the indicator on, the device is switched on. If it blinks, the device is
in stand-by mode
Water replacement indicator
When the indicator flashes red, it indicates that there is a water shortage.
Please remove the top cover and add water.
Auto mode
When this indicator light is on, it means the humidifier is operating in AUTO
mode.
Mist output level bars
The amount of bars determines the mist output intensity set in manual
operation mode. There are three mist output levels: LOW MEDIUM , HIGH
WIFI indicator
When the indicator light blinks, it means it’s idle and looking for a device
to pair. If it’s solid, it means the device is connected. Press and hold the
button for 5 seconds to cancel the pairing operation.
Timer indicator
When the indicator lights up, it means you have entered the timer mode. Below
you will see the number (1, 2, 4, 6 or 8H) of hours on which the timer is
activated.
Display brightness
The display will automatically dim after the last touch or press.
Water shortage
If there is no water remaining in the water tank, a beep will sound 3 times,
and the water shortage icon will automatically return to the standby state
after flashing 50 times.
Aroma tray/sponge
Below the top cover you will find a small handle which hides the aroma tray.
Lift the handle to release the tray and pour a few drops of aromatherapy on
the sponge. Place back the aroma tray and top cover to continue the operation.
Note : Only use aromatherapy that is suitable for ultrasonic humidifiers.
Other types of aromatherapy may damage the device. Refrain from using oil-
based aromatherapy at all times!
Control panel / remote control
The control panel is integrated in the remote control. When not in use, we recommend placing the remote control back in the holder on the device. Remote control batteries are included (type: AAA). Please note the polarity when inserting the batteries.
Maintenance
Important : Be sure to remove the power plug from the outlet before
carrying out maintenance.
Important : Do not soak or immerse the power plug or the device in water
- Clean water tank every 3 days
Water replacement
In order to maintain the best performance of the humidifier, the water in the water tank and the water tank itself should be cleaned every 3 days.
Cleaning
- Please use a soft cloth to wipe the dust on the body; If the surface is too dirty, it is better to wipe it clean with a damped cloth mixed with neutral detergent.
- Do not use chemical solvents, gasoline, polishing powder, etc. to clean the surface of the device.
- Do not place the device or any of it’s parts in the dishwasher to clean. It is best to clean it with clean water.
- Please use a soft cloth to clean the parts (see image) regularly. If the regular cleaning can’t remove the scale on the inside of the water tank,In order to maintain the best performance of the humidifier, the water in the water tank and the water tank itself should be cleaned every 3 days.
Cleaning
-
Please use a soft cloth to wipe the dust on the body; If the surface is too dirty, it is better to wipe it clean with a damped cloth mixed with neutral detergent.
-
Do not use chemical solvents, gasoline, polishing powder, etc. to clean the surface of the device.
Do not place the device or any of it’s parts in the dishwasher to clean. It is best to clean it with clean water. -
Please use a soft cloth to clean the parts (see image) regularly. If the regular cleaning can’t remove the scale on the inside of the water tank, mix some lemon vinegar with lukewarm water (water and lemon vinegar ratio 10ml:1g) Pour everything into a large container and let it soak for 5 minutes. Then gently scrub the scale surface with a soft brush until the scale is remove
Storage
When the appliance is not used for a long time, please clean all the
components, dry them, and put them into the original box and store them in a
dry place.
Spare parts
Spare parts and accessories can be requested at the point of purchase or local
distributor
Disposal
The European directive 2012 / 19 / CE on Waste Electrical and Electronic
Equipment (WEEE), requires that old household electrical appliances must not
be disposed of in the normal unsorted municipal waste stream. Old appliances
must be collected separately in order to optimize the recovery and recycling
of the materials they contain and reduce the impact on human health and the
environment. The crossed-out “wheeled bin” symbol on the product reminds you
of your obligation, that when you dispose of the appliance it must be
separately collected. Consumers should contact their local authority or
retailer for information concerning the correct disposal of their old
appliances.
The smart and powerful humidifier with minimal footprint
Technical specifications
The appearance and specification of the device may be changed without notice.
FAQ
The power/water supply indicator does not light up and mist does not come
out.
Insert the power plug all the way to the back of the socket or check if there
is a power cut.
The power/water supply indicator is red and the power is off, even though
the power button is pushed.?
There is not enough water. Please fill the water tank with water.
Strange noises accompany the use of the product.
A “burbling” sound comes out of the main body. This sound is the sound of
water being supplied from the water tank to the main body and does not mean
the product is defective.
A strange noise can be heard from the removed water tank.
When you remove an empty or nearly-empty water tank from the main body, an
abnormal sound from the water tank can be heard. This sound is related to
pressure within the water tank and does not mean the product is defective.
Mist can’t be seen even when the power is connected.
- Is the power/water supply display flashing red? There is insufficient water, if it is flashing red. Please fill the water tank with water.
- The mist may not be visible depending on the balance between the room temperature and humidity.
The floor is wet / There is water leakage. Is the floor wet due to
excessive humidity?
Wet floors from mist can occur due to the room environment and conditions of
use. Please switch the mist volume to minimum output or AUTO mode.
Simplified EU Declaration of conformity
Hereby, Duux declares that this environmental control radio equipment is in
compliance with Directive 2014/53/EU. The full text of the EU Declaration of
Conformity is available at the following internet address:
www.duux.com/doc
Designed in The Netherlands by Duux BV. Made in P.R.C.
Duux BV, P.O. Box 145, 5400 AC Uden Netherlands,
www.duux.com
© 2022 Duux. All rights reserved.
DUUX® is a trademark of Duux BV, registered in the EU and other countries.
The brand cited belongs exclusively to the respective owners.
Specifications are subject to modification without notice.
Version : IMDXHU1011_V2
WATCH THE INSTRUCTION MOVIES
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>