SKYDANCE T15 Wall Mounted Touch Panel User Manual

SKYDANCE T15 Wall Mounted Touch Panel User Manual

Wall Mounted Touch Panel

Model No.: T15
4 Zone/1-5 color in one/Glass touch panel/Color wheel/AC input/DMX 512 and RF 2.4G signal output

Features

• Touch panel 4 zone 1-5 color universal DMX512 master, can also be used as 4 zones 1-5 color universal RF remote.
• Each zone can be set as a single color, dual color(WW/CW), RGB, RGBW, or RGB+CCT light type.
• DMX signal output complies with standard DMX512 protocol, compatible with DMX decoder from any supplier.
• When used as RF remote, each zone can remote control multiple RF 2.4G LED controllers.
• Ultra sensitive high strength glass touch panel with touch color wheel in the middle.
• Smooth and accurate color adjustment by touching the color wheel.
• Touch keys with LED indicator. White & Black glass panels are available.

Technical Parameters

Input and Output

Safety and EMC

EMC standard (EMC)| ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
---|---
Safety standard(LVD)| EN 62368-1:2020+A11:2020
Radio Equipment(RED)| ETSI EN 300 328 V2.2.2
Certification| CE,EMC,LVD,RED

Warranty

Dimming data

Environment

Weight

Mechanical Structures and Installations

Installation diagram:

Typical base as below:

Key function

Zone light typesetting
Each zone can match single color, dual color(WW/CW), RGB, RGBW, or RGB+CCT(WW/CW) controller or lamp.
Touch the power key to turn on the light, turn off the light, then immediately long press the power key for 5 seconds, enter the zone light setting:
long press Zone 1/2/3/4 key 2 seconds, select the current zone you want to change, then long press below five key 2 seconds to change the current zone light type.

 : Long press 2 seconds, set current zone as single color type.
 : Long press 2 seconds, set current zone as dual color type.
 : Long press 2 seconds, set current zone as RGB color type.
 : Long press 2 seconds, set current zone as RGBW type.
 : Long press 2 seconds, set current zone as RGB+CCT type.
For example, If you want to change zone 1 light type as RGB type, please long press Zone 1 key 2 seconds firstly, then long press  2 seconds will set Zone 1 as RGB type.
When in zone light type setting state, all above long press key operation, the LED indicator will lighten red and blue. Short press power key or touch color wheel, or timeout 10s, quit zone light type setting.
 Turn on/off all zone lights.
 RGB color / Color temperature. Press RGB or CCT key to switch between the RGB wheel and the CCT wheel.
 RGB color, 24 levels.
 For dual color or RGB+CCT(WW/CW), adjust the color temperature by WW/CW channel, short press 11 levels, long press 2s get max or min color temperature. For RGB, adjust the color temperature by mixing the R/G/B channel, at 11 levels. For RGBW, adjust the color temperature by adjusting W channel brightness,11 levels. long press 2s get 100% or 0% White channel brightness.
 Short press play 10 built-in dynamic mode, long press 2s run mode-cycle.
 For dynamic RGB mode, adjust speed, short press 10 levels, long press 2s get the default speed.
For static RGB color, adjust saturation, namely change current static RGB color to mixed white slowly, short press 11 levels, long press 1-6s for continuous 256 levels adjustment.
 Adjust brightness, short press 10 levels, long press 1-6s for continuous 256 levels adjustment.
Short press replay scene. Long press 2s to save the current color into the scene.
4 zone recall or save synchronously.

Short press turn on zone light and select zone simultaneously, long press 2s turn off zone light. 4 zone control separately or synchronously, each zone could control multiple receivers. Only multiple zones with have same light type can select synchronously.
Note:

• For single color, touch RGB/CCT wheel only change brightness, RGB, MODE, SPEED key is invalid.
• For dual color, touch RGB/CCT wheel only change color temperature, RGB, MODE, SPEED key is invalid.
• For RGB, when touching the CCT wheel, adjust the color temperature by mixing the R/G/B channel.
• For RGBW, when touching the CCT wheel, adjust the W channel brightness.
• Turn on key tone: Long press power key 10s when all zone light is off, will turn on or turn off tone.

Touch Panel work as DMX512 Master

After connecting with DMX decoders, please set the DMX decoder’s address as below:

Light Type| Light color channel| Zone 1
DMX address| Zone 2
DMX address| Zone 3
DMX address| Zone 4
DMX address
---|---|---|---|---|---
Single color| W   W   W    W    W| 5-Jan| 10-Jun| 15-Nov| 16 – 20
Dual color| WW  CW  WW  CW    0| 5-Jan| 10-Jun| 15-Nov| 16 – 20
RGB| R    G    B   0    0| 5-Jan| 10-Jun| 15-Nov| 16 – 20
RGBW| R  G    B   W    W| 5-Jan| 10-Jun| 15-Nov| 16 – 20
RGB+CCT| R     G  B  WW   CW| 5-Jan| 10-Jun| 15-Nov| 16 – 20

Touch Panel work as RF remote

The touch panel 4 zone remote can match with the RF controller for single color, dual color(WW/CW), RGB, RGBW, or RGB+CCT light types. The end users can choose the suitable match/delete ways. Two options are offered for selection:
Use the controller’s Match key
Match:  Short press the match key, and immediately press the zone key of the touch panel. The LED indicator fast flash a few times means the match is successful.
Delete:  Press and hold the match key for 5s to delete all match, The LED indicator fast flash a few times means all matched remotes were deleted.
Use Power Restart
Match:  Switch off the power of the receiver, then switch on the power, and repeat again. Immediately short press the zone key 3 times on the touch panel. The light blinks 3 times means the match is successful.
Delete:  Switch off the power of the receiver, then switch on the power, and repeat again.
Immediately short press the zone key 5 times on the touch panel. The light blinks 5 times means all matched remotes were deleted.

Wiring Diagram

Dynamic mode list

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>