AVARRO 0E-HDMICONV2 HDMI Audio Extractor User Manual
- June 8, 2024
- AVARRO
Table of Contents
AVARRO 0E-HDMICONV2 HDMI Audio Extractor
Introduction
Overview
This product is an HDMI 2.0 audio extractor with resolutions up to 4K@60Hz
(Chroma sub-sampling 4:4:4 8bit) and HDCP 2.2. Its digital or analog audio
output allows audio to be de-embedded from HDMI input and sent to audio
distribution system, such as AVR or Amplifier. Third-gear slide switch for
audio setting in EDID has 3 EDID (pass-through, 2.0 CH and 5.1 CH) presets for
EDID management. By auto-detecting input signal status, it could automatically
trigger CEC command to turn on or off TV with CEC support. It can be used in
any AV application, such as homes, offices, digital entertainment centers,
control centers, conference rooms, schools and corporate training environments
which need HDMI audio extraction.
Features
- HDMI 2.0 up to 4K@60Hz 4:4:4 8bit.
- HDCP 2.2 compliant.
- HDMI audio de-embedded out with S/PDIF (Toslink) and L/R audio (RCA).
- Compact appearance, and easy to install.
- Third-gear slide switch for audio setting in EDID: pass-through, 2.0 CH and 5.1 CH.
- Built-in CEC controller from HDMI out.
- Automatic input cable equalization and signal regeneration compensation.
Package Contents
Before you start the installation of the product, please check the package contents:
- 1 x 0E-HDMICONV2 Extractor
- 1 x DC 5V Power Adapter with US Pins
- 2 x Mounting Brackets (with Screws)
- 1 x User Manual
Panel
No. | Name | Description |
---|---|---|
1 | HDMI OUT | Connect to an HDMI display. |
2
| S/PDIF OUT| HDMI digital audio de-embedded out, connect to an
audio distribution system such as amplifier.
3
| AUDIO OUT
(L and R)
| HDMI analog audio de-embedded out, connect to L/R channel of audio distribution system such as speaker.
Note: 2 x RCA for L/R output, supports PCM 2.0 only.
Rear Panel
No. | Name | Description |
---|---|---|
1 | DC 5V | Connect to the power adapter provided. |
2
|
POWER LED
| ON: The device is powered on.
OFF: The device is powered off.
3| HDMI IN| Connect to an HDMI source.
4
|
EDID
| Slide Switch for EDID Management.
Note : More information, please refer to “EDID Management” section.
Specification
Technical
Input/Output Port| 1 x HDMI IN, 1 x HDMI OUT, 1 x S/PDIF OUT, 1 x AUDIO
OUT (L&R RCA Connecter), 1 x DC 5V IN
Input/Output Video
Signal Type
| HDMI up to 4K@60Hz 4:4:4 8 bit with HDCP 2.2
Input Resolution Supported
| VESA:
800×6008, 1024×7688, 1280×7688, 1280×8008, 1280×9608,
1280×10248, 1360×7688, 1366×7688, 1440×9008,
1600×9008, 1600×12008, 1680×10508, 1920×12008 SMPTE:
720x480P7,8, 720x576P6, 1280x720P6,7,8, 1920x1080P6,7,8,
3840x2160P2,3,5,6,8, 4096x2160P2,3,5,6,8
1 = at 23.98 Hz, 2 = at 24 Hz, 3 = at 25 Hz, 4 = at 29.97
Hz, 5 = at 30 Hz, 6 = at 50 Hz, 7 = at 59.94 Hz, 8 = 60 Hz
Output Resolution
Supported
| VESA:
800×6008, 1024×7688, 1280×7688, 1280×8008, 1280×9608,
Technical
| 1280×10248, 1360×7688, 1366×7688, 1400×10508,
1440×9008, 1600×9008, 1600×12008, 1680×10508,
1920×12008 SMPTE:
720x480P8, 720x576P6, 1280x720P6,8,
1920x1080P1,2,3,4,5,6,7,8, 3840x2160P2,3,5,6,8,
4096x2160P2,3,5,6,8
1 = at 23.98 Hz, 2 = at 24 Hz, 3 = at 25 Hz, 4 = at 29.97
Hz, 5 = at 30 Hz, 6 = at 50 Hz, 7 = at 59.94 Hz, 8 = 60 Hz
Maximum Data Rate| 18Gbps
Maximum Pixel Clock| 600MHz
Audio Format
| SPDIF OUT: PCM 2.0, up to Dolby Digital and DTS 5.1 AUDIO (L/R) OUT: PCM 2.0
HDMI IN/OUT: PCM 2.0/5.1/7.1, Dolby True HD and DTS
HD Master Audio
General
Operating Temperature| 0°C to 45°C (32°F to 113°F)
Storage Temperature| -20°C to 70°C (-4°F to 158°F)
Humidity| 10% to 90%, non-condensing
ESD Protection
| Human-body Model:
±8kV (Air-gap discharge)/
±4kV (Contact discharge)
Power Supply| DC 5V 1A
Power Consumption (Max)| 2.88W
Device Dimension
(W x H x D)
| 8.0cm x 2.2cm x 9.0cm/3.15” x 0.87” x 3.54”
Product Weight| 0.23kg/0.51lb
Transmission Distance
Cable Type | Range | Supported Video |
---|
HDMI
| Input/Output: 15m/49ft| 1080P@60Hz
Input: 5m/16ft
Output: 10m/33ft
| 4K@60Hz 4:2:0
Input/Output: 5m/16ft| 4K@60Hz 4:4:4
Installation and Wiring
Brackets Installation
Note: Before installation, please ensure the device is disconnected from the power source.
Steps to install the device in a suitable location:
- Attach the installation bracket to the enclosure using the screws provided in the package separately.
- The bracket is attached to the enclosure as shown.
- Repeat steps from 1 to 2 for the other side of the unit.
- Attach the brackets to the surface you want to hold the unit against using the screws (provided by others).
Wiring
Warnings:
- Before wiring, disconnect the power from the device.
- During wiring, connect and disconnect the cables gently.
Steps for device wiring
- Connect an HDMI source (such as Apple TX, STB, Xbox, Media player, Blu-ray player, etc.) to HDMI IN port.
- Connect an HDMI display (TV, Monitor, Projector, etc.) to HDMI OUT port.
- Connect a digital audio distribution system (such as an amplifier) to S/PDIF OUT port.
- Connect to an analog distribution system (such as a speaker) to AUDIO OUT port.
- Note: Connect L port to left channel, and connect R port to right channel.
- Connect to the power adapter provided.
- Power on all devices.
EDID Management
EDID (Extended Display Identification Data) is a data structure provided by a
digital display to describe its capabilities to a video source.
The device features EDID management, should any device compatibility issues
occur during installation, please refer to the table below and set up the EDID
slide switch manually.
By default, the slide switch is set to “PASS” position.
Position | Descriptions |
---|---|
PASS (Default) | Allows EDID pass-through from the display to the source for |
optimal video and audio outputs to the display.
2.0 CH| Transfers 2.0 CH EDID of device to the source for
Optimum video and 2.0 CH audio outputs to the display.
5.1 CH| Transfers 5.1 CH EDID of the device to the source for Optimum video and 5.1 CH audio outputs to the display.
Note:
- If EDID Copy fails, a fixed 1920 x 1080P@60Hz 2.0 CH would be provided to source device.
- In order to achieve a better user experience, please refer to the following audio support descriptions and examples for EDID setting during installation.
Examples:
- Set the EDID switch to PASS (default) position——Copy EDID from HDMI OUT.
Display’s EDID| HDMI Output Audio| SPDIF Output Audio| L/R Output Audio
---|---|---|---
Dolby /DTS 7.1| Dolby/DTS 7.1| No Signal| No Signal
Dolby/DTS 5.1| Dolby/DTS 5.1| Dolby/DTS 5.1| No Signal
PCM 7.1| PCM 7.1| PCM 2.0| PCM 2.0
PCM 5.1| PCM 5.1| PCM 2.0| PCM 2.0
PCM 2.0| PCM 2.0| PCM 2.0| PCM 2.0
In the “PASS” position, when connected to a TV with 1080P, DTS 5.1 EDID, the device transmits the 1080P, DTS 5.1 signal to the TV, the S/PDIF output audio is DTS 5.1, while L/R output has no audio signal.
- Set the EDID to 2.0 CH position——for 2.0 CH audio output.
Display’s EDID| SPDIF Output Audio| L/R Output Audio
---|---|---
Dolby/DTS 7.1
Dolby/DTS 5.1 PCM 7.1/5.1/2.0
|
PCM 2.0
|
PCM 2.0
In “2.0 CH” position, when connected to a TV with 1080P, DTS 5.1 EDID, the device transmits the 1080P, PCM 2.0 signal to the TV, both S/PDIF and L/R output audio are PCM 2.0.
- Set the EDID to 5.1 CH position——for 5.1 CH audio output.
Display’s EDID| HDMI Output Audio| SPDIF Output Audio| L/R Output Audio
---|---|---|---
Dolby /DTS 7.1| Dolby/DTS 5.1| Dolby/ DTS 5.1| No Signal
Dolby/DTS 5.1| Dolby/DTS 5.1| Dolby/ DTS 5.1| No Signal
Limited Warranty
General
Subject to the terms and conditions of this Limited Warranty, from the date of
sale through the period of time for product categories specified in Section
1(b), ADI warrants AVARRO branded products to be free from defects in
materials and workmanship under normal use and service, normal wear and tear
excepted. Except as required by law, this Limited Warranty is only made to
Buyer and may not be transferred to any third party. ADI shall have no
obligation under this Limited Warranty or otherwise if:
- The product is improperly installed, applied or maintained;
- The product is installed outside of stated operating parameters, altered, or improperly services or repaired;
- Damage is caused by outside natural occurrences, such as lightning, power surges, fire, floods, acts of nature, or the like.
- Defects resulting from unauthorized modification, misuse, vandalism, or other causes unrelated to defective materials or workmanship, or failures related to batteries of any type used in connection with the products sold hereunder.
ADI only warrants those products branded AVARRO and sold by ADI. Any other products branded by third parties are warranted by the third party manufacturer for a period as defined by the third party manufacturer, and ADI assigns to Buyer those warranties and only those warranties extended by such third party manufacturers or vendors for non-ADI branded products. ADI does not itself warrant any non-ADI branded product and sells only on an as is basis in accordance with ADI’s terms and conditions of sale.
Specific Warranties for product categories are as follows:
Product Categories | Warranty Period |
---|---|
HDMI Distribution | 2 years |
EXCLUSION OF WARRANTIES, LIMITATION OF LIABILITY
THERE ARE NO WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, OF MERCHANTABILITY,
OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE
DESCRIPTION ON THE FACE HEREOF. TO THE FULLEST EXTENT PERMITTED BY LAW, IN NO
CASE SHALL ADI BE LIABLE TO ANYONE FOR ANY (I) CONSEQUENTIAL, INCIDENTAL,
INDIRECT, SPECIAL, OR PUNITIVE DAMAGES ARISING OUT OF OR RELATING IN ANY WAY
TO THE PRODUCT AND.OR FOR BREACH OF THIS OR ANY OTHER WARRANTY OR CONDITION,
EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF
THE LOSS OR DAMAGE IS CAUSED BY ADI’S OWN NEGLIGENCE OR FAULT AND EVEN IF ADI
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSSES OR DAMAGES.
Any product description (whether in writing or made orally by ADI or ADI’s agents), specifications, samples, models, bulletin, drawings, diagrams, engineering sheets, or similar materials used in connection with the Buyer’s order are for the sole purpose of identifying ADI’s products and shall not be construed as an express warranty or condition. Any suggestions by ADI or ADI’s agents regarding use, applications or suitability of the products shall not be construed as an express warranty or condition unless confirmed to be such in writing by ADI. ADI does not represent that the products it sells may not be compromised or circumvented; that the products will prevent any personal injury or property loss by burglary, robbery, fire or otherwise, or that the products will in all cases provide adequate warning or protection. Buyer understands and will cause its customer to understand that a properly installed and maintained product is not insurance or guarantee that such will not cause or lead to personal injury or property loss.
CONSEQUENTLY, ADI SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON ANY CLAIM AT ALL INCLUDING A CLAIM THAT THE PRODUCT FAILED TO GIVE WARNING.
However, if ADI is held liable whether directly or indirectly for any loss or damage with respect to the products it sells, regardless of cause or origin, its maximum liability shall not in any case exceed the purchase price of the product, which shall be fixed as liquidated damages and not as a penalty and shall be the complete and exclusive remedy against ADI.
Limitation on Liability to Buyer’s Customers.
Buyer agrees to limit liability to its customers to the fullest extent
permitted by law. Buyer acknowledges that ADI shall only be deemed to give
consumers of its products such statutory warranties as may be required by law
and at no time shall Buyer represent to its customers and/or users of ADI
products that ADI provides any additional warranties. By accepting the
products, to the fullest extent permitted by law, Buyer assumes all liability
for, and agrees to indemnity and hold ADI harmless against and defend ADI
from, any and all suits, claims, demands, causes of action and judgments
relating to damages, whether for personal injury or to personal property,
suffered by any person, firm, corporation or business association, including
but not limited to, Buyer’s customers and/or users of the products because of
any failure of the products to detect and/or warn of the danger for which the
goods were designed or any other failure of the products whether or not such
damages are caused or contributed to by the sold or joint concurring
negligence or fault of ADI.
Returns
Subject to the terms and conditions listed below, during the applicable
warranty period, ADI will replace Product or provide a credit at purchase at
its sole option free of charge any defective products returned prepaid. Any
obligations of ADI to replace Limited Lifetime warranty products pursuant to
this warranty which result from defect are limited to the availability of
replacement product. ADI reserves the right to replace any such products with
the then currently available products, or provide a credit in its sole
discretion. In the event Buyer has a problem with any ADI product, please call
your local ADI branch for return instructions:
- For US call 1-800-233-6261
- For Canada call 877-234-7378
- For Puerto Rico call 787-793-8830
Be sure to have the model number and the nature of the problem available. In the event of replacement, the return product will be credited to Buyer’s account and a new invoice issued for the replacement item. ADI reserves the right to issue a credit only in lieu of replacement. If any AVARRO branded products are found to be in good working order or such product’s inability to function properly is a result of user damage or abuse, the product will be returned to Buyer in the same condition as received and Buyer shall be responsible for any return freight changes.
Governing Law
The laws of State of New York apply to this Limited Warranty.
Miscellaneous
Where any term of this Limited Warranty is prohibited by such laws, it shall
be null and void, but the remainder of the Limited Warranty shall remain in
full force and effect.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>