AVARRO 0E-HDMIEX4KR HDMI Extender Bi-Directional Poe User Manual

AVARRO 0E-HDMIEX4KR HDMI Extender Bi-Directional Poe User Manual

Introduction

Overview
This product is an HDBaseT extender, and it is designed to extend 4K HDMI signals up to 70m/230ft via a single Cat 5e/6 cable and 100m/330ft via a single Cat 6a/7 cable.
The transmitter and receiver just need a single power supply to power both devices via its bi-directional PoC function.
The extender also supports bi-directional IR pass-through and RS232 pass- through.
With bidirectional ethernet pass-through supported, connect a PC to the Ethernet port of transmitter/receiver, and connect ethernet port of receiver/transmitter to the local area network, the PC can access to the local area network.
The extender is easy to install and space saving, offering solutions for home, office, digital entertainment centers, control centers, conference rooms, school and corporate training environments.

Features

• Slim profile, space saving and easy-to-install.
• 4K/UHD capability @60Hz with 4:2:0 8bit Chroma sampling.
• HDCP 2.2 compliant.
• Supports signal transmission up to 100 meters (4K and 1080P) via a single Cat 6a/7 cable.
• Supports signal transmission up to 70 meters (4K) and up to 100 meters (1080P) via a single Cat 5e/6 cable.
• Supports RS232, IR and Ethernet signals pass-through over HDBT.
• Bi-directional PoC, one power adapter at either transmitter or receiver side can power both units.

Package Contents

Before you start the installation of the product, please check the package contents:

• 1 x 0E-HDMIEX4KR Transmitter
• 1 x 0E-HDMIEX4KR Receiver
• 1 x DC 18V Power Adapter with US Pins
• 1 x IR Emitter
• 1 x Broadband IR Receiver (30-50KHz)
• 2 x Phoenix Male Connecter (3.5mm 3-Pin)
• 4 x Mounting Brackets (with Screws)
• 1 x User Manual

Panel

Transmitter

Front Panel

OFF: The transmitter is powered off.
2| STATUS
LED| FLASHING SLOWLY: The transmitter is working properly.
OFF: The transmitter is not working properly.
3| LINK LED| ON: Transmitter and Receiver are linked. BLINKING: Connection exception.

OFF: No link.

4| HDCP LED| ON: HDCP protected content is being transmitted.
BLINKING: Non-HDCP protected content is being transmitted.
OFF: No content is being transmitted.

Rear Panel

With bi-directional PoC supported, one power adapter is needed to be connected to transmitter or receiver to power both units.
2| HDBT OUT| Connect to the HDBT IN port of the receiver.
3| IR IN| Connect to the IR receiver.
4| IR OUT| Connect to the IR emitter.
5| RS232| Connect to a RS232 device for pass-through or connect to a PC for firmware upgrading.
6| HDMI IN| Connect to an HDMI source.
7| ETHERNET| Connect to a network access point or a network terminal device.
8| MODE| NORMAL: For RS232 pass-through.
UPDATE: For firmware upgrade.

Receiver

Front Panel

OFF: The receiver is powered off.
2| STATUS
LED| FLASHING SLOWLY: The Receiver is working properly.
OFF: The Receiver is not working properly.
3| LINK LED| ON: Transmitter and Receiver are linked.
BLINKING: Connection exception.
OFF: No link.
4| HDCP LED| ON: HDCP video is being transmitted.
BLINKING: Non-HDCP video is being transmitted.
OFF: No HDMI signal.
---|---|---

Rear Panel

With bi-directional PoC supported, one power adapter is needed to be connected to transmitter or receiver to power both units.
2| HDBT IN| Connect to the HDBT OUT port of the transmitter.
3| IR IN| Connect to the IR receiver.
4| IR OUT| Connect to the IR emitter.
5| RS232| Connect to a RS232 device for pass-through or connect to a PC for firmware upgrading.
6| HDMI OUT| Connect to an HDMI display.
7| ETHERNET| Connect to a network access point or a network terminal device.
8| MODE| NORMAL: For RS232 pass-through.
UPDATE: For firmware upgrade.

Specification

Technical

Input/output Port| Transmitter: 1 x HDMI IN, 1 x HDBT OUT, 1 x IR IN,
1 x IR OUT, 1 x RS232, 1 x ETHERNET, 1 x DC 18V IN
Receiver: 1 x HDMI OUT, 1 x HDBT IN, 1 x IR IN,
1 x IR OUT, 1 x RS232, 1 x ETHERNET, 1 x DC 18V IN
Video Signal Type| HDMI 1.4 with 4K@60Hz 4:2:0 8bit, HDCP 2.2
Input/output Resolution

Support

| 4K@60 4:2:0 8bit
/1080P/1080i/720P/576P/480P/576i/480i
Audio Format| Supports multichannel audio up to PCM 7.1, Dolby True
Technical

Supported| HD, DTS HD Master Audio, Dolby Atmos and DTS:X
Maximum Data Rate| 10.2Gbps
Maximum Pixel Clock| 340MHz
General

Operating Temperature| 0°C to + 45°C (32 to + 113 °F)
Storage Temperature| -20 to +70°C (-4 to + 158 °F)
Humidity| 20% to 90%, non-condensing
ESD Protection| ±8kV (Air-gap discharge)/
±4kV (Contact discharge)
Surge Protection| Voltage: ±1 kV
Power Supply| DC 18V 1A
Power Consumption (Maximum)| RX is powered by TX: 13W TX is powered by RX: 12.2W
TX and RX are powered separately:
TX: 5.5W, RX: 7.6W
Device Dimensions: (W x H x D)| Transmitter/Receiver: 13.5 cm × 1.49 cm ×7.42 cm/5.31” x 0.59” x 2.92”
Product Weight| Transmitter/Receiver: 0.24kg/0.53lb

Transmission Distance

Note: We recommend the use of T568B straight-through category cables.

1080P@60 Hz 3D
4K2K@30Hz 4:4:4
4K@60Hz 4:2:0
Cat 6a/7| 100m/330ft
HDMI| Input/Output: 10m/33ft| 4K2K@30Hz 4:4:4
4K@60Hz 4:2:0

Installation and Wiring

Brackets Installation

Note: Before installation, please ensure the device is disconnected from the power source

Steps to install the device in a suitable location:

1. Attach the installation bracket to the enclosure using the screws that were provided in the package separately.
2. The bracket is attached to the enclosure as shown.
3. Repeat steps from 1 to 2 for the other side of the transmitter.
4. Attach the brackets to the surface you want to hold the transmitter against using the screws (provided by others).
5. Repeat steps from 1 to 4 to install the receiver.

Wiring

Warnings:

• Before wiring, disconnect the power from the device.
• During wiring, connect and disconnect the cables gently.

Steps for device wiring:

1. Connect an HDMI source (such as Blu-ray player) to HDMI IN port of the transmitter.
2. Connect HDBT OUT port of transmitter to HDBT IN port of receiver using a Cat 5e/6/6a/7 cable.
3. Connect an HDMI display (such as TV) to HDMI OUT port of the receiver.
4. Connect the provided IR emitter cable to IR OUT port of the transmitter/receiver, and connect the provided IR receiver cable to IR IN port of the receiver/transmitter. The source remote can control the source at receiver side or the display remote can control the display at the transmitter side.
5. Connect the provided power adapter to the transmitter or receiver. With bi-directional PoC function supported, only one power adapter is needed to power both units.
6. Power on all attached devices.
   

Operation

You can use a RS232 port on Transmitter and Receiver to connect to a computer to update firmware or connect a RS232 device to communicate with another RS232 device on the other extender’s side via a Cat 5e/6/6a/7 cable.

Scenario 1
Slide “MODE” switch of TX/RX to “UPDATE” side, connect a PC to RS232 port of TX/RX to upgrade it.

Scenario 2
Slide “MODE” switches of TX/RX to “NORMAL” side, connect RS232 devices to RS232 ports of TX/RX.

Limited Warranty

Limited Warranty

• General
  Subject to the terms and conditions of this Limited Warranty, from the date of sale through the period of time for product categories specified in Section 1(b), ADI warrants AVARRO branded products to be free from defects in materials and workmanship under normal use and service, normal wear and tear excepted. Except as required by law, this Limited Warranty is only made to Buyer and may not be transferred to any third party.

ADI shall have no obligation under this Limited Warranty or otherwise if:

• The product is improperly installed, applied or maintained;
• The product is installed outside of stated operating parameters, altered, or improperly services or repaired;
• Damage is caused by outside natural occurrences, such as lightning, power surges, fire, floods, acts of nature, or the like.
• Defects resulting from unauthorized modification, misuse, vandalism, or other causes unrelated to defective materials or workmanship, or failures related to batteries of any type used in connection with the products sold hereunder.

ADI only warrants those products branded AVARRO and sold by ADI. Any other products branded by third parties are warranted by the third party manufacturer for a period as defined by the third party manufacturer, and ADI assigns to Buyer those warranties and only those warranties extended by such third party manufacturers or vendors for non-ADI branded products. ADI does not itself warrant any non-ADI branded product and sells only on an as is basis in accordance with ADI’s terms and conditions of sale.

Specific Warranties for product categories are as follows:

EXCLUSION OF WARRANTIES, LIMITATION OF LIABILITY

THERE ARE NO WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. TO THE FULLEST EXTENT PERMITTED BY LAW, IN NO CASE SHALL ADI BE LIABLE TO ANYONE FOR ANY (I) CONSEQUENTIAL, INCIDENTAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES ARISING OUT OF OR RELATING IN ANY WAY TO THE PRODUCT AND.OR FOR BREACH OF THIS OR ANY OTHER WARRANTY OR CONDITION, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY ADI’S OWN NEGLIGENCE OR FAULT AND EVEN IF ADI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSSES OR DAMAGES.

Any product description (whether in writing or made orally by ADI or ADI’s agents), specifications, samples, models, bulletin, drawings, diagrams, engineering sheets, or similar materials used in connection with the Buyer’s order are for the sole purpose of identifying ADI’s products and shall not be construed as an express warranty or condition. Any suggestions by ADI or ADI’s agents regarding use, applications or suitability of the products shall not be construed as an express warranty or condition unless confirmed to be such in writing by ADI. ADI does not represent that the products it sells may not be compromised or circumvented; that the products will prevent any personal injury or property loss by burglary, robbery, fire or otherwise, or that the products will in all cases provide adequate warning or protection. Buyer understands and will cause its customer to understand that a properly installed and maintained product is not insurance or guarantee that such will not cause or lead to personal injury or property loss.

CONSEQUENTLY, ADI SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON ANY CLAIM AT ALL INCLUDING A CLAIM THAT THE PRODUCT FAILED TO GIVE WARNING.

However, if ADI is held liable whether directly or indirectly for any loss or damage with respect to the products it sells, regardless of cause or origin, its maximum liability shall not in any case exceed the purchase price of
the product, which shall be fixed as liquidated damages and not as a penalty

Limitation on Liability to Buyer’s Customers.
Buyer agrees to limit liability to its customers to the fullest extent permitted by law. Buyer acknowledges that ADI shall only be deemed to give consumers of its products such statutory warranties as may be required by law and at no time shall Buyer represent to its customers and/or users of ADI products that ADI provides any additional warranties. By accepting the products, to the fullest extent permitted by law, Buyer assumes all liability for, and agrees to indemnity and hold ADI harmless against and defend ADI from, any and all suits, claims, demands, causes of action and judgments relating to damages, whether for personal injury or to personal property, suffered by any person, firm, corporation or business association, including but not limited to, Buyer’s customers and/or users of the products because of any failure of the products to detect and/or warn of the danger for which the goods were designed or any other failure of the products whether or not such damages are caused or contributed to by the sold or joint concurring negligence or fault of ADI.

Returns
Subject to the terms and conditions listed below, during the applicable warranty period, ADI will replace Product or provide a credit at purchase at its sole option free of charge any defective products returned prepaid. Any obligations of ADI to replace Limited Lifetime warranty products pursuant to this warranty which result from defect are limited to the availability of replacement product. ADI reserves the right to replace any such products with the then currently available products, or provide a credit in its sole discretion. In the event Buyer has a problem with any ADI product, please call your local ADI branch for return
instructions:

Be sure to have the model number and the nature of the problem available. In the event of replacement, the return product will be credited to Buyer’s account and a new invoice issued for the replacement item. ADI reserves the right to issue a credit only in lieu of replacement.
If any AVARRO branded products are found to be in good working order or such product’s inability to function properly is a result of user damage or abuse, the product will be returned to Buyer in the same condition as received and Buyer shall be responsible for any return freight changes.

Governing Law
The laws of State of New York apply to this Limited Warranty.

Miscellaneous
Where any term of this Limited Warranty is prohibited by such laws, it shall be null and void, but the remainder of the Limited Warranty shall remain in full force an effect.

CUSTOMER SUPPORT

For US call 1-800-233-6261
For Canada call 877-234-7378
For Puerto Rico call 787-793-8830

References

• AVARRO

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>