PNi HS650 Wireless Alarm System User Manual

PNi HS650 Wireless Alarm System User Manual

Warnings

Before using this product, please read the user manual carefully. The installation and configuration of this alarm system require basic technical knowledge to allow a correct understanding of the technical terms and procedures described in this manual. Follow the step by step instructions and start with simple settings. After making the settings, test the correct operation of the product.

Main functions

• 4.3 inch color IPS touch screen
• Remote control via Tuya Smart application (Android/iOS)
• Menu and voice prompts in 9 languages
• Built-in siren, wired indoor siren included in the package and the possibility of pairing a wireless outdoor siren
• Up to 90 wireless zones (sensors) and 3 wired zones (EOLR)
• Up to 8 smart sockets or relays
• Supports renaming areas, for example: door, bedroom, window, balcony, living room, smoke sensor, gas sensor, CO sensor, etc.
• Low battery warning for sensors
• Event log
• Alarm alert sent by phone call or SMS on preset phone numbers (up to 5 phone numbers can be set)
• Direct phone call via GSM
• Built-in tamper
• GSM 4G and WiFi communication
• Automatic time synchronization via GSM and WiFi
• System configuration via SMS
• Recorded alarm messages (up to 20 seconds/message)
• Remote arming/disarming via Tuya Smart application
• Scheduled arming/disarming

General information

Burglary protection

Your alarm system has two modes of protection against burglary: Home arming and Total arming. Home arming (perimeter arming) only protects the perimeter, allowing you to move freely inside the house.  Total arming protects the entire building.

Zones

The sensors paired to your alarm system will be assigned to different “zones” (maximum 90 for wireless sensors and maximum 3 for wired sensors). For
example, the sensor on the front door of the house can be assigned to zone 01, the sensor on the window in the master bedroom in zone 02 and so on. The zone number is displayed on the screen when an alarm or problem occurs on a specific area.

Entry and Exit Delay

Your alarm system has been programmed with adjustable delay time that allows
you to leave the house after arming the system and d sarm the system at the entrance into the house, without triggering an alarm. If you leave the house too late after arming the system or disarm the system too late after entering the house, the system will trigger an alarm. Disarm the system immediately.

The alarm and the event notifications on the phone

When an alarm is triggered, the built-in and the external siren will sound until
the system is disarmed or until the preset time interval for the siren expires.
message will show up on the control panel screen with the area or areas where the alarm was triggered. If set, the alarm system will call or send SMS via the 4G GSM network to the preset phone numbers (maximum 5) or will send notification via the mobile application (Tuya Smart)

Alarm system control via Tuya Smart application

Download the Tuya Smart app via Google Play or App Store or scanning the
QR codes below:

Android

iOS

• Open the application, create an account and log in.
• Add your device by clicking the + icon in the upper right corner of the screen or by clicking the Add device button (this button only appears when you do not have any devices added to the application).
• Select the Sensors option on the left side of the screen.
• From the list of devices, select Alarm (Wi-Fi)
• Select the WiFi network you want to connect to and add the password.
• In the next interface, select the option EZ Mode from the upper right corner.
• Access the alarm system control panel menu WiFi- >AirLink Configure
• Then tick Confirm the indicator is blinking rapidly. Click Next.
• The application will start scanning the nearby devices.
• After it identifies your device, you will receive the confirmation Added Successfully.
• To finish, click the button Done

The application allows you to add accessories (remote controls and sensors), to configure the system, to arm and disarm, to view the history log. For details about the menu in the application, please read the explanations of the alarm menu .

Main unit

Package contents:

• 1 x control unit
• 1 x wireless motion sensor
• 1 x wireless magnetic sensor
• 1 x wired indoor siren
• 2 x remote controls
• 2 x RFID TAGs
• 230V – 5V power adapter with USB
• USB – microUSB power cable
• Mounting accessories

SOS button lights

Connecting wired accessories

Zone 1, Zone 2, Zone 3 and Zone 4 are the EOLR wired zones that support
devices (sensors) with NO (open circuit) and NC (closed circuit) signal with a response time of 300 ms. Maximum resistance of the area: 11000 Ohms +
EOLR
Connect the NC (Normally Closed) devices in series at the top of the loop. The
EOLR resistor must be connected in series with the devices to the last device.
Connect the NO (open circuit) devices in parallel, in the loop.

Wiring diagram

Note: EOLR (End of Line Resistor): If the EOLR resistor is not at the end of the loop, the area will not be properly monitored and the system may not respond to an open circuit in the area

Home screen

1

|

GSM status

| | Missing SIM card or defective SIM card
---|---|---|---
| GPRS – connected to server
| RSSI signal levelThe signal level is displayed by bars from 1 to 5 (weak to strong), and the bars are gray if the system is not registered in the GSM network

2

|

WiFi status

| | The system is connected to WiFi. The number of bars indicates the signal strength.
| The system is connected to the server, if the point is displayed.
3| GSM| | Outgoing SMS
| Outgoing phone call
4| Keyboard status| | Keys locked

5

|

Power supply

| | The system is powered to 230V
| 0~3 barsThe system is powered by the built- in battery. The icon is red when the battery is discharged.
6| Time| 15:44| Real time
7| Real time

7

| View system status messages| Exit delay Message “Please exit” + Count down You have xx seconds to leave the house. When the time has expired, the alarm system is armed.
7| View system status messages| Entry delay Message “Please disarm” + CountdownYou must disarm the system before the entry time expires. If the time has expired and you have not disarmed, the alarm will sound.
---|---|---
7| View system status messages| Pairing mode Message “Synchronizing” + CountdownYou must activate the wireless accessory before the pairing time expires.
7| View system status messages| Message “Alarm” or “Panic Alarm“ is displayed together with the Zone where the alarm was triggered.
8| Screen lock button
9| Date and day of the week
10| Call| | Press to access the phone number dialing interface
11| Arm| | Press to arm the system
12| Sockets| | Press to add up to 8 smart sockets
13| Alarm status| | The system is fully armed
| The system is partially armed
| The system is disarmed
13| Log| Click to see the arming/disarming history log
14| System status| | The system is in normal condition, no alarm
| The system is in alarm, it will also display the area where the alarm was triggered
15| Menu| | Press to access the menu
16| Home arming| | Press to activate partial (perimeter) arming
17| Disarming| | Press to disarm the system

Menu

Settings

Delay

| Exit Delay| Set the exit delay Between 0 ~ 65535 sec.| Default: 40 sec.
Entry Delay| Set the entry delay Between 0 ~ 65535 sec.| Default: 30 sec.
Siren Duration| Set siren duration Between 0 ~ 65535 sec.| Default: 3 minutes

Switch

| Arm Beep| Enable/Disable the beep when arming/disarming (1)| Default: Enabled
Siren| Enable/Disable the siren sound when an alarm occurs| Default: Enabled
Arm SMS| Enable/Disable SMS notification on arming/ disarming| Default: Disabled
Keypad lock| Enable/Disable the key lock function (2)| Default: Disabled
Keyboard Backlight| Enable/Disable illuminated keys(3)| Default: Enabled
Keypad tone| Enable/Disable key sound| Default: Enabled
SOS| Enable/Disable SOS button| Default: Enabled
Switch| Delay tick| Enable/Disable countdown sound at entry or exit| Default: Enabled
---|---|---|---
Door/Window open warning| Enable/Disable open window/door warning after arming (4)| Default: Enabled
Human Voice| Enable/Disable voice prompts| Default: Enabled
Password| System| Change the system password(5)| Default: 6666
User| Change the user password(6)| Default: 1234
Language| Chinese, English, German, Russian, Spanish, Polish, Italian, French, Portuguese, Greek, Romanian (7)| Default: English
Initialization| Return to factory settings. All accessories and parameters will be deleted.(8)
Phone
1st Phone, 2nd Phone, 3rd Phone, 4th Phone, 5th Phone| Input the phone number and enable or disable calling or sending an SMS in case of alarm on the respective number
Log
Alarm log| Displays the alarm history log
Arm log| Displays the history log of arming/disarming the system13
Parts

Remote| The interface allows you to add, delete a remote control or delete all remote controls
Detector| The interface allows you to add, edit or delete all sensors in the system
RFID| The interface allows you to add, delete a TAG or delete all RFID TAGs in the system
Siren Learn| Send a mating signal to a wireless siren
Alarm Socket| AirLink for pairing with a smart socket
Socket On/ Off Timer| Add a smart plug and set a daily activation program
Decoder| Displays the alarm system ID
EOL Zone| EOL Zone 1| Define a name and number of EOLR zones (wired zones)
EOL Zone 2
EOL Zone 3
EOL Zone 4
WiFi
AirLink Configure| WiFi setup (Requires smartphone app)
Unbind| Disconnect the Unit from the server
MAC/IP| Display the MAC and IP addresses of the WiFi module
SoftAP Configure| WiFi hotspot connection14
Record

Record| Audio message recording (sent by calling the preset phone numbers in case of alarm)
Play| Message playback
Delete| Delete message
Duration| Set message duration, between 0-20 sec.| Default: 20 sec.
Timer
Arm Timer| Set a daily time for automatic arming
Disarm Timer| Set a daily time for automatic disarming
Zone&Sync| It is not active.The time zone can be set via SMS. See page 23
Date&Time| Set date and time
Wi-Fi- Sync| Turn on/off time synchronization using WiFi network information| Default: On
2G/4G Sync| Turn on/off time synchronization using the GSM network information| Default: On
Version
Displays the firmware version and MAC address of the WiFi module, the firmware version and IMEI of the GSM module and the serial number of the central unit.

Footnotes

1. Arming beep : When the function is enabled, the system will announce by a sound the arming or disarming operation.
2. Key lock : If this function has been enabled, the system will automatically  lock the keyboard if no operation is performed for 30 seconds. To activate the keyboard, you must enter the user password.
3. Keys backlight : If the function is deactivated, the key backlights turn off after 30 seconds if no operation is performed.
4. Open door/window warning : If the function is enabled, the system will generate an warning notification when you open a door or window after the exit time has elapsed.
5. System password: used to unlock the keypad and make remote settings via SMS.
6. User password: used to unlock the keypad, as a prefix for remote settings via SMS and notification for alarm text.
7.   Language: the voice prompts and the notification will be in the selected language. After selecting the desired language, the panel will restart.
8. Initialization: All customized parameters will return to factory defaults and all paired sensors will be deleted.

Configuration

Power the control unit
Connect the power adapter in the package to the 5V micro USB port and move
the backup battery switch to the “ON” position.

WiFi communication through the integrated module
If your system is configured to report alarms and accept remote control via the mobile application, the wireless router the alarm system is connected to must
always be on and connected to the Internet.

GSM/4G WiFi communication through the integrated module
If your system is set up to report alarms, receive settings via SMS, or make voice
calls, make sure a SIM card is installed (see image below) and the control panel is connected to the GSM/4G network. Disable the PIN to the SIM card before adding it into the unit.

Add and configure phone numbers

You can set up to 5 phone numbers that will receive alarm notifications via SMS
or voice call.

• Go to the menu: P hone - > 1st Phone, 2nd Phone, 3rd Phone, 4th Phone, 5th Phone
• Phone number : Touch the icon to input the phone number (maximum 18 digits) using the numeric keypad
• Phone call : Press twice the icon to select between On and Off. If you select the On option, in the event of an alarm, a voice message will be sent to that phone number.
• SMS: Press twice the icon  to select between On and Off. If you select the On option, in case of an alarm, an SMS will be sent to the respective phone number.
• Press the √ key to confirm

Add/Delete remote controls

Add new remote control

• In the main menu, select: Parts->Remote

• Press to add a new remote control.

• On the screen, the message Synchronising will show up. The system enters
  the pairing mode and counts the remaining pairing time (maximum 20 sec.).

• Press a button on the remote control to send a signal to the control panel.
  On the screen, the message Device code has been learnt will show up if the remote control was successfully paired.

Delete remote control

• In the main menu, select: Parts- >Remote
• Press next to the remote control you want to delete.
• Press the √ key to confirm.

Delete all remote controls

• In the main menu, select: Parts- >Remote
• Press the key to delete all the remote controls.
• Press the √ key to confirm.

Add/Delete wireless sensors

Add sensor

• In the main menu, select: Parts->Detector
• Press the key to add a sensor.
• Touch the icon A to choose a name for the added sensor.
• Touch the icon to select the working mode of the sensor

Choose between:
Active when perimeter arming – usually assigned to sensors or magnetic
contacts on exterior (perimeter) doors and windows. The sensor is active when the system is f ully armed or partially armed. Inactive when perimeter arming – usually assigned to a sensor (eg motion
sensor) in an interior area (eg living room, hall, bedroom). The sensor remains inactive if the system is partially armed. 24 hours active – usually assigned to an area that contains an emergency button, smoke sensor, CO sensors, flood sensors and gas sensors. To use the sensor as a doorbell, select Doorbell. To deactivate the sensor, select Close.

• To deactivate the sensor, select Close.
• ouch the icon where you will be able to assign a number to that area. The area number must be unique .
• Press the key √. The message Synchronising appears on the screen. The system enters pairing mode and counts the remaining pairing time (maximum 20 sec.)
• Trigger the sensor to send a pairing signal towards the control panel.
• After pairing, the message Learning OK will be displayed.

Edit/Delete a sensor

• In the main menu, select: Parts->Detector
• Click on the number in front of the sensor you want to edit in the list of sensors. When you have finished editing the name, mode and area number, press the √ key to confirm.
• To delete, Touch the icon next to the sensor you want to delete. Press the √ key to confirm.

Delete all sensors

• In the main menu, select: Parts->Detector
• Touch the icon to delete all sensors.
• Press the √ key to confirm.

Add/Delete RFID TAGs

Add new TAG

• In the main menu, select: Parts-> RFID
• Touch the icon to add a TAG
• The message Synchronising appears on the screen. The system enters pairing mode and counts down the remaining pairing time (max. 20 sec.).
• Move the TAG closer to the RFID area marked on the control panel.
• The screen will display Device code has been learnt if the TAG was successfully paired.

Delete TAG

• In the main menu, select: Parts- > RFID
• To delete a TAG, Touch the icon next to the TAG you want to delete.
• Press the √ key to confirm.

Delete all TAGs

• In the main menu, select: Parts-> RFID
• Touch the icon to delete all TAGs.
• Press the √ key to confirm.

Pairing a wireless siren

• Switch the siren to pairing mode (see the siren user manual). Note: The wireless siren is not included in this package. Compatible product: Wireless
  outdoor siren PNI SafeHouse HS007

• In the main menu, select: Parts->Siren Learn

• The system sends a signal to the siren. The message Learn signal sent appears on the screen. The wireless siren will confirm pairing with an audible or visual signal (see the siren user manual).• Switch the siren to pairing mode (see the siren user manual). Note: The wireless siren is not included in this package. Compatible product: Wireless outdoor siren PNI SafeHouse HS007

• In the main menu, select: Parts- >Siren Learn

• The system sends a signal to the siren. The message Learn signal sent appears on the screen. The wireless siren will confirm pairing with an audible
  or visual signal (see the siren user manual).

Pairing a wireless socket or relay

• In the main menu, select: Parts->Alarm Socket
• Switch the wireless socket/relay to pairing mode (see the socket/relay
manual). The wireless socket/relay is not included in this package.
• Press the key On and Off one at a time. On the screen, the icon
appears. The system sends a signal to the socket/relay twice. The message
Learn signal sent appears on the screen.
• The wireless socket/relay will confirm the pairing. For details, refer to the
manual of the wireless socket or relay.
• To test whether the wireless device can be opened and closed, press the key
On and Off

Note: When an audible alarm is triggered, the wireless socket or relay will remain
open until the system is disarmed or the alarm time expires.

Intelligent automation Wireless socket/relay learning

• In the main menu, select: Parts- >Socket On/Off Timer
• Touch the icon  to add a new timer for a previously added socket/relay.
• Press + and – to choose the socket/relay number and to set the hour (HH) and minutes (mm).
• Press the day or days of the week in which you want the timer to be active.
• Click the icon to enable or disable timing.
• Press the √ key to confirm.

Note: You can open and close the wireless socket or relay in the Tuya Smart mobile application.

Record messages

Record and playback messages
You can record a voice message (up to 20 sec.) through your alarm system. If an
alarm is triggered, you can receive a voice call with that message on the preset
phone numbers.

• In the main menu, select: Record-> Record
• Speak in a normal tone of voice
• Recording stops automatically after the preset time has elapsed
• The system automatically plays the message
• Press the √ key to save the message

You can playback the recorded message, delete it or change its maximum
duration by accessing the options in the Record menu.

Automatic arming/disarming

You can set the daily arming and disarming at certain hours.

• Select in the main menu: Timer- > Arm Timer or Timer-> Disarm Timer
• Press + and – to set the hour (HH) and minutes (mm).
• Touch the icon  to turn timing on or off.
•  Press the √ key to confirm.

SMS configuration

You can configure the alarm system remotely via SMS.
The text of the message differs depending on the command to be sent to the
alarm system. Send the message to the SIM number installed in the alarm system. You will receive a confirmation SMS on your phone if the setting was successful.

Note: The examples below use the default administrator (system) password: 6666.

Commands and functions

• 6666 26
  33| Entry and Exit Delay query| 6666 33*
  35*| How many times a number is automaticallyredialed in case ofconnection error| 1-255 times| 1 time| 6666 35 4
  38| Set user password| Must contain 4 digits between 0000-9999| 1234| 6666 38** 2222 ***
  39**| Set system password| Must contain 4 digits between 0000-9999| 6666|
• 6666 * 38 5555 *
  43*| Initialization of parameters| Reset parameters. Remote controls, sensors and RFID TAGs added to the system remain| 6666 * *43
  ---|---|---|---
  46| Query SMS and beep settings in case of arming/disarming and alarm.In the answer received: 1 is On0 is Off| 6666 46*
  62*| Query system settings| 6666 * *62
  94| Set time zone| +8| 6666 94 +2 *****

Set phone number via SMS

Syntax of the message to be sent:
System passwordCommand1 07xxxxxxx, A,BCommand207 xxxxxxx, A,B

he * symbol marks the beginning and end of the syntax and is also used as a
separator between commands.

07xxxxxxxx, A, B
In this string:
07xxxxxxx represents the phone number (up to 18 digits)
A used to enable (1) or disable (0) the voice call in case of alarm
B used to enable (1) or disable (0) SMS notification in case of alarm used to enable (1) or disable (0) SMS notification in case of alarm

Examples:
To set the first phone number 0710123456 and to activate only the SMS
notification in case of alarm and to set the second phone number 0720654321
and to activate only the voice calling, then the SMS message to be sent to the system will have the form: 6666510710123456,0,1520720654321,1,0

In this Syntax:

• 666 is the default system (administrator) password
• 51 is the command to set the first phone number
• 0710123456 is the phone number
• 0 the phone call function is disabled
• 1 the SMS function enabled

Query phone numbers via SMS

Message syntax: 666651*
You will receive a message on the phone: PHONE set:

1. : 07xxxxxxxx, A, B
2. : 07xxxxxxxx, A, B
3. : 07xxxxxxxx, A, B
4. : 07xxxxxxxx, A, B
5. : 07xxxxxxxx, A, B

07xxxxxxxx is the phone number (up to 18 digits)
A it can be 1 or 0 , meaning the voice call in case of alarm enabled or disabled
B it can be 1 or 0 , meaning the SMS in case of alarm enabled or disabled

Query system settings via SMS

First query
Message syntax: *666662

You will receive a message on your phone:
SYSTEM set:
SN: xxxxxx (the serial number of the alarm system)
LANGUAGE: English (system language)
ENGINEER PASSWORD: 6666 (system password)
USER PASSWORD: 1234 (user password)
GSM CSQ: 17
Wi-Fi RSSI: 0

Second query
Message syntax: *666690

You will receive a message on your phone:
SYSTEM set2:
APN: CNMET (Access Point name)
GPRS IP: x.x.x.x:x (server IP and port)
NTP: …
TIME ZONE: +08:00 (time zone)
SERVER: GLOBAL

Setting the alarm system name via SMS

Message syntax: 1234@XXX
In this syntax:
1234 is the user password
@ separator
XXX is the customized text

Example: 1234@office buildings

Customize the area name via SMS

Message syntax: 1234@XX@Down Stairs

In this syntax: 1234 is  the user password
@ separator
XX isv  the number of the zone (between 01-99)
Dow n Stairsis the customized name

Example: 1234@01@office

Ma ke a voice call via the alarm system

When in the main interface, press the Call menu to dial the phone number you
want to call. Press the icon to confirm the call. Press C to delete

Arm/Disarm the alarm system Total arming

To arm the alarm system, proceed as follows:

• From the remote control: press the key
• Through the control panel: press the key
• By RFID TAG: Move the TAG closer to the RFID area marked on the control panel
• Through the Tuya Smart application: press the Arm key. Details on controlling the alarm system through the application can be found on page 5.
• SMS command. The syntax of the message to be sent to the system: 1234#1 ,  in which 1234 is the user password and 1 is the arming comman . If you have the SMS sending function activated in your phone number in case of arming, you will receive a confirmation message.

Home arming (perimeter arming)

• To home arm the alarm system, proceed as follows:
• From the remote control: press the key
• Through the control panel: press the key
• Through the Tuya Smart application: press the Home Arm key. Details on controlling the alarm system through the application can be found on page 5.
• By SMS command. The syntax of the message to be sent to the system: 1234#3 , where 1234 is the user password and 3 is the home arming command. If you have the SMS sending function activated in your phone number in case of arming, you will receive a confirmation message.

Disarming

• To disarm the alarm system, proceed as follows:
• From the remote control: press the key
• Through the control panel: press the key
• By RFID TAG: Move the TAG closer to the RFID area marked on the control panel
• Through the Tuya Smart application: touch the Disarm button. Details on controlling the alarm system through the application can be found on page 5.
• By SMS command. The syntax of the message to be sent to the system: 1234#2, in which 1234 is the user password and 2 is the disarming command. If you have the SMS sending function activated in your phone number in case of arming, you will receive a confirmation message.

Panic alarm

To trigger the alarm manually, proceed as follows:

• From the remote control: press the SOS key
• Through the control panel: press the SOS key
• Through the Tuya Smart app: press the SOS key. Details on controlling the alarm system through the application can be found on page 5

General information about the system

• When an AC 230V power outage occurs, the system will continue to run on the internal battery for several tens of minutes.

• Low battery: When the built-in battery is low, you will receive a notification
  on the control panel screen. Connect the included power cord and move the switch to ON to charge the battery.

• Discharged sensor battery: Each wireless sensor added to the system has an
  internal battery. The system detects the status of the sensor batteries and displays the message “Sensor Low Battery” if the batteries are discharged. Replace the respective sensor batteries.

• Tamper: When a Tamper action has been detected (attempt to manipulate, destroy the control panel), the system generates an alarm.

SMS or voice call notification in case of alarm

When an alarm is triggered or a system problem occurs, an SMS notification
or a voice call will be sent to the phone number that was saved in the system.
After answering the call, you will hear the voice message previously recorded in
the system and you will be vocally notified of the location where the alarm was triggered.

Next, you will hear the message: “Press 1 to arm, press 2 to disarm, press 3 to
monitor, press 4 to speak”. If you have confirmation that it is a false alarm, press 1 to cancel the ongoing alarm.

References

• mypni.eu/products/8045/download/certifications

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>