VEVOR ZLSJSC-3BXGLYSDWKV1 Water Distiller User Manual

VEVOR ZLSJSC-3BXGLYSDWKV1 Water Distiller

If the water has a taste at the beginning of use, it is normal, please kindly use citric acid cleaning agent and hot water for immuring 12 hours, after using 7-8times will be normal.

Read these user instructions carefully before starting to use the equipment.

Recommendations

• Always place the equipment on a level surface and make sure there is adequate ventilation.
• Remove the plug from the power socket when the equipment is not in use – this also applies when filling, emptying and cleaning.
• Never use an electric cable that is damaged.
• Do not immerse either of the two equipment components in water and ensure that the exterior remains dry.
• When distilling has completed, it is recommend- ed to only disconnect the power cables and remove the casing lid after it has cooled for at least 10 minutes.
• This is to prevent burning caused by the steam.
• Never allow children to operate the equipment.
• Do not clean the equipment using steel brushes or abrasives.
• Never pour boiling water into the water bottle.

User instructions

• The equipment consists of two components: the lid with the cooling spiral/cooling fan and the lower casing.
• Remove the lid from the casing and take out the If you want to continue distilling, it is recommended to only disconnect the power cables and remove the lid from the casing after about 10 minutes. Ihis is to prevent burning caused by the steam.
• Next, pour water into the casing and start the whole process over again. It is recommended not to use the first bottle of water bottle. Pour water into the stainless steel casing up to the maximum level line (4 litres),
• The distilling process is quicker when using hot water.
• Put the lid back on the casing and plug the power cable from the lid into the nearest socket.
• Make distilled water from the equipment.
• This may De Contaminated by the manufacturing process or the packaging.
• To distil water, we recommend setting the device to the maximum temperature of 108 °C. For other applications, it is better to use the sure that the lid is properly fitted to the casing.
• Place the water bottle under the outlet of the equipment to collect the distilled water. Now connect the power cable into the casing and plug it into a suitable power socket. Press “ON/OFF”. When the equipment reaches the target Set the desired temperature for distilling. Ihe cooling fan starts rotating and it starts to warm up.
• The first drops of distilled water appear in the water bottle after approximately 30 minutes.
• Remove the cable from the power socket once all the water has been distilled.
• If this is not done, the equipment automatically switches off the heating element after a period of time. standard temperature of 95C. temperature ,the equipment goes into a constant temperature.
• The cooling fan will gap rotation. The equipment has a switching between Celsius and Fahrenheit.
• The equipment has automatic memory temperature.
  Warning: the device can become hot during use..

Cleaning

• Use a normal cleaning detergent for cleaning the exterior of the equipment. Apply it by using a damp cloth and then dry it off.
• Use tap water for rinsing the internal parts of the stainless steel casing. This must be done each time after use. If necessary, add a little citric acid to the water in order to remove any deposits.

FILTER
Inside the stainless steel filter is an activated charcoal sachet. Each sachet will last approximately 3months. To change the sachet remove the steel filter from the unit (this can be done by using a yardsnap’ Replace with a new sachet and replace steel filter to machine.)

Messages:

• “E”: If for any reason the temperature becomes too high, the thermal device will automatically Switch off the heating element.
  “E ” appears on the display. Press “ON/OFF°” button, the display will be switched off. After cooling down, PRESS the “ON/OFF” button, the equipment works at the previous set temperature.

• “H: “H” is displayed and the equipment stops working when the preset temperature is exceeded. Press the reset button to continue distilling.

• “F”: This message indicates that the temperature sensor is defective.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>