iOttie iTap 2 Wireless Air Vent Mount User Manual
- June 8, 2024
- iOttie
Table of Contents
iOttie iTap 2 Wireless Air Vent Mount
Getting Started
For optimal mounting and charging, please follow the detailed instructions within this manual when using the iTap 2 Wireless Charging Mount. iOttie is not liable for possible damages due to product misuse.
Critical Information
-
Placing a Metal Plate
The position of the Metal Plate on the phone is very important for receiving an optimal charge. Please review installation instructions. Inaccurate placement of the metal plate may cause slow charging and overheating. -
Recommended Mounting
For optimal holding, it is recommended to portrait mount your phone.
For thick phone cases or landscape mounting, place the Metal Plate outside of your case to minimize the possibility of slippage. Please review installation instructions. -
Compatibility
Before using product, make sure your device is Qi Wireless compatible. Compatible devices include iPhone X, iPhone Xs, iPhone Xs Max, iPhone XR, Samsung Galaxy Note S9, S9, S9+, and S8. -
Qi Wireless Charging in Vehicle
Use the included iOttie Car Charger and Micro USB Cable. If you do use a third party car charger, use a Qualcomm Quick Charge 2.0 or equivalent adapter to receive a wireless charge (with compatible devices).
At a Glance
Metal Plate Alignment Guide
The Qi Receiver Coil is usually located in the center area of the phone. Check with your phone’s manufacturer for Qi coil location. Below are some examples for commonly used phones.
- We strongly suggest you use the included Placement Guide to place the Metal Plate at the bottom of your smartphone or case for receiving an optimal charge.
-
A. Align the + symbol and the side marker lines with the center of your phone or case, making sure the cut-out for the Metal Plate is at the bottom.
B. Once aligned, remove adhesive strip at the top and stick the Placement Guide to phone. -
A. Lift the Guide from the bottom to stick the Protective Film onto the area where the Metal Plate will be.
B. Put Placement Guide back down, flat against your phone or case -
Place one of the Metal Plates as indicated by the cut-out on the Guide. Save the other Metal Plate as backup.
-
Remove the placement guide. Then, simply position the metal plate on top of the magnetic mount head.
Mount Installation
Please use caution when adjusting the Twist Lock on air vent blade. Do not apply excessive pressure to Twist LOck as this may damage the blades. iOttie is not liable for damages due to product misuse.
- Open Twist Lock and push mount completely onto vent blade.
- Slowly tighten Twist Lock for a secure connection to the air vent.
- Plug Micro USB into the charging mount on back of magnetic mounting head.
- Insert car charger into your vehicle’s power port.
The iTap 2 Wireless Air Vent Mount does not have an on/off switch. Once the device is plugged into the power source it will stay on.
Specifications
Wireless Charger Specifications
INPUT
| 9.0V-1.67A
5.0V-20.A
---|---
CHARGING PORT| MICRO USB
LENGTH| 2.85″
WIDTH| 2.6″
HEIGHT| 3.65″
WEIGHT| 3.8oz
Car Charger Specifications
INPUT | 12V~24V |
---|
OUTPUT
|
5V 3A 9V 2A 12 1.5A DC
Charging Indicator
Solid Green Light
|
Smartphone charging.
---|---
Blinking Red Light
|
Smartphone not charging.
Foreign object detected or overheating of mount or smartphone.
Declaration of Conformity (FCC)
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. You can refer to the following completed FCC warnings. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This devi interferenceopytis
Note
This equipment has been tested and found to comply with the limits fora Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio comnmunications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Operational Warnings
- During the charging process, the transfer of electricity gives off heat. Your device may become warm, but should not become exceedingly hot.
- If the device gets wet, please cease charging immediately. Remove all plugs and dry the product completely. Device is only to be operated in a dry. indoor environment.
- Please be careful of excessive drops, dents, punctures, or deformities on the device. If you are concerned, please unplug the device and contact the manufacturer.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
- Operating this device in a hot environment or in direct sunlight for a long period of time may cause malfunctions. We recommend keeping the product in cooler temperatures.
- Please use included components for an optimal experience. To support Qi wireless charge when using a third party car charger ora USB Power Adapter use a minimum output of both “9.0V-1.67A or 5.0V-2.0A” and at least QC 2.0.
- The product’s signal could possibly interfere with you TPMS (tire pressure monitoring system). If you notice that your TPMS light turns on, please tryy using your mount in different locations to avoid the signals from interfering with each other.
- California Proposition 65 this product contains chemicals known to the state of California to cause cancer and birth defects or other reproductive harm.
Caution
OLD ELECTRICAL APPLIANCES MUST NOT BE DISPOSED OF TOGETHER WITH THE RESIDUAL
WASTE, BUT HAVE TO BE DISPOSED OF SEPARATELY.
If you love your iOttie product, let us know by leaving a review online, or Connect with us on our social platforms.
All iOttie products are backed by a 2 year warranty. I Locate your last
parking location with iOttie’s DriveSmarter app.
www.iottie.com cs@iottie.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>