PacLights FPNN series Flat Panel Led Lights Panels and Troffers Installation Guide

June 9, 2024
PacLights

PacLights logo FPNN series Flat Panel Led Lights Panels and Troffers
Installation GuidePacLights FPNN series Flat Panel Led Lights Panels and
Troffers - fig 15

FPNN series Flat Panel Led Lights Panels and Troffers

INSTALLATION GUIDE FPNN
Series LED Flat Panel
PacLights FPNN series Flat Panel Led Lights Panels and Troffers - fig
1IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
PacLights fi xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNINGS:

  • Make certain power is OFF before installing or maintaining fi xture. No user serviceable parts inside.
  • To prevent wiring damage or abrasion, do not expose wiring to edges of sharp objects.

CAUTION:

  • For proper weatherproof function all gaskets must be seated properly and all screws inserted and tightened fi rmly. Apply weatherproof silicone sealant around the edge of the Back Box and/or Junction Box. This is especially important with an uneven wall surface. Silicone all plugs and unused conduit entries.

PIR/DAYLIGHT SENSOR (OPTIONAL)
All models of FPNN are Bluetooth Network Conrol enabled. Remove the Sensor Cover (Fig. 1). Install the PIR Sensor to the FPNN fi xture by attaching the Connector to the PIR Sensor and press into place on the FPNN fi xture (Fig. 2).PacLights FPNN series Flat Panel Led Lights Panels and Troffers - fig
2

RESET / DECOMMISSION
A FPNN fi xture can be de-commissioned from any Network Zone manually by ‘long pressing’ for 5 seconds the ‘Reset’ Button that is located on the Bluetooth Driver inside the FPNN fi xture Panel. Lift the fi xture Panel Cover (Fig. 3). The ‘Reset’ Button is located at the end of the Bluetooth Driver between the Wire Connectors (Fig. 4).
PacLights FPNN series Flat Panel Led Lights Panels and Troffers - fig
3

WIRING DIAGRAM

Connect the ACL and the ACN from the FPNN Fixture to the conduit with the AC power Supply Cable. Follow the Wiring Diagram provided.
AC POWER SUPPLY
PacLights FPNN series Flat Panel Led Lights Panels and Troffers - fig
4

FPNN MOUNTING ONTO T-GRID

  1. The Mounting Clips (4) are located at the sides of the FPNN fixture (Fig. 4). Use Pliers to bend the Mounting Clips at the appropriate bending points. First bend up at the base, then carefully bend out to 90°at the top of the Clip (Fig. 5) (For safety wear work gloves).
    PacLights FPNN series Flat Panel Led Lights Panels and Troffers - fig
5

  2. Insert the FPNN fi xture onto the T-Grid (Fig. 6). The Mounting Clips will set on top of the T-Grid.
    PacLights FPNN series Flat Panel Led Lights Panels and Troffers - fig
6

OPTIONAL FPNN SUSPENDED MOUNT

Secure Safety Cable to Mounting Clip holes as needed to meet local seismic requirements. Safety Cable and method of attachment to the building provided by contractor according to local building codes. Use a Safety Cable (hanger wire) to tie off appropriately (Screws and hanger wires supplied by others) (Fig. 7).PacLights FPNN series Flat Panel Led Lights Panels and Troffers -
fig 7

OPTIONAL FPNN SURFACE MOUNT

  1. Start off by assembling three of the Channels together. Use Screws to fasten the Angles to the corners of the Channel frame (Fig. 8). PacLights FPNN series Flat Panel Led Lights Panels and Troffers - fig 8
  2. Fasten the three Channels of the Surface Mount to the Ceiling surface. Mounting Bolts/Screws not provided (Fig. 9).
  3. PacLights FPNN series Flat Panel Led Lights Panels and Troffers - fig 9Slide in the FPNN fi xture through the open side of the Surface Mount (Fig. 10). This is when all the wiring installations should be made as well. Refer to the wiring diagram.PacLights FPNN series Flat Panel Led Lights Panels and Troffers - fig 10
  4. Once the FPNN fi xture is properly installed into the Surface Mount, fasten the last two Angles and side Channel with Screws to completely enclose the FPNN fi xture (Fig. 11).

PacLights FPNN series Flat Panel Led Lights Panels and Troffers - fig
11

OPTIONAL DRYWALL RECESSED FLANGE

  1. Start off by assembling the Recessed Flanges together by fastening the Screws to the corners of the Recessed Flanges (Fig. 12).PacLights FPNN series Flat Panel Led Lights Panels and Troffers - fig 12
  2. Notch out the ceiling drywall surface. Insert the preassembled Recessed Flange frame flush to the ceiling leaving the Flanged Side underneath the ceiling. If the drywall ceiling is thin install Cables to support the frame and the FPNN fi xture. Cables are not included with the Recessed Flange frame (Fig. 13).PacLights FPNN series Flat Panel Led Lights Panels and Troffers - fig 13
  3. After the frame is properly installed into the ceiling, one can then mount the FPNN fixture. Carefully mount the FPNN fixture onto the Recessed Flange and adjust any Aircraft Cables if necessary (Fig 14). Please refer to wiring diagram for wire installation.PacLights FPNN series Flat Panel Led Lights Panels and Troffers - fig 14
  4. If the Drywall ceiling is at least 1” thick, then the Recessed Flange Frame can be fastened from the sides. See ‘cut-out’ below (Fig. 15). Mounting screws are not included.  PacLights FPNN series Flat Panel Led Lights Panels and Troffers - fig 15

Need help?
(800) 988 -6386
Email: CS@PacLights.com
Website: www.PacLights.com
nstructions and specifi cations are subject to change at any time without notice.
Copyright© 2022 PacLights All Rights Reserved

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals