PacLights FSWC Series LED Wrap Light Installation Guide
- August 21, 2024
- PacLights
Table of Contents
PacLights FSWC Series LED Wrap Light
Product Information
Specifications:
- Product Name: FSWC LED Wrap Light
- Mounting Options: Surface Mount, Aircraft Cable Mount (optional)
- Wattage and Color Selectable
- Input Voltage: AC
Product Usage Instructions
Preparation:
- Unpack the fixture and check for any damage.
- Detach the lens and wiring cover from the fixture.
Wiring:
Before wiring, verify the voltage of the AC supply. If not using dimming
function, cap the 0/1-10V dimming wires. Follow the wiring diagram provided.
Mounting Options:
Surface Mount:
- Use the provided mounting holes on each end of the fixture housing.
- Connect the fixture to the main power source using UL-approved wire connectors.
- Install the lens by hanging from end plate pins and rotating into position.
Aircraft Cable Mount (optional):
- Affix aircraft cables to the building’s structure.
- Route and affix evenly measured aircraft cables to the openings on the back of the fixture.
- Connect the fixture to the main power source using UL-approved wire connectors and conduit.
- Install the lens by hanging from end plate pins and rotating into position.
FAQ:
-
Q: How do I adjust the wattage and color of the FSWC LED Wrap Light?
A: Use the dip switches located on or near the LED driver to select the desired wattage and color (CCT). -
Q: What should I do if I encounter damaged parts during unpacking?
A: Contact customer support at 800-988-6386 or email CS@PacLights.com for assistance.
SAFETY PRECAUTIONS
- To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards, read all warnings and instructions included with and on the fixture box and all fixture labels.
- Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
- Commercial installation, service and maintenance of luminaires should be performed by a qualified licensed electrician.
- For the installation: If you are unsure about the installation or maintenance of the luminaires, consult a qualified licensed electrician and check your local electrical code.
- To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
- Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
INSTALLATION NOTE
- Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply.
- Turn off the power when you perform any maintenance.
- Verify that supply voltage is correct by comparing it with the luminaire label information.
- All wiring connections should be capped with UL approved wire connectors.
- Verify voltage of AC supply before connect. Separate and cap the 0/1-10V dimming wires, if opt not to utilize the dimming function. (Figure 2)
WARNING
- Avoid direct eye exposure to the light source while it is on.
- Account for small parts and destroy packing material, as these may be hazardous to children.
- Risk of burn. Disconnect power and allow fixture to cool before handing fixture.
PREPARATION
- Unpack the fixture. Examine it for any signs of damage.
- Detach the lens and wiring cover from the fixture. (Figure 1)
SELECT WATTAGE and/or COLOR
All models are wattage and color (CCT) selectable, adjust with the dip
switches on or near the LED driver.
WIRING
Verify voltage of AC supply before connect. Separate and cap the 0/1-10V dimming wires, if opt not to utilize the dimming function. (Figure 2)
MOUNTING OPTIONS
Surface Mount
- Use the provided mounting holes on each end of the fixture housing, mount per required application using appropriate hardware (not included). (Figure 3).
- For electrical connections, use UL-approved wire connectors, as mandated by local codes, to connect the fixture to the main power source, following the diagram provided. (Figure 4)
- Install the lens by hanging from end plate pins of the luminaire and rotate into position. Flex the lens to engage end plate pins on opposite side of the luminaire. (Figure 5)
Aircraft Cable Mount (optional)
- Affix the aircraft cables to the building’s structure such as beam or ceiling with appropriate hardware (not supplied). Ensure the chosen hardware is appropriate for your mounting surface.
- To hang the Housing, route and affix each evenly measured aircraft cable to the opennings on the back of the fixture. (Figure 6)
- When making electrical connections, employ UL-approved wire connectors and conduit, adhering to local codes, to connect the fixture to the main power source. (Figure 7)
- Install the lens by hanging from end plate pins of the luminaire and rotate into position. Flex the lens to engage end plate pins on opposite side of the luminaire. (Figure 5)
Need help?
(800) 988 -6386
Email: CS@PacLights.com
Website: www.PacLights.com
Instructions and specifications are subject to change at any time without
notice.
Copyright© 2024 PacLights All Rights Reserved
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>