Paclights RKTN-22D30 RKTN Series LED Troffer Retrofit Installation Guide

: June 9, 2024
: PacLights

Table of Contents

Paclights RKTN-22D30 RKTN Series LED Troffer Retrofit
INSTALLATION GUIDE
PIR/DAYLIGHT SENSOR
RESET / DECOMMISSION
WIRING DIAGRAM
RKTN MOUNTING ONTO A T-GRID
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Paclights RKTN-22D30 RKTN Series LED Troffer Retrofit

INSTALLATION GUIDE

RKTN Series LED Troff er Retroﬁt

IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
PacLights ﬁ xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

WARNINGS:

Make certain power is OFF before installing or maintaining ﬁ xture. No user serviceable parts inside.
To prevent wiring damage or abrasion, do not expose wiring to edges of sharp objects.

CAUTION:

For proper weatherproof function all gaskets must be seated properly and all screws inserted and tightened ﬁ rmly. Apply weatherproof silicone sealant around the edge of the Back Box and/or Junction Box. This is especially important with an uneven wall surface. Silicone all plugs and unused conduit entries.

PIR/DAYLIGHT SENSOR

(OPTIONAL)
The RKTN Series are Bluetooth Network Control enabled. Remove the Sensor Cover (Fig. 1). Install the PIR Sensor to the RKTN ﬁ xture by attaching the Connector to the PIR Sensor and press into place on the RKTN ﬁ xture (Fig. 2).

RESET / DECOMMISSION

A RKTN ﬁ xture can be de-commissioned from any Network Zone manually by ‘long pressing’ for 5 seconds the ‘Reset’ Button that is located on the Bluetooth Driver on top of the RKTN ﬁ xture Panel (Fig. 3). The ‘Reset’ Button is located at the end of the Bluetooth Driver between the Wire Connectors (Fig. 4).

WIRING DIAGRAM

Connect the ACL and the ACN from the RKTN Fixture to the conduit with the AC power Supply Cable. Follow the Wiring Diagram provided. Paclights-RKTN-22D30
-RKTN-Series-LED-Troffer-Retrofit-FIG-4

RKTN MOUNTING ONTO A T-GRID

Prior to installation, shut off the power to the existing ﬁ xture. Remove components from the hosting ﬁ xture that includes the host ﬁ xture lamp(s), ballast cover, ballast, brackets, lamp holders and wiring. Leave supply and grounding leads (Fig. 5).
Lift and install the LED panel End Brackets to each end of the existing Housing (Fig. 6). Fasten the End Brackets with Screws to the Housing (Fig. 7).
If a gap between the ﬁ xture and T-Grid is too large, then the Side Bracket can be installed (Fig. 8). Insert each Tab End into each of the Slots of the End Brackets (Fig. 9).
Align the RKTN ﬁ xture Hinges into the Keyholes/Slots of the End Brackets (Fig 10). Insert and slide into place along the Keyhole/Slot (Fig 11).
Hook the Safety Cables into the existing Housing. Attach the Power Supply Wires (Fig. 12). Please refer to the wiring diagram.
Rotate the RKTN ﬁ xture on its Hinge up towards the End Brackets 6 and T-Grid (Fig. 13).
Rotate both Locking Latches upwards into the slots of the End 7 Brackets (Fig. 14 & 15).