PacLights FSLN Series LED Strip Light Installation Guide

INSTALLATION GUIDE
FSLN Series LED Strip Light

FSLN Series LED Strip Light

IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
PacLights fi xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNINGS:

• Make certain power is OFF before installing or maintaining fi xture. No user serviceable parts inside.
• To prevent wiring damage or abrasion, do not expose wiring to edges of sharp objects.

CAUTION:

• For proper weatherproof function all gaskets must be seated properly and all screws inserted and tightened fi rmly. Apply weatherproof silicone sealant around the edge of the Back Box and/or Junction Box. This is especially important with an uneven wall surface. Silicone all plugs and unused conduit entries.

PIR/DAYLIGHT SENSOR (OPTIONAL)

All models of FSLN are Bluetooth Network Conrol enabled. Remove the Sensor Cover (Fig. 1). Install the PIR Sensor to the FSLN fi xture by attaching the Connector to the PIR Sensor and press into place onto the FSLN fi xture (Fig. 2).

RESET/DECOMMISSION

A FSLN fi xture can be de-commissioned from any Network Zone manually by ‘long pressing’ for 5 seconds the ‘Reset’ Button that is located on the Bluetooth Driver inside the FSLN fi xture. While holding at Slot Insets on the Lens Assembly, lift and tilt the Lens Assembly away from the Housing (Fig. 3). The Safety Cables will hold the Lens Assembly. The ‘Reset’ Button is located at the end of the Bluetooth Driver between the Wire Connectors (Fig. 4).

WIRING DIAGRAM
Connect the ACL and the ACN from the FSLN Fixture to the conduit with the AC power Supply Cable. Follow the Wiring Diagram provided.
AC POWER SUPPLY

FSLN SURFACE MOUNT

1. The Surface Mount Kit is included the FSLN fi xture. The Surface Mount Kit consists of the Junction Box Cover Plates, Screws, Washers and plastic twist resistant Anchors. Install the Junction Box Cover Plates to the FSLN Housing by inserting the screws (Fig. 5 & 6).

2. Remove the Lens Assembly (Refer to Fig. 3) from the Housing and install the FSLN fi xture fl ush to the ceiling with the plastic twist resistant Anchors, Screws, and Washers (Fig. 7).

OPTIONAL FSLN V-HOOK & CHAINS MOUNT

1. The V-Hook Mounting Kit for the FSLN fi xture consists of the Hook and Chain (Fig. 8).

2. Install the Hook and Chain Mounting Kit to the ceiling Joist/Beam.
   Lift the FSLN fi xture and attach to the Hooks (Fig. 9).
   

3. Place the Hooks into the slots and holes at the end of the FSLN fixture Housing (Fig. 10).
   

OPTIONAL FSLN CABLE MOUNT

1. The AirCraft Cable Mounting Kit for the FSLN fi xture consists of the cable and attachments (Fig. 11).
   

2. Install the Cable Mounting Kit to the ceiling joist/beam. Lift the FSLN fi xture to the Mounting Cables and hook into place (Fig.12).
   

3. Place the Hooks on one side of FSLN fi xture fi rst, then place the hooks into other side of FSLN fi xture (Fig. 13). The length of the Cables can be adjusted at the Link by depressing the spring loaded Plunger.
   

PL_INST_FSLN_v0
Need help? (800) 988 -6386
Email: CS@PacLights.com
Website: www.PacLights.com
Instructions and specifi cations are subject to change at any time without notice.
Copyright© 2022 PacLights All Rights Reserved

References

• PacLights- Commercial & Industrial Indoor, Outdoor Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>