PacLights FLHE Series LED Linear High Bay Installation Guide

June 9, 2024
PacLights

FLHE Series LED Linear High Bay
Installation Guide
PacLights FLHE Series LED Linear High
Bay

FLHE Series LED Linear High Bay

IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
PacLights fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNINGS:

  • Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.
  • To prevent wiring damage or abrasion, do not expose wiring to edges of sharp objects.

CAUTION:

  • For proper weatherproof function all gaskets must be seated properly and all screws inserted and tightened firmly. Apply weatherproof silicone sealant around the edge of the Back Box and/or Junction Box. This is especially important with an uneven wall surface. Silicone all plugs and unused conduit entries.

FIELD ADJUSTABLE CCT (Correlated Color Temperature)

Each FLHE fixture has a CCT Switch. The Tunable CCT Switch is a device that allows the user to choose a desired color temperature 4000K and 5000K (Fig. 1).

PacLights FLHE Series LED Linear High Bay - Figure 1

FLHE CHAIN & V-HOOK MOUNT KIT
Install the FLHE V-Hook into the Mounting Holes of the FLHE fixture (Fig. 2). Wrap two pieces of Chain around the Ceiling Beam and extend the Chain down to the required mounting height. Attach the Chain and Chain Latch to the V-Hook (Fig. 3).

PacLights FLHE Series LED Linear High Bay - Figure 2

WIRING DIAGRAM
Connect the ACL and the ACN from the FLHE Fixture to the conduit with the AC power Supply Cable. Follow the Wiring Diagram provided.
AC POWER SUPPLY

PacLights FLHE Series LED Linear High Bay - POWER
SUPPLY

OPTIONAL FLHE CABLE MOUNT KIT

  1. The Cable Mount Kit includes Aircraft Cables (2). Wrap the two pieces of Cable around the Ceiling Beam and extend down to the required mounting height (Fig. 4).PacLights FLHE Series LED Linear High Bay - Cable Mount Kit
  2. Using the Aircraft Cable (Fixed Cable with tabs on both ends), insert the tabs into the FLHE fixture holes on both sides (Fig. 5) . Once the Tabs have been inserted, the FLHE fixture will be safely secured for mounting (Fig. 6).PacLights FLHE Series LED Linear High Bay - Aircraft Cable
  3. The mounting height of the FLHE fixture is adjusted at the Cable Adjuster. This can be done by pushing in the Button on the Cable Adjuster to release the Adjustable Cable and then pulling the Short End Cable from the side of the Cable Adjuster to set the length of the Adjustable Cable that is suspended from the ceiling. Remove the Set Screw on the Cable Adjuster using an Allen wrench, insert the Fixed Cable inside the two slotted sides and fasten the Set Screw. This is to union the two Cables together (Fig. 7).PacLights FLHE Series LED Linear High Bay - mounting height

OPTIONAL FLHE SURFACE MOUNT KIT

  1. Install the Surface Mount to the Mounting Surface with the Mounting Screws (not included) (Fig. 8). The following figure is a detail of the Mounting Hole on the Surface Mount (Fig. 9).PacLights FLHE Series LED Linear High Bay - Surface Mount
  2. Once the Surface Mounts are installed onto the ceiling/surface and properly secured, place fasteners through the holes on each side of the FLHE Driver Box (Fig. 10). Fasten the Bolt, Lock-Washer and Washer to the FLHE fixture.PacLights FLHE Series LED Linear High Bay - properly secured
  3. After the FLHE fixture is properly secured into place, refer to the Wiring Diagram to install the fixture to an AC Power Supply. All connections must be made inside a J-Box (not included) (Fig. 11).PacLights FLHE Series LED Linear High Bay - FLHE fi xture
  4. This is how the properly surface mounted FLHE Fixture should look (Fig. 12).PacLights FLHE Series LED Linear High Bay - Fixture should look

OPTIONAL FLHE PENDANT MOUNT KIT

  1. Fasten the Pendant Mount to the top-center of the FLHE fixture using the Bolts, Washers, and Lock Washers to screw the Pendant Mount into place (Fig. 13).PacLights FLHE Series LED Linear High Bay - Fasten the Pendant
  2. Once the Pendant Mount is installed onto the fixture, fasten a Conduit to the Mount from the hole on the top side using a Lock Nut that matches the thread on the Conduit. Run the AC Power Supply Cable down the Conduit and join the wires to the FLHE Driver (Fig. 14). The small FLHE Wire Panel can be removed by removing one screw if necessary (Fig. 15).PacLights FLHE Series LED Linear High Bay - Pendant Mount
  3. Once all wiring is complete, use the two Cover Plates that are provided to cover the sides of the Pendant Mount (Fig. 16). Use the Screws to fasten the Cover Plates into place (Fig. 17).PacLights FLHE Series LED Linear High Bay - Cover Plates

OPTIONAL FLHE WIRE GUARD KIT

  1. The Wire Guards are in various sizes for the corresponding FLHE fixture chosen (Fig. 18).PacLights FLHE Series LED Linear High Bay - Wire Guards
  2. Use the (four) formed Clips to fasten the Wire Guard onto the FLHE fixture. This is done by using the (four) holes located on the ends of the fixture (Fig. 19).PacLights FLHE Series LED Linear High Bay - formed Clips
  3. The FLHE fixture is now ready to be safely mounted onto various types of mounting methods and ready for wiring installation (Fig. 20).PacLights FLHE Series LED Linear High Bay - safely mounted

OPTIONAL LIGHTING CONTROLS

  1. The FLHE fixtures have Optional Lighting Control Sensors that can be added. Unscrew and remove the plastic Sensor Cap from the bottom of the fixture (Fig. 21).PacLights FLHE Series LED Linear High Bay - Lighting Control Sensors
  2. Each Lighting Control Sensor has a ‘Plug and Play’ Connector that inserts into the bottom of the FLHE fixture (Fig. 22).PacLights FLHE Series LED Linear High Bay - LIGHTING CONTROL
  3. Carefully screw in a Lighting Control Sensor into the FLHE fixture (Fig. 23).PacLights FLHE Series LED Linear High Bay - Carefully screw

Need help?
(800) 988 -6386
Email: CS@PacLights.com
Website: www.PacLights.com
Instructions and specifications are subject to change at any time without notice.
Copyright© 2023 PacLights All Rights Reserved

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals