PacLights FCPC Series LED Canopy Light Installation Guide

: June 6, 2024
: PacLights

Table of Contents

FCPC SURFACE/CEILING MOUNT
WIRING DIAGRAM
FCPC RETROFIT 2’ x 2’ CANOPY KIT
FCPC 3/4” NPT PENDANT MOUNT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

INSTALLATION GUIDE
FCPC Series LED Canopy Light

FCPC 095/120/150

IMPORTANT

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
PacLights ﬁxtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

WARNINGS:

Make certain power is OFF before installing or maintaining ﬁ fixture. No user-serviceable parts inside.
To prevent wiring damage or abrasion, do not expose wiring to edges of sharp objects.

CAUTION:

For proper weatherproof function, all gaskets must be seated properly and all screws inserted and tightened ﬁ rmly. Apply weatherproof silicone sealant around the edge of the BackBox and/or Junction Box. This is especially important with an uneven wall surface. Silicone all plugs and unused conduit entries.

FCPC SURFACE/CEILING MOUNT

The FCPC ﬁ fixture can be mounted directly to a Surface/Ceiling. Install the Safety Lanyard with a Screw near the base of the FCPC (Fig. 1). Drill the hole pattern into the Surface/Ceiling to be mounted (Fig. 2). Attached the Lanyard to the Surface/Ceiling. Properly attached the wiring. Fasten the FCPC ﬁ texture to the Surface/Ceiling (Fig. 3).

WIRING DIAGRAM

Connect the ACL and the ACN from the FCPC Fixture to the conduit with the AC power Supply Cable. Follow the Wiring Diagram provided.

AC POWER SUPPLY

FCPC RETROFIT 2’ x 2’ CANOPY KIT

The Retroﬁ t 2’ x 2’ Kit is available for all FCPC ﬁ xtures and includes the Retroﬁ t Plate, Safety Catch, Support Tabs, and fasteners (Fig. 4). The original housing of the ﬁ texture can be used. Power off and detach all related wiring. Remove the old luminaire, lens, reﬂ sector, and ballast prior to installation.
Fasten the FCPC ﬁxture to the Retroﬁ t Plate with Cap Screws, Washers, Lock Washers, and Nuts (4). Fasten the Safety Lanyard with a Screw and Nut to the Retroﬁ t Plate and a Screw (Screw to ﬁxture included with ﬁxture) to the FCPC ﬁxture (Fig. 5).
Attach the Power Supply Cable wires to the FCPC ﬁxture Cable wires. Insert FCPC ﬁxture with Retroﬁ t Plate Hinge End onto Housing Flange and rotate up into place (Fig. 6). Rotate the Support Tabs to rest on the Housing Flange on the opposite side and tighten the Support Tab Screws until Support Tabs pull the Retroﬁ t Plate tight against the Housing.
For larger Canopy Housings, Flange Adapter Brackets (Two Short and Two Long) are provided. Install the Brackets onto the Housing Flanges with a rubber mallet (Fig. 7). If the Canopy Housing is 21 3/4” Square use One Short Flange Bracket and One Long Flange Bracket to form a right angle at one corner of the Housing. If the Canopy Housing is 23” Square use Two Short Flange Brackets opposite to each other and Two Long Flange Brackets opposite to each other. Note: For the Long Flange Brackets, with pliers, the tab ends can be snapped off at the slots (Fig. 8).

FCPC 3/4” NPT PENDANT MOUNT

The Pendant Mount is available for all FCPC ﬁ xtures. Properly attach the wiring based on the Wiring Diagram (Fig. 9).
The FCPC ﬁ xture can now be screwed into the 3/4” NPT Conduit (Fig. 10).

Need help? (800) 988 -6386 Email: CS@PacLights.com Website: www.PacLights.com
Instructions and speciﬁ cations are subject to change at any time without notice. Copyright© 2021 PacLights All Rights Reserved