MONACOR EDL-530EN/SW High-Quality PA Pendant Speaker Instruction Manual

MONACOR EDL-530EN SW High-Quality PA Pendant Speaker

PA Pendant Speaker
These instructions are intended for installers with specific knowledge of 100 V technol-ogy for PA applications. Please read the in-structions carefully prior to installation and keep them for later reference.

Applications

This speaker with EN 54-24 certification is ap-proved for use in voice alarm systems. It is equipped with a transformer for operation in 70 V and 100 V systems, but it can also be directly connected to a low-impedance ampli-fier output. The connected load is adjusted via a rotary switch. The 2-way coaxial system used ensures excellent sound quality for speech and music.

Important Notes

The product corresponds to all relevant directives of the EU and is therefore marked with . The product corresponds to the relevant UK leg-islation and is therefore marked with UKCA.

• The product is suitable for indoor use only. Protect it against dripping water, splash water and high air humidity. The admissible ambient temperature range is 0 – 40 °C.
• For cleaning the product, only use a dry, soft cloth; never use water or chemicals.
• No guarantee claims for the product and no liability for any resulting personal damage or material damage will be accepted if the prod-uct is not correctly used, not correctly installed or not expertly repaired.

If the product is to be put out of operation definitively, dispose of the product in accordance with local regulations.

Installation

WARNING During operation, there is a hazard of contact with a dangerous voltage of up to 100 V at the con-nection cable. Installation must always be carried out by skilled personnel.
Observe the load of the speakers on the PA amplifier. Overload may damage the amplifier! The total power of all speakers connected must not exceed the amplifier power.
The following parts are supplied with the speaker:

• 5 m steel wire rope and eyebolt for fastening the rope to the speaker housing
• self-locking wire rope clamp, the rope is passed through the clamp to create a loop for suspension

1. Before installing the speaker, switch off the PA amplifier so that the speaker cable will not carry any voltage!

2. Remove the housing cover. Use the rotary switch (1) to set the desired rated load (volume) or, for operation at a low-impedance amplifier output, set the switch to the position “8 Ω” (d). For operation in a 100 V sys-tem, use the outer scale (a); for operation in a 70 V system, use the inner scale (b).
   Attention!

   • In the position “8 Ω” (d), never operate the speaker in a 70 V or 100 V system. The speaker and possibly also the amplifier will be damaged.
   • In a 100 V system, the switch must not be set to the position “–” (c). The speaker may be damaged. This position is only intended for a power rating of 30 W in a 70 V system.

3. Guide the speaker cable through the housing cover (oval hole) and connect it to the green terminal block (2). For connection, disconnect the terminal block from its connector and then reconnect it. When connecting several speakers, make sure that all speakers have the same polarity.

4. Place the housing cover on the speaker and fasten it using the eyebolt for the wire rope.

5. Pass the free end of the rope through the wire rope clamp to create a loop. This loop will allow the speaker to be suspended expertly and securely from a suitable spot.

Specifications

• Certification: . . . . . . . . according to EN 54-24
• Number: . . . . . . . . . I / ISETC. 000520190419
• Power rating
  • 100 V operation: . . . 30 / 15 / 7.5 / 3.8 W
  • 70 V operation: . . . . 30 / 15 / 7.5 / 3.8 / 1.9 W
  • 8 Ω operation: . . . . . 30 W
• Frequency range: . . . . 65 – 20 000 Hz
• Sensitivity: . . . . . . . . . . 90 dB (1 W / 1 m)
• Speakers
  • Bass speaker: . . . . . . 13.33 cm (5.25”)
  • Tweeter: . . . . . . . . . . 25 mm (1”)
• Housing material: . . . . ABS
• Ambient temperature: 0 – 40 °C
• Dimensions: . . . . . . . . 195 mm × 250 mm
• Weight . . . . . . . . . . . . 2.26 kg

View from above without housing cover

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>