FELIBO Desktops 48″ and Larger Instruction Manual

FELIBO Desktops 48″ and Larger Instruction Manual

Caution

• Keep children and pets away from the electric height-adjustable desk during the operation. Unplug the power cord during a thunderstorm or if you do not intend to use the desk for a long time.
• Make sure desktop not touching the wall.
• Ensure no obstacles in the desk’s path and no object above and 20″ under the desk.
• Working environment temperature 0-40°C, keep products away from corrosive gas, liquid and dusty objects.
• It is strictly forbidden to disassemble the products privately to avoid that the failure of the products or the damage to the human body caused by electronic products, etc.
• Although the product with anti-collision function, in order to avoid any pinching,
• please ensures that hands or other parts of your body are in a safe position during the operation. Anti-collision is not enabled during all resets. using the high-adjustable read the following instructions carefully before start adjustable desk. The company does not bear any warranty or liability for damage and human injury caused by any abnormal operation.
• It is necessary to reset manually after the initial installation or power off.

Product Overview

BOM

• **Assembling Time

**

• **Two people

**

• Tools
  
  

NO| Part name| Qty (PCS)| NO| Part name| Qty (PCS)
---|---|---|---|---|---
1| Foot| 2| 10| Extension Tube| 2
2| Column| 2| 11| Connection Strap| 7
3| Side Bracket| 2| 12| Keyboard Tray| 1
4| Right Tube| 2| 13| Separation Blade| 2
5| Left Tube| 2| 14| Slide Rail| 2
6| Table Board| 4| 15| Power Cord| 1
7| Control Box| 1| 16| Power| 1
8| Hanger| 2| 17| Extension Cable| 1
9| Hanging Brecket| 3| | |

Installation Instruction

STEP 1:

• Set the right tube and left tube flat
• Insert the extension tube to the right tube and left tube as is shown in the picture, pre-tighting the screws. Right Tube
  
  When the connecting rod is stretched to the position of the hole, it can no longer be stretched.

STEP 2

• Find a table about 1.2meters long and place the frame along the edge of the table Insert the columns into the place which is between the left and right tubes respectively, line up the holes on the frame and column.
• Pre-tighten the screws.
  
  Avoid excessive tightening screws

STEP 3

• Mounting the side bracket on the each side of column.
• Fasten the screws.
  
  Avoid excessive tightening screws

STEP 4

• Line up the screw holes on the feet and columns.
• Fasten the screws.
  
  Avoid excessive tightening screws

STEP 5

• Place the table plate as shown, insert the wooden pin into the hole, then splice it together, as close as possible, fasten the connecting piece to the table plate with tapping screw.
  
  
  

Step 6

• Install the keyboard holder as shown
  
  
  
  

• Place the frame on the table plate and stretch to the appropriate position so that the hole on the frame is aligned with the lead hole of the table plate, the hook is placed on both sides, and the screws are fastened. Align the power hanger.

• Keyboard holder, control box mounting hole with the lead hole of the table board and fasten the screw. Pay attention to the power hanger according to the pre-folding line bending, keyboard support fastening need to pull the guide rail.

• As shown below, connect related parts, including control box, extension cable and power cord.
  
  
  The frame width is adjustable: 42 inch-59 inch, which is suitable for different desktop.
  

STEP 7

• Tidy up all the power cables, and fasten with cable clip.
• Turn the desk board over and turn it on.
  

Instruction

• Manual Reset
  It is necessary to be reset manually after W the initial installation and power off.

  • Keep pressing down key till the desktop till display shows “E-1” and “rES” alternately and release the key.
  • Keep pressing down key, the desktop will move slowly down and return back till the display shows 27.6″.
  • Release the key , the height-adjustable desk resetting finished. C)
      Note: The anti-Collision function is not enabled during all resets. Please note that there is a potential risk of pinching in this case, and be sure no obstacles in the desk’s path.

• Up and Down

  • Keep pressing “up” key till the required height is reached.
  • Keeping pressing “down” key till the required height is reached.

• Saving position
  Press the memory key until the columns have reached the desired memory position.

  • Adjust the desktop to the height you want to save
  • Press “S” key , till the display will show “S -2
  • Press “1” , and the display will show alternately as “S-1” and the desktop height.
  • Press “S” key, the first memory position is set successfully .Similar progress for 2 and 3 memory positions.

• Anti-Collision function
  Before use, please make sure removing obstacle in 0 advance and human body is in the safe position.

  • Once the desktop encounters any obstacle in its path, the screen displays
  • The desktop will move a defined distance in opposite direction, and it would be used normally after removing the obstacle.

• Container and self-stop positions.
  Do not enable this function only when you are really need in some situation

  • Keep pressing the key “S” for 3 seconds till the display shows “S–” to enter setup menu.
  • Press up key till the display flash as “HLP”.
  • Press “1”, the display show alternately as “H-P” and current height.
  • Keep pressing up or down key till the required upper limit position is reached.
  • Press “S”, the desktop height will be showed and the shelf stop position has been set.
  • Press “2”, the display will show alternately “L-P” and current height, keep pressing down key till the lower limit position is reached, press S, the container stop position has been set.
    Note: By this function would be used to limit the movement area of desktop, when the container is underneath or any shelf above the desktop. Once it is set, the new upper or lower limitation position will be stored.

• Change the displayed Unit(cm/inch)

  • Keep pressing key “S” till the display show “S–” to enter the setup menu.
  • Press “up” key, the display will show “Unt”.
  • Press “1” , and the display will show alternately as “Unt” and the desktop height unit by “cm”.
  • Press “S” key to save the unit as cm.
  • Press “2”, and the display will show alternately as “Unit” and the desktop height unit by “inch”, press key “S” to save the unit as inch.

• Amend the desktop height displayed

  • Keep pressing down key till the desktop till display shows “E-1” and “rES” alternately and release the key.
  • Keep pressing key “S” till the display show “Ur” and “OFF” alternately.
  • Keep “Up” or “Dn” several times, till the display show “End” and height.(In this case, the unit is mm or inch when this system’s metric or imperial)
  • Press “1”,”2″ and “3” respectively, and to adjust the first number, the second number and the third number. If you click one, the number will increase by 1, till you get to the value you want.
  • Press “5” the height has been changed to defined digit.
    Note: The function enables you to change the height shows on the display based on the actual measurement.

• Plug detection
  The function can detect whether the motors are collected normally.

• • Once the display shows “E-3” and “rES”, it reminds you check whether any motors fail connected with control unit. Please connect the main cable again, wait at least 5 seconds.
  • Connect all the plugs.
  • Follow manual reset procedure

• Reset to factory setting
  With this function, you can make the control unit 0 to factory setting.

  • Keep pressing “S” till the display shows “FAC”.
  • Press “S”, and the control unit to factory setting (including memory position, container-and shelf-stop position, etc.).

Code meaning and Trouble shooting

Code meaning

for further operation
E-2| Anti-Collision function| It can be used normally after removing the obstacle
dut| Operated continuously without suitable rest| Make the desk rest around 15minutes for further operation

Trouble Shooting

refer to Manual reset
E-3| Check the cables and ensure they are well connected, and the height- adjustable desk can be used normally after manual reset

Technical Data

Technical Data

Why choose FEZIBO?

Many ergonomic office solutions come at high cost. Our mission is to use innovation, creativity, and efficiency to produce a more affordable solution that doesn’t sacrifice quality and is easily accessible to the millions of home and office workers globally.

WARRANTY SERVICE

To provide the best service to you, don’t forget to register your Fezibo product to confirm your warranty. It only takes a few simple steps and then you can access a wide range of services such as technical support, new product alert, promotions, and warranty service from Fezibo.
Send your name and order ID to [email protected]

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>