Laserliner SuperPlane-Laser 3D Pro Cross Line Laser User Manual
- June 9, 2024
- Laserliner
Table of Contents
Laserliner SuperPlane-Laser 3D Pro Cross Line Laser
INTRODUCTION
Completely read through the operating instructions, the „Warranty and Additional Information“ booklet as well as the latest information under the internet link at the end of these instructions. Follow the instructions they contain. This document must be kept in a safe place and if the laser device is passed on, this document must be passed on with it. Three-dimensional laser with horizontal and two vertical 360° laser circles and slope function for aligning tiles, wall studding, windows, doors, etc
General safety instructions
- The device must only be used in accordance with its intended purpose and within the scope of the specifications.
- The measuring tools and accessories are not toys. Keep out of reach of children.
- Modifications or changes to the device are not permitted, this will otherwise invalidate the approval and safety specifications.
- Do not expose the device to mechanical stress, extreme temperatures, moisture or significant vibration.
- The device must no longer be used if one or more of its functions fail or the battery charge is weak.
Safety instructions
Using class 2 lasers
Laser radiation!
Do not stare into the beam! Class 2 laser
< 1 mW · 650 nm
EN 60825-1:2014
- Attention: Do not look into the direct or reflected beam.
- Do not point the laser beam towards persons.
- If a person’s eyes are exposed to class 2 laser radiation, they should shut their eyes and immediately move away from the beam.
- Under no circumstances should optical instruments (magnifying glass, microscope, binoculars) be used to look at the laser beam or reflections.
- Do not use the laser at eye level (1.40…1.90 m)
- Reflective, specular or shiny surfaces must be covered whilst laser devices are in operation.
- In public areas shield off the laser beam with barriers and partitions wherever possible and identify the laser area with warning signs.
Safety instructions
Dealing with electromagnetic radiation
- The measuring device complies with electromagnetic compatibility regulations and limits in accordance with the EMC Directive 2014/30/EU.
- Local operating restrictions – for example, in hospitals, aircraft, petrol stations or in the vicinity of people with pacemakers – may apply. Electronic devices can potentially cause hazards or interference or be subject to hazards or interference.
Automatic alignment of the device with a magnetically dampened pendulum
system. The device is brought into initial position and aligns itself
autonomously.
Transport LOCK: The device is protected with a pendelum lock during
transport.
Devices with PowerBright technology have special high-performance diodes to
produce super bright laser lines. These remain visible over longer distances,
in bright ambient light and on dark surfaces.
Number and direction of the lasers
- H = horizontal laser
- V = vertical laser
- S = slope function
Inserting the batteries
Open the battery compartment (3) and insert the batteries in accordance with
the installation symbols, ensuring the correct polarity.
DESCRIPTION
-
Laser emitting window
-
Slide switch
- ON
- OFF / Slope mode /
-
Transport lock
Battery compartment (bottom) -
1/4” tripod threads (bottom)
-
Laser line selection button / Slope mode on
WARNING
When transporting always switch off all lasers, secure the pendulum and set the slide switch to “OFF”!
Low battery indicator: All laser lines flash for 3 seconds and then go out when the battery charge is low.
Horizontal and vertical levelling
Release the transport restraint, set slide switch (2) to “ON”. The horizontal
laser line appears. The laser lines can be switched individually with the
selection button.
WARNING
The transport restraint must be released for horizontal and vertical levelling. The laser lines flash when the device is outside the automatic levelling range of 3°. Position the device such that it is ! within the levelling range.
Slope mode
Do not release the transport restraint, set slide switch (2) to “OFF” and
switch on slope mode by pressing and holding (3 seconds) button 5. Select the
laser with the selector button (5). Sloping planes and tilts can now be
measured. In this mode, the laser lines no longer align automatically. This is
signalised by the laser lines flashing.
Preparing the calibration check:
It is possible for you to check the calibration of the laser. To do this,
position the device midway between 2 walls, which must be at least 5 metres
apart. Do this by turning the unit on, thus releasing the transport restraint
(cross laser on). Please use a tripod.
-
Mark point A1 on the wall.
-
Turn the device through 180° and mark point A2. You now have a horizontal reference between points A1 and A2.
Performing the calibration check: -
Position the device as near as possible to the wall at the height of point A1.
-
Turn the device through 180° and mark point A3. The difference between points A2 and A3 is the tolerance.
WARNING
When A2 and A3 are more than 0.35 mm / m apart, an adjustment is necessary. ! Contact your authorised dealer or else the UMAREX-LASERLINER Service Department.
Checking the vertical line:
Position the device about 5 m from a wall. Fix a plumb bob with a line of 2.5
m length on the wall, making sure that the bob can swing freely. Switch on the
device and align the vertical laser to the plumb line. The precision is within
the specified tolerance if the deviation between the laser line and the plumb
line is not greater than ± 1.75 mm.
Checking the horizontal line:
Position the device about 5 m from a wall and switch on the cross laser. Mark
point B on the wall. Turn the laser cross approx. 2.5 m to the right and mark
point C. Check whether the horizontal line from point C is level with point B
to within ± 1.75 mm. Repeat the process by turning the laser to the left.
WARNING
Regularly check the adjustment before use, after transport and after extended periods of storage.
Information on maintenance and care
Clean all components with a damp cloth and do not use cleaning agents, scouring agents and solvents. Remove the battery(ies) before storing for longer periods. Store the device in a clean and dry place.
Technical data
Technical data (Subject to technical alterations. 18W10)
Self-levelling range| ± 3°
Precision| ± 0.35 mm / m
Operating range (depending on room illumination)| 15 m
Laser wavelength| 650 nm
Laser class| 2 / < 1 mW
Power supply| 4 x 1.5 V alkaline batteries (type AA) / rechargeable batteries
Operating time with 3 laser levels with 2 laser levels
with 1 laser level
| approx. 6 hours
approx. 10 hours
approx. 25 hours
Operating conditions| 0…50°C, 80%rH, no condensation, max. altitude 4000 m
Storage conditions| -10°C…70°C, 80% rH, no condensation
Weight (incl. batteries)| 650 g
Dimensions (W x H x D)| 85 x 125 x 130 mm
EU directives and disposal
This device complies with all necessary standards for the free movement of
goods within the EU. This product is an electric device and must be collected
separately for disposal according to the European Directive on waste
electrical and electronic equipment.
Further safety and supplementary notices at:
http://laserliner.com/info?an=supplalas3pl
SERVICE
Umarex GmbH & Co. KG
– Laserliner –
Möhnestraße 149, 59755 Arnsberg, Germany
Tel.: +49 2932 638-300, Fax: +49 2932 638-333
info@laserliner.com
Umarex GmbH & Co. KG
Donnerfeld 2
59757 Arnsberg, Germany
Tel.: +49 2932 638-300, Fax: -333
www.laserliner.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>