HIBOY P6 Fat Tire Electric Bike User Manual

: June 9, 2024
: HIBOY

HIBOY P6 Fat Tire Electric Bike

IMPORTANT! BEFORE RIDING, YOU SHOULD

Make sure your electric bike is fully charged before the first ride
Make sure the pedals are tight
Make sure the front wheel is installed properly and tight
Check to be sure the tires are inflated properly
Learn how to use the display
Wear a helmet when riding is highly advised

When riding, please

Always respect pedestrians
Obey local traffic rules
Pay attention to other running vehicles around you

After riding

If there is any abnormality or loose parts, please check and repair as soon as possible
After riding on a rainy day, please clean up the rainwater and sediment immediately

f you have any trouble with the installation, please contact Hiboy customer service for support: ebike@hiboy.com

PACKAGE CONTENTS

| Charger x 1
---|---
| Headlight screw x 1
| Installing tool x 1
| Pedals (R and L) x 2
|
| Battery Key x 2
| Hexagon wrench x 1
| User manual x 1

Please check package contents carefully, if anything is missing or damaged, please contact Hiboy customer service for support: ebike@hiboy.com

PRODUCT OVERVIEW

INSTALLING THE HANDLEBARS

Shown in figure 1, according to the direction of the arrow, rotate the handle stem towards the front of the bike.
Put the handlebar in the handlebar mount and be careful with the wires.
Insert the screws and tighten alternating sides with installing tool.
Verify and check all items are tight.

INSTALLING THE FRONT WHEEL

Insert the front wheel in between the front fork on the bike. Be sure the fork is resting on the outside of the axle.
.Shown in figure 2, align the wheel axle with the disc brake slot, put the brake disc into the disc brake slot. Keep the skewer and spring on the RIGHT side of ebike’s riding direction, and the other spring and the end nut on the LEFT side of ebike’s riding direction. Then insert the skewer into the wheel axle, shown in figure 1. BE AWARE TO DISTINGUISH THE LEFT SIDE AND THE RIGHT SIDE.
Screw the skewer with the end nut and tighten.
Lock up the lever. Lift the lever up until parallel with the front fork. The front wheel is now installed.

INSTALLING THE PEDALS

Identify the Left and Right labels on the pedals. They can only be installed in their own side. INCORRECT INSTALLATION WILL CAUSE DAMAGE. PLEASE BE AWARE TO DISTINGUISH LEFT & RIGHT BEFORE INSTALLATION.
L is for the Left pedal of the riding direction; R is for the Right pedal of the riding direction, the chain side.
Take the wrench which is integrated in the multi-function installing tool and tighten the nuts with wrench.

INSTALLING THE HEADLIGHT

Shown in Figure 1, insert the screw of the headlight into the headlight hole.
Tighten the screw with nut by using the installing tool.
Use a hexagon wrench to lock in a clockwise direction.

INSTALLING THE SADDLE

Install the saddle according to the picture.
Push the saddle down, pull up or push down to adjust the height.
Check to make sure the saddle is fully inserted and adjust it accordingly.
Lock the handle.

DISPLAY INTRODUCTION

HOW TO USE THE DISPLAY, HEADLIGHT & HORN

Press to turn on the display. Your bike will be ON. Press again to turn it off. The display will automatically shut down when there is no operation or riding for 5 minutes.
Short press “+” or “-” button to change the assist level from 0 to 5. 0 is without assist. 5 is the max assist level.
Short press to switch the display data in the multi-function area when riding.
When the ebike is static, long press “-” to enter the 6KM/h cruise mode; release “-” to cancel the cruise mode.

HOW TO TAKE OFF THE BATTERY

Insert the key and turn 90 degrees clockwise.
Take out the battery upwards.

HOW TO CHARGE THE BATTERY

Charge the battery on the bike, find the charge port at the bottom of the battery tube.
Pull out the rubber flap of the charging port and insert the charger output plug into the charging port. Connect the input plug to the power supply. The small light on the charger in RED indicates it is in charging; GREEN indicates it is fully charged.
You can also take off the battery and place it in a clean and flat place in room temperature and charging.

NOTES OF CHARGING

.Fully charging time may vary from 6 to 7 hours.
The small light on the charger in RED indicates it is in charging; GREEN indicates it is fully charged.
Insufficient charging will not influence the battery lifecycle. AVOIDING deep discharge is helpful to protect the battery and extend its lifecycle.
Pay attention to check whether the surface temperature of the battery case rises too high during charging. It is FORBIDDEN to cover battery while charging.
Due to high temperature in summer, it is NOT advised to charge it immediately after riding. In winter, it is FORBIDDEN to charge the battery OUTSIDE where the temperature is below 32-degree F. You are recommended to charge it in room temperature.
If the battery will not be used for a long time, take it off from the bike and discharge its capacity to 60%-80% for stock. Disconnect it from the charger and place it in a dry, ventilated place without direct sunlight. In order to maintain
a long lifecycle, it is recommended to charge the battery every two months.

DAILY CARE AND MAINTENANCE

Cleaning

If you see stains on the bike, wipe them off with a damp cloth. If the stains won’t scrub off, put on some toothpaste and brush them with a toothbrush, then wipe them off with a damp cloth.
Do not clean the bike with alcohol, gasoline or any other corrosive and volatile chemicals.
Do not wash the bike with a high-pressure water spray.
Before cleaning, make sure that the bike is turned off, the charging cable is unplugged, and the rubber flap of the charging port is closed.

Battery maintenance

Use original battery packs.
Do not touch the contacts. Do not dismantle or puncture the casing. Keep the contacts away from metal objects to prevent short circuit.
Use original power adapter to avoid potential damage.
After each use, fully charge the battery to prolong its life span.

Storage

When the bike is not in use, keep it indoors where is dry and cool with temperature between 32°F / 0°C and 113°F / 45°C.
Excessive sunlight, overheating or overcooling may be harmful to battery’s life span.

TROUBLE SHOOTING

Symptoms	Possible Reason	Solutions
1	Ebike doesn’ t work	1.1nsufficient battery power

SPECIFICATIONS

ITEM	SPECIFICATIONS

Model

|

P6

LIMITED WARRANTY STATEMENT

30 DAY SATISFACTION GUARANTEED RETURN POLICY

If you are unsatisfied with your purchase, Hiboy’s return policy allows you to return the product purchased on the Au0thorization channel within 30 days counting from the date of receipt of shipment and request a refund from the Authorization channel for any reason.
Note: Express shipping cost is non-refundable.
For the return request, Hiboy is not responsible for lost packages due to the carrier, or products received that cannot be verified. Received products that have damaged determined to have been caused by the end-user may be subject to denial of the return request.

LIMITED PRODUCT WARRANTY

Hiboy warrants the original purchaser that your Hiboy product shall be free from defects in materials and workmanshipunder normal use for a period aforementioned.
Hobby does not warrant the operation of the product will be uninterrupted or error-free.
Hobby is not responsible for damage arising from failure to follow instructions relating to the product’s usage.

CONTACT US

Contact us if you experience issues relating to riding, maintenance and safety, or errors/faults with your Hiboy Ebike P6. Lockwood Group Inc
4045 Cheyenne Ct Chino CA 91710
E-mail Service: ebike@hiboy.com