DYNOJET PV3-25-09 Can Am Defender Installation Guide

DYNOJET PV3-25-09 Can Am Defender Installation Guide

INTRODUCTION

POWER VISION OVERVIEW—FRONT VIEW

POWER VISION OVERVIEW—SIDE VIEW

Thank you for purchasing the Power Vision from Dynojet Research. At Dynojet, our mission is to make every ride the ultimate ride. The Power Vision allows you to tune your stock ECU to achieve optimal performance from your vehicle.
The Power Vision is the device to interface between your computer and the vehicle ECU. Use the buttons to navigate the device menus, make selections, cycle through the four full-color available gauge screens, and log data. Connect to the diagnostic port to fl ash a tune; use the USB connection to interface between the Power Vision and your computer.
Make your Power Vision device yours; display the channels you want to see with four user-customizable full-color gauge screens. Make the Power Vision your window into your vehicle; secure the Power Vision to your dashboard or handlebars to monitor any desired set of gauges such as Throttle Position, Engine Speed, and more. Wideband Air:Fuel Ratio and integrated belt temperature can be added as channels to the PV3’s monitors by adding the accessories available at
www.dynojet.com.
For state of the art technical support, please visit
www.dynojet.zendesk.com.

INSTALLING THE POWER VISION

1. Secure the Power Vision to the vehicle using the supplied Velcro. Make sure the Power Vision will not interfere with the operation and steering of the vehicle. Visit www.dynojet.com for an array of mounting solutions for your Power Vision.
   Note: The Power Vision does not need to be mounted to the vehicle, however, the Power Vision provides a window into your vehicle. Mount the Power Vision to your dashboard and gain access to customizable full-color gauge screens, along with data logging and troubleshooting screens.

2. Attach the diagnostic cable to the diagnostic port on the Power Vision and to the diagnostic port on the vehicle. Defender Models: located under the front hood.

GETTING STARTED

Use the Tune File Wizard to prepare your Power Vision device with the stock (stk) and tune (djt) fi les needed to fl ash your vehicle.

1. Connect the Power Vision to the vehicle.

2. Turn the key on. The Power Vision will scan for fi les. There are three possible fi le states:
   File State 1: No compatible tune or stock fi les.
   File State 2: No compatible tune fi les.
   File State 3: All required fi les found.

3. Gauges are displayed

Connect the Power Vision to the vehicle diagnostic port to collect ECU information. Turn the key on.

File State 1:
Go to tunes.dynojet.com/ to download stock and tune fi les.

File State 2:
Go to tunes.dynojet.com/ to download tune fi les.

File State 3:
All required fi les found. The Power Vision is ready to fl ash a tune to the connected vehicle.

FLASHING YOUR VEHICLE

The Power Vision must be paired to the connected vehicle ECU to function properly.

Note: Once paired to the vehicle ECU, the Power Vision will not work on another vehicle without purchasing a tune license.

1. From the Main Menu, select Flash Tune.

2. Select the tune fi le (.djt) and press Enter to view the Tune Info.
   Note: The Dynojet tune fi le (.djt) is a tune fi le which is different (better than stock performance or the necessary fi le when bolting on an exhaust, for example); the stock fi le (.stk) is the direct duplicate of what the OEM shipped.

3. Press Enter to accept the tune, or restore the ECU to original stock (.stk) fi le, and pair the Power Vision to the vehicle.
   Note: Pair to vehicle will only happen on the fi rst fl ash.

4. Press Enter to pair and lock the Power Vision to the ECU and to begin the fl ash. Do not turn off the key switch or disconnect the Power Vision during the fl ash.

5. After the fl ash is complete, turn the key off and wait 45 seconds before turning the key back on to start.

VIEWING THE VEHICLE INFORMATION

This menu allows you to view the device status (paired/not paired), VIN #, Model ID, ECU serial number, tune compat, and checksum compat.
Select Vehicle Tools>Vehicle Information.

VIEWING THE DIAGNOSTIC CODES

This menu allows you to read and clear diagnostic trouble codes.

1. To read codes, select Vehicle Tools>Diagnostics>Active Codes.
2. To clear codes, select Vehicle Tools>Diagnostics>Clear Codes.

RESTORING THE ECU

This menu allows you to restore the ECU. Use Restore ECU if the device does not complete the fl ash or if your vehicle will not start.
Select Vehicle Tools >Restore ECU.

CONFIGURING GAUGES

Make your Power Vision device yours; display the channels you want to see with four user-customizable full-color gauge screens. Each gauge screen has one, two, or four confit curable channels. Monitor channels such as Wideband, AFR, Boost, and integrated belt temperature sensor. Sample gauges shown here; for a complete list of monitors available, open the tune fi le in Power Core or scroll through the gauges on the device when confi guring or selecting channels for the list of options.

1. From the Main Menu, select Device Tools>Confi gure Gauges.
2. Select a gauge screen and press Enter.
3. Select a channel and press Enter.
4. Select a channel from the list and press Enter.
5. Select the precision or units for that channel and press Enter.
6. Continue setting up the remaining channels as desired.
7. Continue confi guring the remaining gauge screens as desired.

LOGGING DATA

The Power Vision is a powerful logging tool to diagnose running issues. Use the Power Vision to log all vehicle operating data and review the data in the Power Core software. Troubleshoot an issue such as knock, speed/RPM limitation, throttle blade closure and more by keeping the Power Vision mounted to view and record channels.

1. Press the Log button to begin logging. The Power Vision screen will illuminate a bright red banner across the top when logging.
2. Press the Log button again to stop logging.
3. Use the Power Core software to view log fi les.

Snapshot Log: Press and hold the Log button for two seconds to record the previous two minutes of operating time.

DELETING DATA LOGS

This menu allows you to delete data logs.

1. Select Vehicle Tools>Delete Data Log.
2. Select a specifi c log to delete or select Delete AllLogs.
   

VIEWING THE DEVICE INFORMATION

This menu allows you to view the device fi rmware version, serial number, and stock code.
Select Device Tools >Device Information.

REFORMATTING THE DISK

This menu allows you to reformat the disk and erase all data.
Select Device Tools >Reformat Disk.

CHANGING THE SETTINGS

This menu allows you to rotate the screen allowing you to change the orientation of the Power Vision device along with adjusting the screen brightness. Turn the brightness up and make your screen pop! Select Device Tools>Settings>Rotate Screen to fl ip the screen.
Select Device Tools>Settings>Brightness to change the screen brightness.

UPDATING THE DEVICE

This menu allows you to update the device with the latest fi rewire

1. Go to www.dynojet.com.
2. From the top navigation menu, select Support>Downloads.
3. Click Power Vision 3.
4. Click the Firmware drop-down and download the Power Vision
5. Firmware for CanAm.
6. Save the fi le to your device.
7. Select Device Tools>Update Device.

DIAGNOSTIC ENABLE

This menu allows you to create a fi le containing device diagnostic information used by Dynojet Tech Support.

1. From the Main Menu, select Device Tools>Diagnostic Enable. This will turn on diagnostic logging. Logging will continue until the device is restarted.
2. If requested by Dynojet Tech Support, connect your Power Vision to a computer and email the diagnostic fi le to PV3tech@dynojet.com. Diagnostic log fi les are placed in the log fi les directory

USB MODE

This menu allows you to connect your Power Vision to your computer and enables sending and receiving fi les.

1. Connect the Power Vision to your computer using the included USB cable. The Power Vision will automatically enter USB Mode. OR From the Main Menu, select USB Mode.
2. Transfer the desired fi les to your computer or to the Power Vision.

USING THE POWER VISION UPDATE CLIENT

This stand alone application will launch the Update Client allowing you to update your Power Vision with the latest fi rmware, retrieve additional tunes, or restore the Power Vision to the original Dynojet factory setting

1. Connect the Power Vision to your computer using the included USB cable.
2. Navigate to the POWERVISION drive attached to your computer and run the Update.exe fi le.
3. Click Update to load the current fi rmware. If the Update button is grayed out, your Power Vision already has the latest fi rmware.
4. Click Restore to reload all original Dynojet tune and stock fi les.
5. Click Get Tunes to open the Dynojet Tune Finder. Follow the instructions to Upload your PV_Info.txt fi le and retrieve new tunes.
6. Click Manual Firmware Update to navigate to and load a version of fi rmware already saved on your computer.

INSTALLING THE POWER CORE SOFTWARE

Download the Power Core software and take tuning to a whole new level.
Note: Downloading the Power Core software is optional and not necessary to use the Power Vision.

1. Go to www.dynojet.com.
2. From the top navigation menu, select Support>Downloads.
3. Click Power Vision 3.
4. Click the Software drop-down and download the Dynojet Power Core software.
5. Double-click the saved fi le to begin installation. Follow the on-screen prompts. Refer to the Power Core Help for more information.

References

• Customer Login | Dynojet
• Powersports Vehicle Parts | Performance Ignition & Fuel Parts | Dynojet

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>