Youin BK1700 Electric Bike User Manual

YOUIN LUXOR
AN ELECTRIC
FAT BIKE LUXOR
INSIDEUser manual
BK1700

BK1700 Electric Bike

YOUmove
YOUup
YOUdown
YOUfold
YOUtravel
YOUrule
Thanks for choosing our product.
Have fun with this electric bike.

Bike Assembly

Deploy the Product

1. Grab the seat and the handlebar. Rotate the front half of the frame forward around the hinge until the front wheel is in the driving position.
2. Lift the locking lever (picture 1) to fully unfold the frame until you hear a click. Flip the lever forward and close it so the frame is secured.
3. Turn the pedals to their horizontal position (picture 2).
4. Raise the handlebar to its vertical position and close its locking lever (picture 3).
5. Place the handlebar and the saddle at the desired height (picture 4 and 5).

Insert, unlock and remove the battery

1. Insert the key into the keyhole.
2. Turn the key to the OPEN position to unlock the battery, now it can be removed (picture 6).
3. Press the battery into the hole to close it again so you can turn on your e-bike.
4. In order to turn on your e-bike, the internal switch of the battery must be in the ON position (picture 7).

Technical information

Parts diagram

Wiring diagram

Technical information

Technical specifications

Security

Use tips
This electric bicycle is designed to transport a single person in each use. Condition your bicycle if you want to transport luggage and try not to exceed the maximum load for which it was designed (127 kg).
Failure to follow the safety advice, or activities that go beyond its intended use, such as going down steps, performing stunts or making improper repairs, will exempt both the manufacturer and the dealer from all liability.
It is recommended to always wear a helmet. In case of driving at night, make sure to turn on the lights, and if possible, also wear a reflective band or vest.
Remember to clean your bike regularly. To do this, avoid the use of pressurized water, since the electronic components can get wet, which can cause a malfunction and even personal injury.
Carefully clean painted surfaces, plastic parts and electronic components. Never use abrasive products such as seawater, saltpeter, soda, etc.
Before each use
Before each ride, you should check that the brakes are secure and working properly.
The handlebar and seat post must be in the correct position and firmly fixed. The wheels must have enough pressure and all the nuts and bolts must be well tightened.
The battery must have sufficient charge for the use that we are going to give it.
Regular checkups (every 1-2 months)
These controls guarantee the perfect condition of the e-bike and optimal operation.

1. Check that the welds on the frame and fork are in good condition and show no signs of corrosion.
2. Check that the front and rear brakes are attached to the chassis and brake effectively.
3. Check tire pressure and tread depth.
4. Check that the rims are well secured and do not have any loose or broken spokes.
5. Check that the handlebar and the seat post are well inserted and firmly tightened.
6. Check that the cables are sufficiently greased and that they have no obstacles in their path.
7. Check that the battery is charged enough.

Operation

Screen

System on/off
Press and hold for a few seconds to turn on your You-ride Texas. Long press again to turn it off.

Change the information on the screen
Briefly press to change the information on the screen. You can toggle between the following information:
VOL – Voltage / CUR – Amperage / WATT – Wattage
ODO – Accumulated mileage / DST – Trip mileage / TIME – Trip time
PAS level adjustment
Press or to adjust the level of pedal assistance.
Accompaniment mode
If you press and hold the button   for 3 seconds, it will start the motor at a constant speed of 6km/h to carry the bike effortlessly while walking next to it. Pressing the brake will deactivate the accompaniment mode.
Do not use it if we are mounted on it. We recommend not to abuse this assistance, especially on long or very steep slopes.
Front light on/off
Long press for for 3 seconds to turn on the front light. Long press again to turn it off.
Rear light on/off
The rear light is turned on directly from the power button above it. Press several times to switch between the 3 available modes: steady light, flashing light 1 and flashing light 2.
The tail light is powered by 2 batteries, please remove the screws and open the cover to change them when you run out of battery.

Front fork
In the front fork you can lock or unlock the suspension (picture 1) and adjust its pressure (picture 2).

Battery charge
When you finish the trip or the battery is running low, charge it immediately.
Charging methods can be divided into two types: one is to take out the battery and then charge it, the other is to charge the battery directly on the electric bicycle. First connect the charger to the charging port of the battery (without connecting it to the socket) and then to the mains. Connect it to a 220V/50-60Hz power supply.

There is an LED indicator on the power supply. The LED is red when the battery is charging. The LED turns green when the battery is fully charged. Recommended charging time: 5-6 hours.
After charging, please unplug the input plug (from the wall outlet) first, and then unplug the output plug (from the bike). The battery charger must have constant voltage. Fluctuating voltage or fluctuating power supply of any kind can damage the storage cells of the battery.
Checking the battery before using it for the first time
WARNING

• The battery is supplied partially charged. To ensure the full capacity of the battery, please fully charge it before using it for the first time.

Battery care

• Even with proper care, rechargeable batteries don’t last forever. Each time the battery is discharged and subsequently recharged, its relative capacity decreases by a few percent. You can maximize the life of your battery by following the instructions in this guide. The battery should be fully charged immediately upon receipt for the full recommended charging time
• For a full 100% charge, leave the battery on the charger for a full hour after the indicator light on the charger turns green.
• Lithium-ion batteries have no “memory”. Partial charge/discharge cycles will not harm the batteries capacity or performance.
• The nominal output capacity of a battery is measured at 25ºC. Any variation in this temperature will alter the performance of the battery and shorten its expected life. High temperatures especially reduce the overall battery life and operating time.
• Always make sure to turn the bike’s ignition switch to “OFF” after each use. If you leave the power switch in the “ON” position, or your electric bike has not been charged for an extended period of time, the battery may reach a point where it will no longer hold a charge.

Recycling Notice

**** Electrical and electronic equipment and batteries contain materials, components and substances that can be harmful to you and your environment, as long as the waste materials (waste electrical and electronic equipment and batteries) are not managed correctly.
Electrical and electronic equipment and batteries are marked with the crossed out bin, as shown below. This symbol means that old electrical and electronic equipment and batteries should not be thrown away; they must be removed separately.
As the end user, it is necessary for you to deliver the exhausted batteries to the appropriate collection points. In this way, you ensure that the batteries are recycled in accordance with the legislation and do not cause any environmental damage.

IOTECNIA S.L.
C/ Puig dels Tudons, 6
Barberà del Vallès (08210)
Barcelona (SPAIN)

Documents / Resources

| Youin BK1700 Electric Bike [pdf] User Manual
BK1700 Electric Bike, BK1700, Electric Bike, Bike
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>