SUNLITE LED T8 Tube Series LED 8W 2 Foot Instant Start T8 Tube Light Fixtures Instruction Manual
- June 4, 2024
- sunlite
Table of Contents
- Product Features
- Product Applications
- Installation Instructions
- ⚠ Safety Precautions:
- INSTALLATION INSTRUCTIONS
- Instant Start Ballast Wiring Diagram (Correct)
- Instant Start Ballast Wiring Diagram (Wrong)
- Safety Information:
- Maintenance Notes
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
LED T8 Tube Series LED 8W 2 Foot Instant Start T8 Tube Light Fixtures
Product Features
- UL certified
- Plug-n-Play replacement
- Full glass housing: No Aging, Yellowing.Bending.
- Compatible with Instant Start, Program Start and Rapid Start T8 electronic Ballast; Compatible with T8 emergency Ballast and dimmable Ballasts.
Product Applications
Widely used in residential buildings, offices, shopping malls, supermarkets, hospitals, assembly lines, warehouses, etc. for energy saving illumination.
Installation Instructions
Please completely comply with these instructions and notes, to ensure that the product is operated in a safe condition.
⚠ Safety Precautions:
- WARNING: Risk of shock. Disconnect power before installation.
- LED T8 lamp for use only with products described and installed in accordance with product specifications. LED T8 lamp to be operated with fluorescent electronic ballast.
- WARNING: RISK OF FIRE, USE ONLY IN PLACE OF FLUORESCENT LAMPS SPECIFIED ON LABEL. RISK OF ELECTRIC SHOCK. SUITABLE FOR DAMP LOCATIONS.
INSTALLATION INSTRUCTIONS
-
Turn Power OFF
-
Remove lens or diffuser (if applicable)
-
Remove existing fluorescent lamps from the luminaire.
-
Bring LED lamp to luminaire and insert lamp pins into luminaire lamp holders.
-
Rotate LED lamp until lamp locks in place. Ensure that the LED lamp front points away from the back of theluminaire.
Note: install LED TB replacement lamp one for each fluorescent lamp removed.
-
Place lens or diffuser back in place (if applicable}
-
Switch power ON.
Instant Start Ballast Wiring Diagram (Correct)
Two Lamp Ballast Correct Wiring
Three Lamp Ballast Correct Wiring
Four Lamp Ballast Correct Wiring
Instant Start Ballast Wiring Diagram (Wrong)
Two Lamp Ballast Wrong Wiring
Three Lamp Ballast Wrong Wiring
Four Lamp Ballast Wrong Wiring
DO NOT INSTALL THIS LAMP IN A PRE – HEAT LUMINAIRE.
THIS LAMP ONLY OPERA TES ON ELECTRONIC BALLASTS. IF LAMP DOES NOT LIGHT WHEN THE LUMINAIRE IS ENERGIZED, REMOVE LAMP FROM LUMINAIRE AND CONTACT LAMPMANUFACTURER OR QUALIFIED ELECTRICIAN.
CAUTION RISK OF FIRE – IF THE LAMP OR LUMINAIRE EXHIBITS UNDESIRABLE OPERATION (BUZZING, FLICKERING, ETC.), IMMEDIATELY TURN OFF POWER, REMOVE LAMP FROM LUMINAIRE AND CONTACT MANUFACTURER.
Safety Information:
(1) Check the lamp before installation, if there is any damage caused during
transportation, do not install.
(2) Maintenance should be carried out by technical personnel only.
(3) Do not stare at the light source with bare eyes for a long time, or beam
to others’ eyes.
(4) Do not place any objects on the lamp.
(5) Keep the lamp away from flame or high temperature objects.
(6) Only replace with same type of LED tube! Risk of electrical shock!
(7) If the glass lamp tube is broken, the lamp must be disposed of
immediately!
Maintenance Notes
(1) Disconnect lamp from power supply before any maintenance.
(2) Clean luminaire with dry cloth.
(3) Do not clean the lamp with corrosive chemicals.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)this device may not cause harmful interference, and (2)this device must accept any interference: received, including interference that may cause undesired operation.
Sunshine Lighting Company
744 CLINTON BROOKLYN.NY 11231 USA
TEL:718-768-7000
FAX:718-768-0970