Dasaita DAS-X9s 4K Dual Dash Camera User Manual

Dasaita DAS-X9s 4K Dual Dash Camera

Please read this manual carefully before using the product Please keep this instruction manual properly.

To Users

Dear users and friends, thank you for purchasing the high-end wireless WIFI driving recorder product produced by our company. This product is a high-tech intelligent driving recorder based on the smartphone platform. It is mainly used for the safe driving of various types of automobile industry.

Precautions

Before using the recorder, please format the TF card or built-in memory on this device.

1. The driving recorder can only be installed inside the car.
2. Please do not operate this product or use the assisted driving control APP while driving.
3. Avoid using and storing this product at abnormal temperature.
4. Do not use this product in an environment with strong magnetic field or severe vibration.
5. Only the officially configured power cords are used, and the use of non-standard power cords may cause unforeseen problems.

Disclaimers

We hereby remind users to read carefully before using this system and fully understand the terms in this statement. If you use this system, you will be deemed to have accepted the following terms of this statement, and you will be liable for any irregularities due to irregularities. Consequences of use.

1. This product is a driving assistance product. If you rely too much on this system, it may cause a traffic accident.
2. Due to the large viewing angle of the camera, the image display of this product is different from the real environment, please use it with care.
3. Do not operate the system when driving at high speed, so as to avoid traffic accidents caused by distraction.
4. Do not replace product parts without the guidance of professionals, otherwise it will cause damage to the machine.
5. It is forbidden to put this product in wet environment and water to avoid electric shock, unnecessary damage and fire alarm caused by short circuit.
6. The external output voltage of the host of this product is 5V, please do not use an external power supply on this host.
7. Illegal power failure during video recording will cause the last video file to be damaged or lost. The recorded video is damaged or lost due to the destructive collision of the machine during the recording process.

ACCESSORIES

• (Main Device)

• （Rear Camera）

• （ACC Hard wire）

• （Car charging wire）

• （Rear Camera Extension Cable)

Product Introduction

1. Power
2. OK
3. Menu
4. Up
5. Down
6. LED
7. Reset
8. SD Slot
9. USB-C
10. Sticker
11. Speaker
12. Camera Lens
13. Rear Cam Input
14. GPS Receiver

Installation Guide

1. Turn off the car engine.

2. Find an appropriate position on the car, install the recorder, and the installation position should not affect the driving, and then wipe the glass of the installation position clean.

3. Adjust the lens position to ensure that the lens is level with the ground.

4. Car Charger Version: connect the car charger to the cigarette lighter of the dashcam, and connect he other TYPE-C to the dash cam interface.
   

5. The fuse box power version ( 12V to 5V ACC cable) also called Hardware kits is connected to the matching interface B+, ACC. GND, (optional version)
   Another end of TYPE-C is connected to the TYPE-C interface of dashcam.
   Note :

6. B+ yellow wire connects to DC-12V power supply and make it power on always.

7. The ACC red wire connects to the ignition control DC-12V power supply.

8. The GND black wire connects to the metal of car body

9. Install the Rear Camera
   Installation method 1. The position where the rear camera is installed on the rear windshield is only for real-time rear view.
   

Hint:

1. After the installation is completed, please clean the front lens and rear lens, and check that the Sticker is firmly steady.
2. If you choose installation method 1, please clean the rear windshield and the rear camera regularly
3. If you choose installation method 2, please clean the external rear camera and the fixing screw for rear camera regularly
4. After installation, please adjust the camera angle to keep the video in the middle of the road.

About APP

（APP: Viidure)

1. Please scan the above QR code with your mobile phone, follow the hint to download the Viidure APP and install it successfully.
   ( Note : During the installation process, please follow the hint and select all “YES” until the installation is successful)

2. Please connect the to the power supply to turn on the recorder, select the WIFI option in the setting menu and turn it on.

3. Please check that the WIFI name on the phone is exactly the same as the WIFI name on the recorder. SSID: DASAITA****

4. Enter the initial password: 12345678,and the phone will automatically connect.

5. Open Viidure-APP and add the WIFI connected to the recorder.

Warning:

When the car is running, do not try to operate it, please operate the device when the car is stopped.

APP Main Menu

After the recorder is connected to the mobile APP, the current real-time image of the recorder can be displayed in the APP:

1. Find the setting option at the main menu, check out the setting option and the option of formatting TF card.
2. Find the album option at the main menu to check out videos and photo.

1. Enlarge the picture
2. Video Recording Button
3. Video Resolution
4. Photo Album
5. File browse/File download
6. Setting

The Video And Picture Playback of APP Album
The album is where you can find everything your camera has recorded. (including recorded videos, pictures, and locked videos), can be edited and downloaded normally (Note: Only share the content you download.)

1. File list
2. Select
3. Play
4. Video Downloading
5. Video montage
6. Delete
   

Video Recording/playback

Video Recording

When the machine is turned on, it will enter the recording mode, and the upper left corner of the screen will display the recording icon to start recording, and a red dot will flash on the screen in the recording state. At the same time, during the recording, you can’t operate the menu and change working mode. At this time, short press OK to stop recording。

Video Playback

Playback method 1: Press and hold the M key at the photo mode , switch to the playback mode, and the playback icon will be displayed in the upper left corner of the screen ； Short press the up button to select files upwards; Short press the key to select the file down; Short press the OK button to play the selected video file; Short press the menu key to enter the menu settings, where you can delete or unlock files.

Playback method 2: Connect the TF card to the computer through the card reader, select the content in the removable disk, and then play back.

Parking monitoring: instant time-lapse video, ACC cable is required

1. Select “Off” to close the parking monitoring. When the car is turned off, the recorder will automatically shut down.

2. Select “24H”,When the car is turned off, it will enter the parking monitoring and time-lapse recording status. In the case of not starting the car, the recorder will automatically shut down after 24 hours of continuous work.
   (Choose 12H, it will automatically shut down at 12H after turning off the car, and select 48H, it will automatically shut down at 48H after turning off the car)

3. When the car is turned off, it will automatically switch to time-lapse video, which 90 minutes are saved as a 3-minute video (saving video storage memory)
   Powering on the Car automatically switches to normal recording

4. The machine with time-lapse video is equipped with a wire that supports a low-voltage protection box as standard. When the detection of the car battery voltage is lower than 11.6V （which is the low voltage）,
   The protection box automatically cuts off the power supply.

Formatting MICRO-SD Card

1. To ensure the compatibility of the TF card with the recorder, the TF card needs to be formatted on the camera. This driving recorder supports TF card up to 256GB, TF card speed must be level 10 and above.

2. Insert the TF card into the recorder at the non-recording situation, click the M menu button, select the format option,
   Note:

3. After successful formatting, all data will be deleted. Please remember to back up your important data on other devices in advance.

4. Please regular formatting can effectively prevent data loss. Under normal use, it is recommended to format the TF card regularly every month.

5. Every time you insert a TF card, please format it inside your dash camera to ensure that the TF card is compatible with the camera.

Main Functions Introduction

The recorder starts recording when it powers on, click the OK button (to stop recording).

Video Resolution

Recording Time
Current Date and Time
Parking Monitoring On
G-sensor On
Audio Recording on or off
Video Lock
GPS on

Note:

1. Stop recording, the red dot icon flashing on the left disappears;
2. It has been prompted to start recording, but the recording time is displayed: 00:00:00, indicating that the TF card is full
3. If the loop recording is turned on, there is no need to format the TF card, the newly recorded files will automatically overwrite the old files

Setting

When the recorder is at pause , press the M key for a long time to enter the menu “Settings” option.

• Back Return to previous interface
• Resolution Select the video recording resolution: 4K/2K/1080P, different resolutions represent the resolution of the recorded video
• Speaker Volume Select the external sound volume: mute/low/ medium/high, different levels represent different volume output

1. Collision Sensitivity: Select G-SENSOR: Off/High/Medium/Low, different levels represent different G-SENSOR sensitivity.
2. The built-in G sensor will detect the collision and lock the current video file, the locked file will not be overwritten.
3. If the road is bumpy when driving, please adjust to a low position or turn it off directly, in case the memory card is full and the camera can’t work.

• Screen Saver Select off/1 minute/3 minutes/5 minutes, different times represent the time when the screen is automatically closed, select “Off”, the screen will be on for a long time
• Date/Time Select Current Date and Time
• Rear Screen flip: Represents selecting the mirror and original video of the video of rear camera
• Language Multi-language English/Simplified Chinese/Japanese, etc., the selection matches up the current menu language
• Boot Sound Select On/Off to turn on or off the switch sound
• Recording Audio: select On/Off, which means turning on or off the audio recording
• WIFI Select On/Off, which means turning on or off WIFI (pop-up WIFI name and password)
• Plate Number Select Settings Display license plate number
• Parking monitoring: This option needs to support the ACC line connected to the car fuse box (B+, ACC.GND) to realize time-lapse video
• Format: format the current TF card (Note: Formatting will delete all data, please back up data in advance)
• Default Setting: restore factory default settings
• Version: the current software version number of the recorder

Play Videos On Your Computer

Audio Recording can also be viewed on computer. For this you need a separate TF card reader to read the files in the recorder.

VIDEO : Video recorded by the recorder
PHOTO : Photos saved by the recorder
EVENT : Lock file saved by the recorder
( Note : For devices that use dual camera recording, the file name end with “M” is called the front camera, and the file end with “S” is called the rear camera)

Specifications

Hardware Parameters ：

Sensor| High Definition 5M Image Sensor
Screen| 4Inch IPS High Definition Screen
Video format| MOV Format
Speaker| Support
Working Voltage| DC 5V
Storage| TF Card Maximum support 128GB high-speed card
Working Temperature(℃) Features ：| （-10℃-60℃）
Features：
Language| Multi Languages
Loop Recording| Support
Parking Monitoring| Support(Require ACC cable)
G-sensor| Support
Audio| Support
Storage Compression| H.264 Coding

Troubleshooting

Most common Questions:

Q1 : What should I do if I forget the WIFI password of the recorder?
Answer : The initial password of the recorder is: 12345678. If you forget the password after changing it, please contact the manufacturer to reset the software to restore the factory settings.
Q2 : Why format the memory card? How often do you format the TF card?
Answer : Regular formatting can effectively prevent data loss. Under normal use, it is recommended to format the TF card regularly every month. Please back up all data before formatting.
Q3 : How to format the memory card?
Answer : At the main settings menu, format option, click format, confirm the format is completed connect the recorder in the APP, enter the setting option – select the format option, click the format button to confirm that the format is completed.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>