LAIDOUOOU B0B3MMFVYG Wireless HDMI Transmitter and Receiver User Manual
- June 15, 2024
- LAIDOUOOU
Table of Contents
Wireless HD
Transmitter & Receiver
User Manual
Preface
Thank you for purchasing our products, For optimum operation, please read this manual carefully before use.
Features
- Wireless transmit and receive Simply connect the transmitter of this product to a computer, camera or another video output devices equipped with HDMI output port, and connect the receiver to an LCD TV, Projector or other display devices with HDMI input port to realize wireless screen casting The product has been paired out of the factory. It will start working after a simple connection. No need troublesome software setup.
- Allows switching/addition of transmitters Up to eight separate transmitters can be added through simple pairing operations (available through separate purchase), and different transmitters can be switched at the push of a button.
Package Includes
Transmitter(TX) x1
Receiver(RX) 1
USB Charging Cable x2
HDMI Extender Cable x1
User Manual xl
Exquisite Box xl
Name of each part
Receiver- RX
Transmitter – TX
How to connect
STEP 1 Connection of the Receiver(RX)
- Connect the USB Charging cable to the Receiver(RX) and power it with a 5V / 2A AC adapter.
- Connect the HDMI port of the Receiver(RX) to the TV projector, etc.
- Wait a few seconds, and the system screen will appear on the monitor.
※If the system screen s not displayed, please confirm the HDMI signal source of the TV. Example: When the HOMI port is connected to the “HDMI 2″ port of the monitor, please switch the “Signal Source” of the monitor to “HDMI 2°
STEP 2 Connection of the Transmitter(TX)
-
Connect the HDMI port of the Transmitter(TX) to the PC/Laptop, etc.
※ In case the HOMI output port cannot supply sufficient voltage to the transmitter, an external
AC adapter (voltage: 5V 24) is required to power the TX. -
After the indicator light flashes rapidly, wait for about 10 seconds and the projection is completed.
How to re-pair
The product will be paired at factory inspection. If pairing fails or if you need to pair again in other cases, please refer to the following:
- Please connect the receiver to the monitor and the power supply. Connect the transmitter to PC device and power supply.
- Please press and hold the receiver function button for more than 3 seconds, the interface pops up the message: Release the button to pair with EZ Cast TX. At this time the receiver enters the pairing mode and wait for the transmitter to connect.
- Press and hold the transmitter function button for more than 5 seconds, the indicator light appears flashing for pairing, and the transmitter indicator light is always on when the connection is successful.
- Pairing is complete when “Pairing-OK” s displayed on the monitor.
After waiting for a few seconds, the picture from the transmitter will be automatically output to the receiver.
※ Note: One receiver can be paired with up to 8 transmitters.
How to reset
How to reset the receiver;
Press and hold the function button of the receiver for more than 10 seconds to
reset
※ There is no need to re-pair with the transmitter.
How to reset the transmitter:
Press and hold the function button of the transmitter for more than 10 seconds
to reset it
※ Need to re-pair with the receiver.
How to switch transmitters
In the state of multiple transmitter pairing, press the function button of the transmitter to turn off the screen,
- Press the “function button” of the working transmitter, and the screen at the receiving end will return to the system screen.
- Press the *function button” of the transmitter you want to switch to achieve screen switching.
Frequently Asked Questions
1 The wireless HDMI transmitter and receiver can not working properly.
1. Fairing is unpaired. Please try to re-pair. 2. The antenna signal of the receiver is not read properly. Please re-insert the connection order of the receiver in the following order. Connect the USB port of RX and power supply first, then connect HDMI port and monitor. 3. Insufficient power supply. Please use 5V2A adapter to supply power to the transceiver.
2. Unable to pair.
The antenna signal of the receiver is not read properly. Please re-insert the connection of the receiver with following steps. Connect the USB port of RX and power supply first, then connect the HOMI port and monitor.
3. The screen frequently returns to the initial screen.
1. Check and set the device (PC) connected to the. transmitter not to enter the hibernation state. 2. Please reconnect the transmitter with an AC adapter of 5V/2A or more.
4. When communication is interrupted during use due to heat generation of the transmitter, and it takes some time to resume.
1. The power supply to the transmitter is insufficient. Please use 5V/2A adapter to supply power to the transmitter. 2. TX will not work temporarily due to overheating protection fit is used for a long time.
5. Only the image is transmitted, but not the sound.
1. Check whether the stereo sound is turned on, please turn off the stereo sound 2. Please enter the system settings of the transmitter device - Sound -> Switch the speaker.
Customer Support
Support for product issues: info@Aimibo.tv
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference wilt not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Statement To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated at a minimum distance of 20cm from the radiator of your body. This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.
I5ED Statement
This device complies with Industry Canada license-exempt RSS standard(s)
Operation is subject to the following two conditions: (1) This device may not
cause interference, and (2) This device must accept any interference,
including Interference that may cause undesiredoperation of the device.
The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(8)
This device meets the exemption from the routine evaluation limits in Section
2.5 of RSS 102 and compliance with RSS 102 F exposure, users can obtain
Canadian information on F exposure and compliance.
This equipment complies with Canada radiation exposure limits et forth for an
uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
The device for operation in the band 5150-5250 MHZ is only for indoor use to
reduce the potential for harmful interference to co-channel mobile satellite
systems.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>