sunlite 88786-SU LED T-Grid Fixture Instruction Manual
- June 4, 2024
- sunlite
Table of Contents
sunlite 88786-SU LED T-Grid Fixture
Installation
Step 1: Unlock the two nuts at the ends of the fixture (Figure 1).
Step 2: Install the fixture to ceiling grid and tighten the two terminal
nuts (Figure 2 and Figure 3) .
Step 3: Unlock the nuts from both end of Junction box (Figure 4).
Step 4: Secure the junction box to the fixture and tighten the two
terminal nuts ( Figure 5 and Figure 6).
Step 5: Connect the connector (RJ45) from fixture to the output connector
of Function Box (Figure 7).
Please note one driver can only support Max 3 units(Figure 8).
Step 6: Open the Junction box, connect the L (live), N (Neutral), G
(Ground) wires by using the 4-pin connectors and connect the dimming wire with
the orange
connector cap.
Step 7: Cover the plasterboard to finish installation and ensure there is
no opening at ceiling. (Figure 9 and Figure 10)
Wiring Diagram
Please read and understand this entire manual before attempting to assemble,
operate or install the product.
WARNING: Avoid fire or electric shock. Follow installation instructions
carefully. If unsure about electrical installation, consult, a qualified
electrician. Wear rubber-soled shoes and work on a sturdy wooder ladder.
Ground fixture to avoid potential electric shock. Handle metal parts carefully
to prevent cuts. To avoida hazard to children, account for all parts and
destroy all packing material. This product is only suitable for indoor
applications.
CAUTION: Turn off the power at fuse or circuit breaker box before
installation and maintenance.
NOTE: This fixture is suitable for 120-277-Volt fused circuits. Fixture
must be installed according to National Electric Code and local building
codes. If you are unsure about wiring, consult a qualified electrician. THIS
FIXTURE BODY IS ONE PIECE, DO NOT DISASSEMBLE OR MAKE ALTERATIONS.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interence,
and (2) this deivce must accept any interence received, including that may
cause undesired operation.
You can remove the related T-grid from the drop ceiling according to your
shape design. For example, for shape, remove the No.1, No.2. No.3 and No. 4
T-grid;
for shape, remove the No.1, No.2, No.5 and No. 6 T-grid;
Pls note: The adjacent T-grid must be fixed by the pendant. (figure
1)
“L” SHAPE INSTALLTION STEP:
- Step 1. for the No.1 Light fixture, fix the A-end with wire of the No.1 light fixture by pendant and the B-end on the “a” T-Grid.
- Step 2. fix the No. 2 light fixture on the No. 1 light fixture with the A-end with wire, and the B-End on the “b” T-Grid.
SHAPE INSTALLTION STEP: Follow up the “L” shape installation, using the same method as “L” sahpe did, install the No.3 and No.4 light fixture. (Figure, 2, Figure 3, Figure 4, Figure 5)
“T” SHAPE INSTALLTION STEP:
Step 1. Install the No.1 Light fixture, fix the A-End with wire of the
light fixture on the “d” T-Grid and the B-end by pendant.
Step 2. Fix the A-end with wire of the No.2 light fixture on the No.1
light fixture, and the B-end of the fixture on the “e” T-Grid.
Step 3. Using the same method, fix the A-end with wire of the No.5 light
fixture on the “g T-Grid, and the B-end on the “f” T-Grid.
+ SHAPE INSTALLTION STEP:
Follow up the “T” shape installation, and replace the “f” T-Grid with one
light fixture (Figure 7, Figure 8 and Figure 9)
Sunshine Lighting Company
744 Clinton Street Broolklyn, NY 11231, USA
T. 718.768.7000
F. 718.768.0970
www.sunlite.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>