sunlite 88129-SU LED Outdoor Canopy Light Fixture Instruction Manual

: May 15, 2024
: sunlite

Table of Contents

Safety Information
Installation
Customers Support
Read User Manual Online (PDF format)
Download This Manual (PDF format)

sunlite 88129-SU LED Outdoor Canopy Light Fixture

sunlite 88129-SU LED Outdoor Canopy Light Fixture

Safety Information

Please read and understand this entire manual before attempting to assemble, operate or install the product.

WARNING: Risk of fire, Risk of electric shock. Turn power off before inspection, installation, or removal. Before installation, thoroughly review enclosed installation manual. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT A CONDUCTOR. MIN 90’C SUPPLY CONDUCTORS. Operating temperature -40’C to 40’C (-40°F to 103′). Suitable for wet locations.

CAUTION: Turn off the power at fuse or circuit breaker box before installation and maintenance to avoid electric shock. This product should be installed and operated by a qualified electrician or technician in accordance with relevant local codes. This fixture requires a 120-277Volt AC power source. Do not handle energized fixture when hands are wet, when standing on wet or damp surfaces or in water.

Mounting Location: Stem, Junction Box or Surface mounted.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful inference, and (2) this device must accept any inference received, including that may cause undesired operation.

Retain these instructions for future maintenance reference.

Installation

A. JUNCTION BOX MOUNTING

STEP 1. Make sure the power is turned off at the source to the junction box.
STEP 2. According to user’s requirement, loosen the nuts that correspond to CCT and power selectable and tighten with nuts after confirmation. (Fig. 1)
STEP 3. Remove the Mounting Plate and by removing one screw. (Fig. 2)
STEP 4, Fasten the mounting plate to the junction box using the screws supplied with the junction box. (Fig.3)
STEP 5. Complete the wiring to the power source and ground, use the wiring cap make the following electrical connections in the mounting bm< or junction box. Black–Live, White — Neutral, Green — Ground. (Fig 4)
STEP 6. Fasten lighting fixture to the mounting plate using the screw. (Fig. 5)

B. SURFACE MOUNTING

STEP 1. Make sure the power is turned off at the source to the junction box.
STEP 2. According to user’s requirement, loosen the nuts that correspond to CCT and power selectable and tighten with nuts after confirmation. (Fig. 1)
STEP 3. Remove the Mounting Plate and by removing one screw. (Fig. 2)
STEP 4. Secure mounting plate to ceiling with screws. (Fig.3)
STEP 5. Mount fixture onto mounting plate. secure mounting plate with screws. (Fig 4)
STEP 6. Loosen screws in lens and reflector and screw cap in housing. Bring wire through screw hole in housing. branch circuit connect to supply lead of luminaire by wire connector. Install reflector and lens. (Fig. 5)

C. STEM MOUNTING

STEP 1. Make sure the power is turned off at the source to the junction box.
STEP 2. According to user’s requirement, loosen the nuts that correspond to CCT and power selectable and tighten with nuts after confirmation. (Fig. 1)
STEP 3. Remove the Mounting Plate and by removing one screw. (Fig. 2)
STEP 4. Tighten the conduit into lighting fixture. Note: installation conduit shall support four times of weight of luminaire ( Conduit material: steel, thickness 2.5mm, not included) (Fig. 3)
STEP5. Complete the wiring to the power source and ground, use the wiring cap make the following electrical connections in the mounting box or junction box. Black — Live, White — Neutral, Green — Ground.