belkin BOOST CHARGE Magnetic Wireless Charger Stand User Manual

belkin BOOST CHARGE Magnetic Wireless Charger Stand

Test magnet strength before use

Things you need to know before using the product
belkin.com/MagAttachlnfo

Safety information

WARNING: Failure to follow these instructions could result In fire, electric shock, injury, or damage to the user, product, or other property.

1. Connect the wall adapter of the wireless charger into a power outlet that Is close by and is easy to disconnect from the source.
2. Use indoors and in a dry location only; Avoid charging near sources of heat and humidity.
3. Keep the wireless charger and wall adapter away from any liquids or moisture.
4. Unplug the wireless charger when not in use for long periods of time.
5. Do not store your device in very hot or very cold locations. It Is recommended to use your device at room temperature.
6. Do not use if visible defects are observed on the wireless charger or wall adapter.
7. Do not attempt to service. modify. or d is assemble the wireless charger or wall adapter.
8. Use of a wall adapter not recommended or sold by Belkin may result in an increased risk of fire. electric shock, Injury, or damage to the user. product, or other property.
9. Keep t his device out of reach of children to prevent them from playing with it.

CAUTION: If you experience problems with the wireless charger, please discontinue use, unplug t he wall adapter from the AC socket, and contact Belkin for assistance.

The marking information is located at the bottom of apparatus.

WARRANTY AND SUPPORT INFORMATION

IMPORTANT!
PLEASE RETAIN PROOF OF PURCHASE AND PRODUCT WARRANTY INFORMATION BELKIN PRODUCT AND CONNECTED EQUIPMENT LIMITED WARRANTY
(CONNECTED EQUIPMENT WARRANTY NOT AVAILABLE IN LATIN AMERICA)
This warranty Is provided to you by Belkin lntematlonal, Inc, or one of Its subsidiaries or affiliates (“Belkin”)

IMPORTANT NOTICE REGARDING YOUR CONSUMER RIGHTS

The benefits we give in this manufacturer’s warranty are additional to any rights and remedies that you may have under local consumer protection laws. Nothing in this warranty limits or affects your legal rights.

This manufacturer’s warranty is governed by the laws of t he country in which you purchased your Belkin product. In many countries. consumers have rights under local consumer laws. Those consumer rights may differ between countries. states and provinces. and often cannot be excluded. Your local consumer rights organization can advise you on your legal rights.

This manufacturer’s warranty is not intended to:

• change or exclude any rights under consumer law that cannot be lawfully changed or excluded; or
• limit or exclude any right you have against the person who sold the Belkin product to you if that person has breached their sales contract wit h you.

WHAT DOES THIS WARRANTY COVER?

Product Warranty: Belkin warrants that the product hardware and any software media (i.e., media on which the product software is provided) will be free from defects in materials and workmanship under normal use during the Warranty Period described !>@low. This means that the product won’t be defective, and that it will look and work as advertised during the relevant period.

Connected Equipment Warranty: Belkin also covers damage to any equipment which is connected through the Belkin product to a properly wired AC power line with protective ground (Connected Equipment) caused by failure of the Belkin product to operate as described in the product documentation and arising as a result of impulses from lightning, or other power transients, or by momentary (less than 1ms) voltage surges or spikes (an Occurrence) during the Warranty Period (ConMCted Equipment Warranty).

The Connected Equipment Warranty will not apply if damage to the Connected Equipment resulted from:

• telephone-line transients if the Connected Equipment was not properly connected to or was not directly connected to a Belkin product that offers telephone-line transient protection;
• coaxial-line transients If the Connected Equipment was not properly connected to or was not directly connected to a Belkin product that offers coaxial-line transient protection; or
• network-line transients if the Connected Equipment was not properly connected to or was not directly connected to a Belkin product that offers network-line transient protection.

The Connected Equipment Warranty will remain effective for the Warranty Period set out below. The Connected Equipment Warranty automatically ends when the Product Warranty ends.
This warranty does not apply to products purchased from a source other than Belkin or a Belkin Authorized Reseller.

How long Is the product warranted and what Is the maximum value of the Connected Equipment Warranty?
Belkin warrants that the hardware in this Belkin product, and any associated software media, will be free from defects in materials and workmanship under normal use during the Warranty Period. The Warranty Period begins on the date the product was purchased by the original end-user purchaser and lasts for the period set out in the table below. Belkin’s total liability under the Connected Equipment Warranty shall not exceed the maximum aggregate monetary limits set forth in the table below:

Product Type| Warranty Period| Maximum Monetary Limit (US Dollars)
---|---|---
New products| 2 years| S2,500 USD
Replacement products| The longer of the original Warranty Period or 30 days
Software media (if provided with the product)| 90 days| N/A

If the Protected Light indicator on your Belkin product does not come on because your product is dead on arrival, your product will remain covered under this warranty. A product is considered dead on arrival when it does not work when you try to power it on for the first time. Please contact Belkin Technical Support within sixty (60) days from the date of purchase of your product for a replacement (see the section on “Belkin Technical and Warranty Support Information” !>@low). A product given to replace a product that is dead on arrival shall be covered by a fresh warranty having the same duration as the original Warranty Period.

If the Protected Light indicator on the product goes out at any time, this means that the capacity of the product is exceeded, and the product will no longer protect against surges and spikes of energy. Therefore, if the Protected Light indicator on your product goes out, we strongly recommend that you cease using the product immediately. In such an event, If the product Is still within the Warranty Period and if none of the exclusions set out in this warranty apply, please contact Belkin Technical Support for a replacement product.

A claim under this warranty is only eligible if it is made within t he Warrant y Period.

What Isn’t covered by the Product Warranty and Connected Equipment Warranty?
Belkin does not give any warranty:

• in relation to software or services, provided by Belkin or any third party, included in or with the product or Connected Equipment;
• that the product, software or services will always operate uninterrupted or error free;
• that the product, software or services, or any equipment, system or network on which the product, software or services are used are 100″ secure and cannot be hacked; or
• that a third-party service the product or Connected Equipment needs will always be available.
  Note: Although Belkin does not make these promises in this warranty, you may have additional rights under consumer laws.

Will the Product Warranty always apply?
The Product Warranty does not apply If:

• the product has been tampered with or the assembly seal has been removed or damaged:
• the product has been altered or modified by someone other than Belkin;
• the warranty claim was made fraudulently or by misrepresentation;
• the product was not installed, operated, repaired, or maintained in accordance with Bel kin’s Instruct ions (for example, this warranty will not apply if the product has been used outdoors or In a wet area, or if the product has been used together with a generator, heater, sump pump, water-related device, life support device, medical device, car, motorcycle, or golf-cartbanery charger). To be used indoors only and in dry areas. All warranties contained herein are null and void if used in any way with any of the aforementioned devices;
• the product has been subjected to abnormal physical or electrical stress, misuse, negligence, or accident;
• damage to the product Is cosmetic, including scratches and dents. or defects caused by normal wear and tear or normal aging of the product;
• the serial number on the product has been altered, defaced, or removed:
• the product was used in conjunction with other extension cords, power strips, adapters, UPSes, surge protectors, ot her grounding wires or electrical connections; or
• the product was supplied or licensed for beta, evaluation, test ing or demonstration purposes, and you didn’t buy or license the product.

WIii Belkin cover damage to Connected Equipment In 111 situations under the Connected Equipment Warranty?

Belkin does not cover damage to Connected Equipment in the following situations:

• the product was purchased in Latin America, including Mexico, Central America, South America, and the Caribbean (excluding any U.S. or Canadian territories in these regions);
• the Product Warranty has expired or does not apply (please see section above);
• the Connected Equipment was not properly or directly connected to the product;
• not all wires leading into the Connected Equipment, including telephone and coaxial lines, pass through the appropriate product;
• damage to the Connected Equipment was not caused by an Occurrence;
• the power outlet to which the product was connected was not properly grounded or not grounded at all;
• the Connected Equipment has been subjected to abnormal physical or electrical stress, misuse, negligence, or accident;
• damage to the Connected Equipment is cosmetic (including scratches and dents), or damage was caused by normal wear and tear or normal aging of the Connected Equipment;
• damage to the Connected Equipment was caused by an Act of God (other than lightning), Including but not limited to typhoon, hurricane, erosion, earthquake, thunderstorm, inclement weather, flood, tsunami, vandalism, theft, or war;
• damage to t he Connected Equipment was caused by a power outage, a sustained low voltage situation, or a low-volt age disturbance, including but not limited to brownouts or sags;
• repair or replacement of the damaged Connected Equipment is covered by a third party’s manufacturer’s warranty, a seller’s extended warranty, or your Insurance policy;
• Belkin determines that the Connected Equipment was not used under normal operating conditions or in accordance with the manufacturer’s instructions for the Connected Equipment; or you continue to use the product In the knowledge that the Protected Light indicator has gone out.

Note: Although this warranty doesn’t apply in these situations, you may have additional rights under consumer laws.

How will Belkin make things right?

If you make an eligible claim In relation to your defective Belkin product under the Product Warranty, Belkin will, at its election:

• repair the product with new or refurbished parts, or pay the reasonable costs of repairing the product;
• replace the product with a reasonably available equivalent new or refurbished Belkin product; or
• refund you the purchase price of the product, minus any rebates and discounts.

Any repaired or replacement products are warranted for the remainder of the original Warranty Period or 30 days, whichever is longer. All products and parts that are replaced become the property of Belkin.

If you make an eligible claim in relation to your damaged Connected Equipment under the Connected Equipment Warranty. Belkin will, at its option:

1. pay the reasonable costs of repairing the damaged Connected Equipment as assessed by Belkin in Its sole discretion;
2. replace the damaged Connected Equipment with a reasonably available equivalent new or refurbished Connected Equipment (In which case we will engage the repair facility and negotiate and settle t he cost of repair); or
3. refund you the fair market value of the damaged Connected Equipment as reasonably assessed by Belkin in i1s sole discretion.

Belkin makes every reasonable effort to repair or replace your damaged Connected Equipment under this warranty. However, as the repaired or replacement Connected Equipment is manufactured by third parties, Belkin does not make any warranty in relation to such repaired or replacement Connected Equipment, nor is Belkin able to confirm that the manufacturer of the Connected Equipment will offer such a warranty.

All calculations performed by Belkin in evaluating your claim under this warranty are final and binding on you except in the case of errors.

For Belkin to properly and expeditiously validate your claim under this Product Warranty and/ or the Connected Equipment Warranty, you agree that Belkin may examine the damaged product, the damaged Connected Equipment and/or the site where the damage occurred. Belkin reserves its right to do these things until any claim under the Product Warranty and/ or the Connected Equipment Warranty is finalized. The damaged product and damaged Connected Equipment must remain available for inspection during that time.

Do not dispose of the product and Connected Equipment until your claim has been fully resolved. Please review the section titled What do I need to do to make a claim?” under the header “Belkin Technical and Warranty Support Information• below.
Once your claim under this warranty is fully settled, Belkin reserves the right to be subrogated under any existing insurance policies that you may have.
Note: The rights and remedies outlined above are the only rights and remedies available under this warranty. However, you may have additional rights under consumer laws.

GENERAL EXCLUSIONS AND LIMITATIONS OF LIABILITY

IN THOSE JURISDICTIONS WHERE IT CAN LAWFULLY DO SO, AND TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, BELKIN, ITS RESELLERS AND ITS SUPPLIERS HEREBY DISCLAIM AND EXCLUDE ALL OTHER WARRANTIES, EXPRESS, STATUTORY OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, ACCEPTABILITY, SATISFACTORY QUALITY, NON-INFRINGEMENT, TITLE, FITNESS FOR A PARTICULAR PURPOSE, LOSS OF OR DAMAGE TO DATA, LACK OF VIRUSES OR FREE FROM VIRUS OR MALWARE ATTACK, SECURITY, PERFORMANCE, LACK OF NEGLIGENCE, WORKMANLIKE EFFORT, QUIET ENJOYMENT, THAT THE FUNCTIONS CONTAINED IN THE PRODUCT WILL MEET YOUR REQUIREMENTS, OR THAT DEFECTS IN THE PRODUCT WILL BE CORRECTED, OR THAT YOUR USE OF THE PRODUCT WILL GENERATE ACCURATE, RELIABLE, TIMELY RESULTS, INFORMATION, MATERIAL OR DATA. NO ORAL OR WRITTEN INFORMATION OR ADVICE GIVEN BY BELKIN, A DEALER, AGENT OR AFFILIATE SHALL CREATE A WARRANTY. TO THE EXTENT WARRANTIES CANNOT BE DISCLAIMED OR EXCLUDED, THEY ARE LIMITED TO THE DURATION OF THE RELEVANT EXPRESS WARRANTY PERIOD.

EXCEPT AS PROVIDED IN THIS WARRANTY AND TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL BELKIN, ITS AFFILIATES, ASSOCIATES, DEALERS, AGENTS OR SUPPLIERS OR THEIR RESPECTIVE OFFICERS, DIRECTORS, EMPLOYEES. LICENSORS AND ASSIGNS BE LIABLE FOR ANY DIRECT, INDIRECT, EXEMPLARY, PUNITIVE, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO DAMAGES FOR LOSS OF PROFITS OR REVENUE, FOR BUSINESS INTERRUPTION, FOR PERSONAL INJURY, FOR LOSS OF PRIVACY, FOR LOSS OF ABILITY TO USE ANY THIRD PARTY PRODUCTS OR SERVICES, FOR FAILURE TO MEET ANY DUTY INCLUDING OF GOOD FAITH OR OF REASONABLE CARE, FOR NEGLIGENCE, AND FOR ANY OTHER PECUNIARY OR OTHER LOSS WHATSOEVER), REGARDLESS OF THE THEORY OF LIABLITY (CONTRACT, TORT OR OTHERWISE) ARISING OUT OF OR IN ANY WAY RELATED TO THE USE OF OR INABILITY TO USE THE PRODUCT, EVEN IF BELKIN OR SUCH OTHER ENTITIES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL THE TOTAL AGGREGATE LIABILITY OF BELKIN, ITS AFFILIATES, ASSOCIATES, DEALERS, AGENTS OR SUPPLIERS TO YOU FOR ALL DAMAGES EXCEED THE PRICE YOU PAID FOR THE PRODUCT. THIS LIMITATION IS CUMULATIVE AND WILL NOT BE INCREASED BY THE EXISTENCE OF MORE THAN ONE INCIDENT OR CLAIM. THE FOREGOING LIMITATIONS WILL APPLY EVEN IF ANY WARRANTY OR REMEDY PROVIDED FAILS OF ITS ESSENTIAL PURPOSE. NOTHING IN THIS SECTION SHALL LIMIT THE LIABILITY OF BELKIN IN RELATION TO DEATH OR BODILY INJURIES.

THE WARRANTIES AND REMEDIES SET OUT IN THIS AGREEMENT ARE EXCLUSIVE, AND, TO THE EXTENT PERMITTED BY LAW, IN LIEU OF ALL OTHERS ORAL OR WRITTEN, EXPRESS OR IMPLIED. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IMPLIED WARRANTIES OR OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE FOREGOING LIMITATIONS MAY NOT APPLY TO YOU.

If any term Is held to be Illegal or unenforceable, the legality or enforceability of the remaining terms shall not be affected or Impaired.

BELKIN TECHNICAL AND WARRANTY SUPPORT INFORMATION HOW DO I GET HELP?

If you have a question about your product or experience a problem with it, please go to http://www.belkin.com/support. You will find lots of on line support tools and information to help you with your product.

What should I do If my product 11 defective?

You always have the option to return the product to the original seller if you have a problem. You can make a claim based on this warranty or any consumer laws that apply to you.

You can also make a claim under this warranty or local consumer laws by contacting Belkin Technical Support.

To find out how to contact us. click the ·contact Us” link on the home page of
http://www.belkin.com. If you are located outside the United States, you will need to choose your region/location first:
For Belkin.com:
http://www.belkin.com/us/ – CIick the “Change Region” link at the bottom of the website and select your location.

If I believe my product Is defective and covered by the Product Warranty or the Connected Equipment Warranty, what do l need to do?

You will need to contact Technical Support for your region at the links above. So that we can help you, you will need to give us some information when you contact us:

• your product model, hardware revision and serial number;
• the name of your Internet Service Provider (ISP); and
• proof that you purchased the product, with the date of the purchase shown and place where it was purchased. WE WILL ALWAYS NEED A DATED PROOF OF ORIGINAL PURCHASE TO PROCESS WARRANTY CLAIMS.

Sometimes we will need you to send the product or Connected Equipment back to us so that we can fix or replace it. If we ask you to return your product to us by post, you will be given a Return Materials Authorization (RMA) number and we’ll tell you where to send the product and/or Connected Equipment. You will need to make sure the product and/or Connected Equipment Is properly packaged and shipped, and you will be responsible for the costs of returning your product and/or Connected Equipment to us. We need to identify your product and/or Connected Equipment when It reaches us, so you’ll need to Include the RMA number AND a copy of your dated proof of original purchase (please keep the original) with the returned product and/or Connected Equipment. We also recommend that you send the package by registered and insured mail or by overnight courier to protect the package while it Is in transit. If Belkin determines, In its sole discretion, that It Is impractical to ship the damaged Connected Equipment to Belkin, Belkin may designate, In its sole discretion, an equipment repair facility to inspect and estimate the cost to repair such Connected Equipment. In that case, Belkin reserves the right to negotiate the cost of repairs. The cost, If any, of shipping the Connected Equipment to such repair facility and of such estimate shall be borne solely by the original end-user purchaser.

If you are making a claim in respect of your damaged Connected Equipment, you must do so within fifteen (15) days from the date of the Occurrence. So that we can process your claim expeditiously, we will need the following information in addition to the information described above when you contact us: description of all the equipment that was connected to the product at the time of the Occurrence, Including name and model number; purchase of the damaged Connected Equipment; description of the damaged Connected Equipment and the extent of damage (we may request that you send us photographs of the damaged Connected Equipment and the site where the damage occurred, or we may ask to examine the site where the damage occurred, to help us validate your claim); and the date of the Occurrence.

What happens when I retvm my product or Connected Equipment?

Defective products covered by the Product Warranty will be replaced without charge with the same product or an equivalent product of equal or greater value, or Belkin will provide you with a refund of the purchase price of the product, minus any rebates and discounts. The remedy offered will be determined by Belkin in its sole discretion.

In relation to damaged Connected Equipment covered by the Connected Equipment Warranty, Belkin will pay the reasonable costs of repair as assessed by Belkin at it discretion, replace the Connected Equipment with a reasonably available equivalent new or refurbished Connected Equipment (engaging the repair facility and negotiating and settling the cost of repair), or refund the fair market value as reasonably assessed by Belkin at its sole discretion.

We can only ship replacement or repaired products to locations in the country where the original product was purchased.

Belkin may need to delete all or part of your data to repair or replace your product. Belkin may also install software updates as part of warranty service. PLEASE MAKE SURE THAT YOU BACK UP ALL OF YOUR DATA ON THE PRODUCT BEFORE SENDING IT IN FOR REPAIR OR REPLACEMENT. BELKIN IS NOT RESPONSIBLE FOR ANY LOSS OF DATA OR SOFTWARE DURING WARRANTY SERVICE.

Replacements not covered under warranty or your rights under consumer law may be refused by place of purchase, or may be subject to charge.

FCC Statement

DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY

We, Belkin International, Inc., of 12045 E. Waterfront Drive, Playa Vist a, CA 90094, Tel: +1 (310) 751 5100, declare under our sole responsibility that the product WIB003, to which this declaration relates, complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference. and (2) this device must accept any Interference received, including interference that may cause undesired operation.

Federal Communications Commission Interference Statement

This equipment has been tested and found to comply with t he limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses. and can radiate radio frequency energy, and if not installed and used in accordance with t he instructions, may cause harmful Interference to radio communications. However, there Is no guarantee t hat interference will not occur in a particular Installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase t he distance between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by t he party responsible for compliance could void the user’s authority to operate this equipment.

Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance wit h FCC RF exposure compliance requirements. please follow operation Instructions as documented In this manual. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

Innovation, Science, and Economic Development Canada Statement (ISED):

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Radiation Exposure Statement:
This equipment compiles with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be Installed and operated with a minimum distance of 20 cm between the radiator and your body.

Innovation, Science and Economic Development Canada Statement:
This digital apparatus complies wit h CAN ICES-3(8)/NMB-3 (B).

Belkin International, Inc. Los Angeles, CA 90094, USA
Belkin Asia Pacific Ltd. Hong Kong
Belkin Tech Support: www.belkln.com/support
Made in Vietnam.
belkln.com

References

• Mobile & Computer Accessory Products | Belkin US
• Be Ready For Today | Belkin US
• Mobile & Computer Accessory Products | Belkin US
• Mobile & Computer Accessory Products | Belkin US

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>